/**
* omap36xx_pwrdn_clk_enable_with_hsdiv_restore - enable clocks suffering
* from HSDivider PWRDN problem Implements Errata ID: i556.
* @clk: DPLL output struct clk
*
* 3630 only: dpll3_m3_ck, dpll4_m2_ck, dpll4_m3_ck, dpll4_m4_ck,
* dpll4_m5_ck & dpll4_m6_ck dividers gets loaded with reset
* valueafter their respective PWRDN bits are set. Any dummy write
* (Any other value different from the Read value) to the
* corresponding CM_CLKSEL register will refresh the dividers.
*/
int omap36xx_pwrdn_clk_enable_with_hsdiv_restore(struct clk_hw *clk)
{
struct clk_divider *parent;
struct clk_hw *parent_hw;
u32 dummy_v, orig_v;
struct clk_hw_omap *omap_clk = to_clk_hw_omap(clk);
int ret;
/* Clear PWRDN bit of HSDIVIDER */
ret = omap2_dflt_clk_enable(clk);
parent_hw = __clk_get_hw(__clk_get_parent(clk->clk));
parent = to_clk_divider(parent_hw);
/* Restore the dividers */
if (!ret) {
orig_v = omap2_clk_readl(omap_clk, parent->reg);
dummy_v = orig_v;
/* Write any other value different from the Read value */
dummy_v ^= (1 << parent->shift);
omap2_clk_writel(dummy_v, omap_clk, parent->reg);
/* Write the original divider */
omap2_clk_writel(orig_v, omap_clk, parent->reg);
}
return ret;
}
/**
* omap2_dflt_clk_disable - disable a clock in the hardware
* @hw: struct clk_hw * of the clock to disable
*
* Disable the clock @hw in the hardware, and call into the OMAP
* clockdomain code to "disable" the corresponding clockdomain if all
* clocks/hwmods in that clockdomain are now disabled. No return
* value.
*/
void omap2_dflt_clk_disable(struct clk_hw *hw)
{
struct clk_hw_omap *clk;
u32 v;
clk = to_clk_hw_omap(hw);
if (!clk->enable_reg) {
/*
* 'independent' here refers to a clock which is not
* controlled by its parent.
*/
pr_err("%s: independent clock %s has no enable_reg\n",
__func__, __clk_get_name(hw->clk));
return;
}
v = omap2_clk_readl(clk, clk->enable_reg);
if (clk->flags & INVERT_ENABLE)
v |= (1 << clk->enable_bit);
else
v &= ~(1 << clk->enable_bit);
omap2_clk_writel(v, clk, clk->enable_reg);
/* No OCP barrier needed here since it is a disable operation */
if (clkdm_control && clk->clkdm)
clkdm_clk_disable(clk->clkdm, hw->clk);
}
/* _omap3_dpll_write_clken - write clken_bits arg to a DPLL's enable bits */
static void _omap3_dpll_write_clken(struct clk_hw_omap *clk, u8 clken_bits)
{
const struct dpll_data *dd;
u32 v;
dd = clk->dpll_data;
v = omap2_clk_readl(clk, dd->control_reg);
v &= ~dd->enable_mask;
v |= clken_bits << __ffs(dd->enable_mask);
omap2_clk_writel(v, clk, dd->control_reg);
}
void omap4_dpllmx_deny_gatectrl(struct clk_hw_omap *clk)
{
u32 v;
u32 mask;
if (!clk || !clk->clksel_reg)
return;
mask = clk->flags & CLOCK_CLKOUTX2 ?
OMAP4430_DPLL_CLKOUTX2_GATE_CTRL_MASK :
OMAP4430_DPLL_CLKOUT_GATE_CTRL_MASK;
v = omap2_clk_readl(clk, clk->clksel_reg);
/* Set the bit to deny gatectrl */
v |= mask;
omap2_clk_writel(v, clk, clk->clksel_reg);
}
void omap4_dpllmx_allow_gatectrl(struct clk_hw_omap *clk)
{
u32 v;
u32 mask;
if (!clk || !clk->clksel_reg || !cpu_is_omap44xx())
return;
mask = clk->flags & CLOCK_CLKOUTX2 ?
OMAP4430_DPLL_CLKOUTX2_GATE_CTRL_MASK :
OMAP4430_DPLL_CLKOUT_GATE_CTRL_MASK;
v = omap2_clk_readl(clk, clk->clksel_reg);
/* Clear the bit to allow gatectrl */
v &= ~mask;
omap2_clk_writel(v, clk, clk->clksel_reg);
}
/**
* omap2_dflt_clk_enable - enable a clock in the hardware
* @hw: struct clk_hw * of the clock to enable
*
* Enable the clock @hw in the hardware. We first call into the OMAP
* clockdomain code to "enable" the corresponding clockdomain if this
* is the first enabled user of the clockdomain. Then program the
* hardware to enable the clock. Then wait for the IP block that uses
* this clock to leave idle (if applicable). Returns the error value
* from clkdm_clk_enable() if it terminated with an error, or -EINVAL
* if @hw has a null clock enable_reg, or zero upon success.
*/
int omap2_dflt_clk_enable(struct clk_hw *hw)
{
struct clk_hw_omap *clk;
u32 v;
int ret = 0;
clk = to_clk_hw_omap(hw);
if (clkdm_control && clk->clkdm) {
ret = clkdm_clk_enable(clk->clkdm, hw->clk);
if (ret) {
WARN(1, "%s: could not enable %s's clockdomain %s: %d\n",
__func__, __clk_get_name(hw->clk),
clk->clkdm->name, ret);
return ret;
}
}
if (unlikely(clk->enable_reg == NULL)) {
pr_err("%s: %s missing enable_reg\n", __func__,
__clk_get_name(hw->clk));
ret = -EINVAL;
goto err;
}
/* FIXME should not have INVERT_ENABLE bit here */
v = omap2_clk_readl(clk, clk->enable_reg);
if (clk->flags & INVERT_ENABLE)
v &= ~(1 << clk->enable_bit);
else
v |= (1 << clk->enable_bit);
omap2_clk_writel(v, clk, clk->enable_reg);
v = omap2_clk_readl(clk, clk->enable_reg); /* OCP barrier */
if (clk->ops && clk->ops->find_idlest)
_omap2_module_wait_ready(clk);
return 0;
err:
if (clkdm_control && clk->clkdm)
clkdm_clk_disable(clk->clkdm, hw->clk);
return ret;
}
/**
* omap3_dpll_deny_idle - prevent DPLL from automatically idling
* @clk: struct clk * of the DPLL to operate on
*
* Disable DPLL automatic idle control. No return value.
*/
void omap3_dpll_deny_idle(struct clk_hw_omap *clk)
{
const struct dpll_data *dd;
u32 v;
if (!clk || !clk->dpll_data)
return;
dd = clk->dpll_data;
if (!dd->autoidle_reg)
return;
v = omap2_clk_readl(clk, dd->autoidle_reg);
v &= ~dd->autoidle_mask;
v |= DPLL_AUTOIDLE_DISABLE << __ffs(dd->autoidle_mask);
omap2_clk_writel(v, clk, dd->autoidle_reg);
}
/**
* omap3_dpll_allow_idle - enable DPLL autoidle bits
* @clk: struct clk * of the DPLL to operate on
*
* Enable DPLL automatic idle control. This automatic idle mode
* switching takes effect only when the DPLL is locked, at least on
* OMAP3430. The DPLL will enter low-power stop when its downstream
* clocks are gated. No return value.
*/
void omap3_dpll_allow_idle(struct clk_hw_omap *clk)
{
const struct dpll_data *dd;
u32 v;
if (!clk || !clk->dpll_data)
return;
dd = clk->dpll_data;
if (!dd->autoidle_reg)
return;
/*
* REVISIT: CORE DPLL can optionally enter low-power bypass
* by writing 0x5 instead of 0x1. Add some mechanism to
* optionally enter this mode.
*/
v = omap2_clk_readl(clk, dd->autoidle_reg);
v &= ~dd->autoidle_mask;
v |= DPLL_AUTOIDLE_LOW_POWER_STOP << __ffs(dd->autoidle_mask);
omap2_clk_writel(v, clk, dd->autoidle_reg);
}
/*
* _omap3_noncore_dpll_program - set non-core DPLL M,N values directly
* @clk: struct clk * of DPLL to set
* @freqsel: FREQSEL value to set
*
* Program the DPLL with the last M, N values calculated, and wait for
* the DPLL to lock. Returns -EINVAL upon error, or 0 upon success.
*/
static int omap3_noncore_dpll_program(struct clk_hw_omap *clk, u16 freqsel)
{
struct dpll_data *dd = clk->dpll_data;
u8 dco, sd_div;
u32 v;
/* 3430 ES2 TRM: 4.7.6.9 DPLL Programming Sequence */
_omap3_noncore_dpll_bypass(clk);
if (dd->sink_clkdm)
clkdm_clk_enable(dd->sink_clkdm, clk->hw.clk);
/*
* Set jitter correction. Jitter correction applicable for OMAP343X
* only since freqsel field is no longer present on other devices.
*/
if (cpu_is_omap343x()) {
v = omap2_clk_readl(clk, dd->control_reg);
v &= ~dd->freqsel_mask;
v |= freqsel << __ffs(dd->freqsel_mask);
omap2_clk_writel(v, clk, dd->control_reg);
}
/* Set DPLL multiplier, divider */
v = omap2_clk_readl(clk, dd->mult_div1_reg);
/* Handle Duty Cycle Correction */
if (dd->dcc_mask) {
if (dd->last_rounded_rate >= dd->dcc_rate)
v |= dd->dcc_mask; /* Enable DCC */
else
v &= ~dd->dcc_mask; /* Disable DCC */
}
v &= ~(dd->mult_mask | dd->div1_mask);
v |= dd->last_rounded_m << __ffs(dd->mult_mask);
v |= (dd->last_rounded_n - 1) << __ffs(dd->div1_mask);
/* Configure dco and sd_div for dplls that have these fields */
if (dd->dco_mask) {
_lookup_dco(clk, &dco, dd->last_rounded_m, dd->last_rounded_n);
v &= ~(dd->dco_mask);
v |= dco << __ffs(dd->dco_mask);
}
if (dd->sddiv_mask) {
_lookup_sddiv(clk, &sd_div, dd->last_rounded_m,
dd->last_rounded_n);
v &= ~(dd->sddiv_mask);
v |= sd_div << __ffs(dd->sddiv_mask);
}
omap2_clk_writel(v, clk, dd->mult_div1_reg);
/* Set 4X multiplier and low-power mode */
if (dd->m4xen_mask || dd->lpmode_mask) {
v = omap2_clk_readl(clk, dd->control_reg);
if (dd->m4xen_mask) {
if (dd->last_rounded_m4xen)
v |= dd->m4xen_mask;
else
v &= ~dd->m4xen_mask;
}
if (dd->lpmode_mask) {
if (dd->last_rounded_lpmode)
v |= dd->lpmode_mask;
else
v &= ~dd->lpmode_mask;
}
omap2_clk_writel(v, clk, dd->control_reg);
}
/* We let the clock framework set the other output dividers later */
/* REVISIT: Set ramp-up delay? */
_omap3_noncore_dpll_lock(clk);
if (dd->sink_clkdm)
clkdm_clk_disable(dd->sink_clkdm, clk->hw.clk);
return 0;
}
