/*
* Function ircomm_tty_set_termios (tty, old_termios)
*
* This routine allows the tty driver to be notified when device's
* termios settings have changed. Note that a well-designed tty driver
* should be prepared to accept the case where old == NULL, and try to
* do something rational.
*/
void ircomm_tty_set_termios(struct tty_struct *tty,
struct ktermios *old_termios)
{
struct ircomm_tty_cb *self = (struct ircomm_tty_cb *) tty->driver_data;
unsigned int cflag = tty->termios->c_cflag;
IRDA_DEBUG(2, "%s()\n", __func__ );
if ((cflag == old_termios->c_cflag) &&
(RELEVANT_IFLAG(tty->termios->c_iflag) ==
RELEVANT_IFLAG(old_termios->c_iflag)))
{
return;
}
ircomm_tty_change_speed(self);
/* Handle transition to B0 status */
if ((old_termios->c_cflag & CBAUD) &&
!(cflag & CBAUD)) {
self->settings.dte &= ~(IRCOMM_DTR|IRCOMM_RTS);
ircomm_param_request(self, IRCOMM_DTE, TRUE);
}
/* Handle transition away from B0 status */
if (!(old_termios->c_cflag & CBAUD) &&
(cflag & CBAUD)) {
self->settings.dte |= IRCOMM_DTR;
if (!(tty->termios->c_cflag & CRTSCTS) ||
!test_bit(TTY_THROTTLED, &tty->flags)) {
self->settings.dte |= IRCOMM_RTS;
}
ircomm_param_request(self, IRCOMM_DTE, TRUE);
}
/* Handle turning off CRTSCTS */
if ((old_termios->c_cflag & CRTSCTS) &&
!(tty->termios->c_cflag & CRTSCTS))
{
tty->hw_stopped = 0;
ircomm_tty_start(tty);
}
}
static void ircomm_port_raise_dtr_rts(struct tty_port *port, int raise)
{
struct ircomm_tty_cb *self = container_of(port, struct ircomm_tty_cb,
port);
/*
* Here, we use to lock those two guys, but as ircomm_param_request()
* does it itself, I don't see the point (and I see the deadlock).
* Jean II
*/
if (raise)
self->settings.dte |= IRCOMM_RTS | IRCOMM_DTR;
else
self->settings.dte &= ~(IRCOMM_RTS | IRCOMM_DTR);
ircomm_param_request(self, IRCOMM_DTE, TRUE);
}
/*
* Function ircomm_tty_change_speed (driver)
*
* Change speed of the driver. If the remote device is a DCE, then this
* should make it change the speed of its serial port
*/
static void ircomm_tty_change_speed(struct ircomm_tty_cb *self)
{
unsigned cflag, cval;
int baud;
IRDA_DEBUG(2, "%s()\n", __func__ );
if (!self->tty || !self->tty->termios || !self->ircomm)
return;
cflag = self->tty->termios->c_cflag;
/* byte size and parity */
switch (cflag & CSIZE) {
case CS5: cval = IRCOMM_WSIZE_5; break;
case CS6: cval = IRCOMM_WSIZE_6; break;
case CS7: cval = IRCOMM_WSIZE_7; break;
case CS8: cval = IRCOMM_WSIZE_8; break;
default: cval = IRCOMM_WSIZE_5; break;
}
if (cflag & CSTOPB)
cval |= IRCOMM_2_STOP_BIT;
if (cflag & PARENB)
cval |= IRCOMM_PARITY_ENABLE;
if (!(cflag & PARODD))
cval |= IRCOMM_PARITY_EVEN;
/* Determine divisor based on baud rate */
baud = tty_get_baud_rate(self->tty);
if (!baud)
baud = 9600; /* B0 transition handled in rs_set_termios */
self->settings.data_rate = baud;
ircomm_param_request(self, IRCOMM_DATA_RATE, FALSE);
/* CTS flow control flag and modem status interrupts */
if (cflag & CRTSCTS) {
self->flags |= ASYNC_CTS_FLOW;
self->settings.flow_control |= IRCOMM_RTS_CTS_IN;
/* This got me. Bummer. Jean II */
if (self->service_type == IRCOMM_3_WIRE_RAW)
IRDA_WARNING("%s(), enabling RTS/CTS on link that doesn't support it (3-wire-raw)\n", __func__);
} else {
self->flags &= ~ASYNC_CTS_FLOW;
self->settings.flow_control &= ~IRCOMM_RTS_CTS_IN;
}
if (cflag & CLOCAL)
self->flags &= ~ASYNC_CHECK_CD;
else
self->flags |= ASYNC_CHECK_CD;
#if 0
/*
* Set up parity check flag
*/
if (I_INPCK(self->tty))
driver->read_status_mask |= LSR_FE | LSR_PE;
if (I_BRKINT(driver->tty) || I_PARMRK(driver->tty))
driver->read_status_mask |= LSR_BI;
/*
* Characters to ignore
*/
driver->ignore_status_mask = 0;
if (I_IGNPAR(driver->tty))
driver->ignore_status_mask |= LSR_PE | LSR_FE;
if (I_IGNBRK(self->tty)) {
self->ignore_status_mask |= LSR_BI;
/*
* If we're ignore parity and break indicators, ignore
* overruns too. (For real raw support).
*/
if (I_IGNPAR(self->tty))
self->ignore_status_mask |= LSR_OE;
}
#endif
self->settings.data_format = cval;
ircomm_param_request(self, IRCOMM_DATA_FORMAT, FALSE);
ircomm_param_request(self, IRCOMM_FLOW_CONTROL, TRUE);
}
