/*
* Application entry point.
*/
int main(void) {
/*
* System initializations.
* - HAL initialization, this also initializes the configured device drivers
* and performs the board-specific initializations.
* - Kernel initialization, the main() function becomes a thread and the
* RTOS is active.
*/
halInit();
chSysInit();
/* Initializes a serial-over-USB CDC driver.*/
sduObjectInit(&SDU1);
sduStart(&SDU1, &serusbcfg);
/*
* Activates the USB driver and then the USB bus pull-up on D+.
* Note, a delay is inserted in order to not have to disconnect the cable
* after a reset.
*/
usbDisconnectBus(serusbcfg.usbp);
chThdSleepMilliseconds(1500);
usbStart(serusbcfg.usbp, &usbcfg);
usbConnectBus(serusbcfg.usbp);
/* Creates the blinker thread.*/
chThdCreateStatic(waThread1, sizeof(waThread1), NORMALPRIO + 1, Thread1, NULL);
/* L3GD20 Object Initialization.*/
l3gd20ObjectInit(&L3GD20D1);
/* Activates the L3GD20 driver.*/
l3gd20Start(&L3GD20D1, &l3gd20cfg);
/* Shell manager initialization.*/
shellInit();
while(TRUE) {
if (SDU1.config->usbp->state == USB_ACTIVE) {
thread_t *shelltp = chThdCreateFromHeap(NULL, SHELL_WA_SIZE,
"shell", NORMALPRIO + 1,
shellThread, (void *)&shell_cfg1);
chThdWait(shelltp); /* Waiting termination. */
}
chThdSleepMilliseconds(1000);
}
l3gd20Stop(&L3GD20D1);
return 0;
}
/*
* Application entry point.
*/
int main(void) {
/*
* System initializations.
* - HAL initialization, this also initializes the configured device drivers
* and performs the board-specific initializations.
* - Kernel initialization, the main() function becomes a thread and the
* RTOS is active.
*/
halInit();
chSysInit();
/*
* Initializes a serial-over-USB CDC driver.
*/
sduObjectInit(&SDU1);
sduStart(&SDU1, &serusbcfg);
/*
* Activates the USB driver and then the USB bus pull-up on D+.
* Note, a delay is inserted in order to not have to disconnect the cable
* after a reset.
*/
usbDisconnectBus(serusbcfg.usbp);
chThdSleepMilliseconds(1500);
usbStart(serusbcfg.usbp, &usbcfg);
usbConnectBus(serusbcfg.usbp);
/*
* Creates the blinker thread.
*/
chThdCreateStatic(waThread1, sizeof(waThread1), NORMALPRIO + 1, Thread1, NULL);
/*
* L3GD20 Object Initialization
*/
l3gd20ObjectInit(&L3GD20D1);
/*
* Activates the L3GD20 driver.
*/
l3gd20Start(&L3GD20D1, &l3gd20cfg);
while(!palReadLine(LINE_BUTTON)){
chprintf(chp, "Press BTN to calibrate gyroscope...\r\n");
chThdSleepMilliseconds(150);
#if CHPRINTF_USE_ANSI_CODE
chprintf(chp, "\033[2J\033[1;1H");
#endif
}
chprintf(chp, "Calibrating Gyroscope sampling bias...\r\n");
chprintf(chp, "Keep it in the rest position while red LED is on\r\n");
chThdSleepMilliseconds(3000);
palSetLine(LINE_LED10_RED);
chThdSleepMilliseconds(1000);
gyroscopeSampleBias(&L3GD20D1);
palClearLine(LINE_LED10_RED);
#if CHPRINTF_USE_ANSI_CODE
chprintf(chp, "\033[2J\033[1;1H");
#endif
while (TRUE) {
palToggleLine(LINE_LED10_RED);
gyroscopeReadRaw(&L3GD20D1, rawdata);
for(i = 0; i < L3GD20_NUMBER_OF_AXES; i++)
chprintf(chp, "RAW-%c:%d\r\n", axesID[i], rawdata[i]);
gyroscopeReadCooked(&L3GD20D1, cookeddata);
for(i = 0; i < L3GD20_NUMBER_OF_AXES; i++)
chprintf(chp, "COOKED-%c:%.3f\r\n", axesID[i], cookeddata[i]);
gyroscopeGetTemp(&L3GD20D1, &temperature);
chprintf(chp, "TEMP:%.1f C°\r\n", temperature);
chThdSleepMilliseconds(150);
#if CHPRINTF_USE_ANSI_CODE
chprintf(chp, "\033[2J\033[1;1H");
#endif
}
l3gd20Stop(&L3GD20D1);
}
