static void omap2_enter_mpu_retention(void)
{
int only_idle = 0;
if (omap2_i2c_active())
return;
if (omap2_allow_mpu_retention()) {
omap2_prm_write_mod_reg(0xffffffff, CORE_MOD, PM_WKST1);
omap2_prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP24XX_PM_WKST2);
omap2_prm_write_mod_reg(0xffffffff, WKUP_MOD, PM_WKST);
omap2_prm_write_mod_reg((0x01 << OMAP_POWERSTATE_SHIFT) |
OMAP_LOGICRETSTATE_MASK,
MPU_MOD, OMAP2_PM_PWSTCTRL);
} else {
omap2_prm_write_mod_reg(OMAP_LOGICRETSTATE_MASK, MPU_MOD,
OMAP2_PM_PWSTCTRL);
only_idle = 1;
}
omap2_sram_idle();
}
static void omap2_enter_mpu_retention(void)
{
int only_idle = 0;
/* Putting MPU into the WFI state while a transfer is active
* seems to cause the I2C block to timeout. Why? Good question. */
if (omap2_i2c_active())
return;
/* The peripherals seem not to be able to wake up the MPU when
* it is in retention mode. */
if (omap2_allow_mpu_retention()) {
/* REVISIT: These write to reserved bits? */
omap2_prm_write_mod_reg(0xffffffff, CORE_MOD, PM_WKST1);
omap2_prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP24XX_PM_WKST2);
omap2_prm_write_mod_reg(0xffffffff, WKUP_MOD, PM_WKST);
/* Try to enter MPU retention */
omap2_prm_write_mod_reg((0x01 << OMAP_POWERSTATE_SHIFT) |
OMAP_LOGICRETSTATE_MASK,
MPU_MOD, OMAP2_PM_PWSTCTRL);
} else {
/* Block MPU retention */
omap2_prm_write_mod_reg(OMAP_LOGICRETSTATE_MASK, MPU_MOD,
OMAP2_PM_PWSTCTRL);
only_idle = 1;
}
omap2_sram_idle();
}
static void __init prcm_setup_regs(void)
{
int i, num_mem_banks;
struct powerdomain *pwrdm;
omap2_prm_write_mod_reg(OMAP24XX_AUTOIDLE_MASK, OCP_MOD,
OMAP2_PRCM_SYSCONFIG_OFFSET);
num_mem_banks = pwrdm_get_mem_bank_count(core_pwrdm);
for (i = 0; i < num_mem_banks; i++)
pwrdm_set_mem_retst(core_pwrdm, i, PWRDM_POWER_RET);
pwrdm_set_next_pwrst(core_pwrdm, PWRDM_POWER_RET);
pwrdm_set_logic_retst(mpu_pwrdm, PWRDM_POWER_RET);
pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_RET);
pwrdm = clkdm_get_pwrdm(dsp_clkdm);
pwrdm_set_next_pwrst(pwrdm, PWRDM_POWER_OFF);
clkdm_sleep(dsp_clkdm);
pwrdm = clkdm_get_pwrdm(gfx_clkdm);
pwrdm_set_next_pwrst(pwrdm, PWRDM_POWER_OFF);
clkdm_sleep(gfx_clkdm);
clkdm_for_each(omap_pm_clkdms_setup, NULL);
clkdm_add_wkdep(mpu_clkdm, wkup_clkdm);
#ifdef CONFIG_SUSPEND
omap_pm_suspend = omap2_enter_full_retention;
#endif
omap2_prm_write_mod_reg(15 << OMAP_SETUP_TIME_SHIFT, OMAP24XX_GR_MOD,
OMAP2_PRCM_CLKSSETUP_OFFSET);
omap2_prm_write_mod_reg(2 << OMAP_SETUP_TIME_SHIFT, OMAP24XX_GR_MOD,
OMAP2_PRCM_VOLTSETUP_OFFSET);
omap2_prm_write_mod_reg(OMAP24XX_AUTO_EXTVOLT_MASK |
(0x1 << OMAP24XX_SETOFF_LEVEL_SHIFT) |
OMAP24XX_MEMRETCTRL_MASK |
(0x1 << OMAP24XX_SETRET_LEVEL_SHIFT) |
(0x0 << OMAP24XX_VOLT_LEVEL_SHIFT),
OMAP24XX_GR_MOD, OMAP2_PRCM_VOLTCTRL_OFFSET);
omap2_prm_write_mod_reg(OMAP24XX_EN_GPIOS_MASK | OMAP24XX_EN_GPT1_MASK,
WKUP_MOD, PM_WKEN);
}
static int __init omap_prcm_store_and_clear_reset_sources(void)
{
/* XXX This presumably needs modification for 34XX */
if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
reset_reason =
omap2_prm_read_mod_reg(WKUP_MOD, OMAP2_RM_RSTST) & 0x7f;
/* clear reset reason register */
omap2_prm_write_mod_reg(reset_reason, WKUP_MOD, OMAP2_RM_RSTST);
} else if (cpu_is_omap44xx()) {
reset_reason =
omap4_prm_read_inst_reg(OMAP4430_PRM_DEVICE_INST,
OMAP4_PRM_RSTST_OFFSET) & 0x7ff;
/* clear reset reason register */
omap4_prm_write_inst_reg(reset_reason,
OMAP4430_PRM_DEVICE_INST,
OMAP4_PRM_RSTST_OFFSET);
} else if (cpu_is_omap543x()) {
reset_reason =
omap4_prm_read_inst_reg(OMAP54XX_PRM_DEVICE_INST,
OMAP54XX_PRM_RSTST_OFFSET)
& 0x7fff;
/* clear reset reason register */
omap4_prm_write_inst_reg(reset_reason, OMAP54XX_PRM_DEVICE_INST,
OMAP54XX_PRM_RSTST_OFFSET);
}
return 0;
}
/*
* PRCM Interrupt Handler Helper Function
*
* The purpose of this function is to clear any wake-up events latched
* in the PRCM PM_WKST_x registers. It is possible that a wake-up event
* may occur whilst attempting to clear a PM_WKST_x register and thus
* set another bit in this register. A while loop is used to ensure
* that any peripheral wake-up events occurring while attempting to
* clear the PM_WKST_x are detected and cleared.
*/
static int prcm_clear_mod_irqs(s16 module, u8 regs)
{
u32 wkst, fclk, iclk, clken;
u16 wkst_off = (regs == 3) ? OMAP3430ES2_PM_WKST3 : PM_WKST1;
u16 fclk_off = (regs == 3) ? OMAP3430ES2_CM_FCLKEN3 : CM_FCLKEN1;
u16 iclk_off = (regs == 3) ? CM_ICLKEN3 : CM_ICLKEN1;
u16 grpsel_off = (regs == 3) ?
OMAP3430ES2_PM_MPUGRPSEL3 : OMAP3430_PM_MPUGRPSEL;
int c = 0;
wkst = omap2_prm_read_mod_reg(module, wkst_off);
wkst &= omap2_prm_read_mod_reg(module, grpsel_off);
if (wkst) {
iclk = omap2_cm_read_mod_reg(module, iclk_off);
fclk = omap2_cm_read_mod_reg(module, fclk_off);
while (wkst) {
clken = wkst;
omap2_cm_set_mod_reg_bits(clken, module, iclk_off);
/*
* For USBHOST, we don't know whether HOST1 or
* HOST2 woke us up, so enable both f-clocks
*/
if (module == OMAP3430ES2_USBHOST_MOD)
clken |= 1 << OMAP3430ES2_EN_USBHOST2_SHIFT;
omap2_cm_set_mod_reg_bits(clken, module, fclk_off);
omap2_prm_write_mod_reg(wkst, module, wkst_off);
wkst = omap2_prm_read_mod_reg(module, wkst_off);
c++;
}
omap2_cm_write_mod_reg(iclk, module, iclk_off);
omap2_cm_write_mod_reg(fclk, module, fclk_off);
}
return c;
}
static void omap2_enter_mpu_retention(void)
{
int only_idle = 0;
struct timespec ts_preidle, ts_postidle, ts_idle;
/* Putting MPU into the WFI state while a transfer is active
* seems to cause the I2C block to timeout. Why? Good question. */
if (omap2_i2c_active())
return;
/* The peripherals seem not to be able to wake up the MPU when
* it is in retention mode. */
if (omap2_allow_mpu_retention()) {
/* REVISIT: These write to reserved bits? */
omap2_prm_write_mod_reg(0xffffffff, CORE_MOD, PM_WKST1);
omap2_prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP24XX_PM_WKST2);
omap2_prm_write_mod_reg(0xffffffff, WKUP_MOD, PM_WKST);
/* Try to enter MPU retention */
omap2_prm_write_mod_reg((0x01 << OMAP_POWERSTATE_SHIFT) |
OMAP_LOGICRETSTATE_MASK,
MPU_MOD, OMAP2_PM_PWSTCTRL);
} else {
/* Block MPU retention */
omap2_prm_write_mod_reg(OMAP_LOGICRETSTATE_MASK, MPU_MOD,
OMAP2_PM_PWSTCTRL);
only_idle = 1;
}
if (omap2_pm_debug) {
omap2_pm_dump(only_idle ? 2 : 1, 0, 0);
getnstimeofday(&ts_preidle);
}
omap2_sram_idle();
if (omap2_pm_debug) {
unsigned long long tmp;
getnstimeofday(&ts_postidle);
ts_idle = timespec_sub(ts_postidle, ts_preidle);
tmp = timespec_to_ns(&ts_idle) * NSEC_PER_USEC;
omap2_pm_dump(only_idle ? 2 : 1, 1, tmp);
}
}
static int omap2_enter_full_retention(void)
{
u32 l;
clk_disable(osc_ck);
omap2_prm_write_mod_reg(0xffffffff, CORE_MOD, PM_WKST1);
omap2_prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP24XX_PM_WKST2);
omap2_prm_write_mod_reg(0xffffffff, WKUP_MOD, PM_WKST);
pwrdm_set_logic_retst(mpu_pwrdm, PWRDM_POWER_RET);
pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_RET);
l = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0) | OMAP24XX_USBSTANDBYCTRL;
omap_ctrl_writel(l, OMAP2_CONTROL_DEVCONF0);
omap2_gpio_prepare_for_idle(0);
if (omap_irq_pending())
goto no_sleep;
omap2_sram_suspend(sdrc_read_reg(SDRC_DLLA_CTRL),
OMAP_SDRC_REGADDR(SDRC_DLLA_CTRL),
OMAP_SDRC_REGADDR(SDRC_POWER));
no_sleep:
omap2_gpio_resume_after_idle();
clk_enable(osc_ck);
omap2_prm_write_mod_reg(0xffffffff, CORE_MOD, PM_WKST1);
omap2_prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP24XX_PM_WKST2);
omap2_prm_clear_mod_reg_bits(0x4 | 0x1, WKUP_MOD, PM_WKST);
l = omap2_prm_read_mod_reg(OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
if (l & 0x01)
omap2_prm_write_mod_reg(0x01, OCP_MOD,
OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
if (l & 0x20)
omap2_prm_write_mod_reg(0x20, OCP_MOD,
OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
omap2_prm_write_mod_reg(0x0, OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
return 0;
}
static int omap2_pm_suspend(void)
{
u32 wken_wkup, mir1;
wken_wkup = omap2_prm_read_mod_reg(WKUP_MOD, PM_WKEN);
wken_wkup &= ~OMAP24XX_EN_GPT1_MASK;
omap2_prm_write_mod_reg(wken_wkup, WKUP_MOD, PM_WKEN);
/* Mask GPT1 */
mir1 = omap_readl(0x480fe0a4);
omap_writel(1 << 5, 0x480fe0ac);
omap_uart_prepare_suspend();
omap2_enter_full_retention();
omap_writel(mir1, 0x480fe0a4);
omap2_prm_write_mod_reg(wken_wkup, WKUP_MOD, PM_WKEN);
return 0;
}
/* Read-modify-write a register in a PRM module. Caller must lock */
u32 omap2_prm_rmw_mod_reg_bits(u32 mask, u32 bits, s16 module, s16 idx)
{
u32 v;
v = omap2_prm_read_mod_reg(module, idx);
v &= ~mask;
v |= bits;
omap2_prm_write_mod_reg(v, module, idx);
return v;
}
/*
* PRCM Interrupt Handler
*
* The PRM_IRQSTATUS_MPU register indicates if there are any pending
* interrupts from the PRCM for the MPU. These bits must be cleared in
* order to clear the PRCM interrupt. The PRCM interrupt handler is
* implemented to simply clear the PRM_IRQSTATUS_MPU in order to clear
* the PRCM interrupt. Please note that bit 0 of the PRM_IRQSTATUS_MPU
* register indicates that a wake-up event is pending for the MPU and
* this bit can only be cleared if the all the wake-up events latched
* in the various PM_WKST_x registers have been cleared. The interrupt
* handler is implemented using a do-while loop so that if a wake-up
* event occurred during the processing of the prcm interrupt handler
* (setting a bit in the corresponding PM_WKST_x register and thus
* preventing us from clearing bit 0 of the PRM_IRQSTATUS_MPU register)
* this would be handled.
*/
static irqreturn_t prcm_interrupt_handler (int irq, void *dev_id)
{
u32 irqenable_mpu, irqstatus_mpu;
int c = 0;
irqenable_mpu = omap2_prm_read_mod_reg(OCP_MOD,
OMAP3_PRM_IRQENABLE_MPU_OFFSET);
irqstatus_mpu = omap2_prm_read_mod_reg(OCP_MOD,
OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
irqstatus_mpu &= irqenable_mpu;
do {
if (irqstatus_mpu & (OMAP3430_WKUP_ST_MASK |
OMAP3430_IO_ST_MASK)) {
c = _prcm_int_handle_wakeup();
/*
* Is the MPU PRCM interrupt handler racing with the
* IVA2 PRCM interrupt handler ?
*/
WARN(c == 0, "prcm: WARNING: PRCM indicated MPU wakeup "
"but no wakeup sources are marked\n");
} else {
/* XXX we need to expand our PRCM interrupt handler */
WARN(1, "prcm: WARNING: PRCM interrupt received, but "
"no code to handle it (%08x)\n", irqstatus_mpu);
}
omap2_prm_write_mod_reg(irqstatus_mpu, OCP_MOD,
OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
irqstatus_mpu = omap2_prm_read_mod_reg(OCP_MOD,
OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
irqstatus_mpu &= irqenable_mpu;
} while (irqstatus_mpu);
return IRQ_HANDLED;
}
static void omap2_enter_full_retention(void)
{
u32 l;
struct timespec ts_preidle, ts_postidle, ts_idle;
/* There is 1 reference hold for all children of the oscillator
* clock, the following will remove it. If no one else uses the
* oscillator itself it will be disabled if/when we enter retention
* mode.
*/
clk_disable(osc_ck);
/* Clear old wake-up events */
/* REVISIT: These write to reserved bits? */
omap2_prm_write_mod_reg(0xffffffff, CORE_MOD, PM_WKST1);
omap2_prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP24XX_PM_WKST2);
omap2_prm_write_mod_reg(0xffffffff, WKUP_MOD, PM_WKST);
/*
* Set MPU powerdomain's next power state to RETENTION;
* preserve logic state during retention
*/
pwrdm_set_logic_retst(mpu_pwrdm, PWRDM_POWER_RET);
pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_RET);
/* Workaround to kill USB */
l = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0) | OMAP24XX_USBSTANDBYCTRL;
omap_ctrl_writel(l, OMAP2_CONTROL_DEVCONF0);
omap2_gpio_prepare_for_idle(0);
if (omap2_pm_debug) {
omap2_pm_dump(0, 0, 0);
getnstimeofday(&ts_preidle);
}
/* One last check for pending IRQs to avoid extra latency due
* to sleeping unnecessarily. */
if (omap_irq_pending())
goto no_sleep;
/* Block console output in case it is on one of the OMAP UARTs */
if (!is_suspending())
if (!console_trylock())
goto no_sleep;
omap_uart_prepare_idle(0);
omap_uart_prepare_idle(1);
omap_uart_prepare_idle(2);
/* Jump to SRAM suspend code */
omap2_sram_suspend(sdrc_read_reg(SDRC_DLLA_CTRL),
OMAP_SDRC_REGADDR(SDRC_DLLA_CTRL),
OMAP_SDRC_REGADDR(SDRC_POWER));
omap_uart_resume_idle(2);
omap_uart_resume_idle(1);
omap_uart_resume_idle(0);
if (!is_suspending())
console_unlock();
no_sleep:
if (omap2_pm_debug) {
unsigned long long tmp;
getnstimeofday(&ts_postidle);
ts_idle = timespec_sub(ts_postidle, ts_preidle);
tmp = timespec_to_ns(&ts_idle) * NSEC_PER_USEC;
omap2_pm_dump(0, 1, tmp);
}
omap2_gpio_resume_after_idle();
clk_enable(osc_ck);
/* clear CORE wake-up events */
omap2_prm_write_mod_reg(0xffffffff, CORE_MOD, PM_WKST1);
omap2_prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP24XX_PM_WKST2);
/* wakeup domain events - bit 1: GPT1, bit5 GPIO */
omap2_prm_clear_mod_reg_bits(0x4 | 0x1, WKUP_MOD, PM_WKST);
/* MPU domain wake events */
l = omap2_prm_read_mod_reg(OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
if (l & 0x01)
omap2_prm_write_mod_reg(0x01, OCP_MOD,
OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
if (l & 0x20)
omap2_prm_write_mod_reg(0x20, OCP_MOD,
OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
/* Mask future PRCM-to-MPU interrupts */
omap2_prm_write_mod_reg(0x0, OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
}
static void __init prcm_setup_regs(void)
{
int i, num_mem_banks;
struct powerdomain *pwrdm;
/*
* Enable autoidle
* XXX This should be handled by hwmod code or PRCM init code
*/
omap2_prm_write_mod_reg(OMAP24XX_AUTOIDLE_MASK, OCP_MOD,
OMAP2_PRCM_SYSCONFIG_OFFSET);
/*
* Set CORE powerdomain memory banks to retain their contents
* during RETENTION
*/
num_mem_banks = pwrdm_get_mem_bank_count(core_pwrdm);
for (i = 0; i < num_mem_banks; i++)
pwrdm_set_mem_retst(core_pwrdm, i, PWRDM_POWER_RET);
/* Set CORE powerdomain's next power state to RETENTION */
pwrdm_set_next_pwrst(core_pwrdm, PWRDM_POWER_RET);
/*
* Set MPU powerdomain's next power state to RETENTION;
* preserve logic state during retention
*/
pwrdm_set_logic_retst(mpu_pwrdm, PWRDM_POWER_RET);
pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_RET);
/* Force-power down DSP, GFX powerdomains */
pwrdm = clkdm_get_pwrdm(dsp_clkdm);
pwrdm_set_next_pwrst(pwrdm, PWRDM_POWER_OFF);
clkdm_sleep(dsp_clkdm);
pwrdm = clkdm_get_pwrdm(gfx_clkdm);
pwrdm_set_next_pwrst(pwrdm, PWRDM_POWER_OFF);
clkdm_sleep(gfx_clkdm);
/* Enable hardware-supervised idle for all clkdms */
clkdm_for_each(clkdms_setup, NULL);
clkdm_add_wkdep(mpu_clkdm, wkup_clkdm);
/* REVISIT: Configure number of 32 kHz clock cycles for sys_clk
* stabilisation */
omap2_prm_write_mod_reg(15 << OMAP_SETUP_TIME_SHIFT, OMAP24XX_GR_MOD,
OMAP2_PRCM_CLKSSETUP_OFFSET);
/* Configure automatic voltage transition */
omap2_prm_write_mod_reg(2 << OMAP_SETUP_TIME_SHIFT, OMAP24XX_GR_MOD,
OMAP2_PRCM_VOLTSETUP_OFFSET);
omap2_prm_write_mod_reg(OMAP24XX_AUTO_EXTVOLT_MASK |
(0x1 << OMAP24XX_SETOFF_LEVEL_SHIFT) |
OMAP24XX_MEMRETCTRL_MASK |
(0x1 << OMAP24XX_SETRET_LEVEL_SHIFT) |
(0x0 << OMAP24XX_VOLT_LEVEL_SHIFT),
OMAP24XX_GR_MOD, OMAP2_PRCM_VOLTCTRL_OFFSET);
/* Enable wake-up events */
omap2_prm_write_mod_reg(OMAP24XX_EN_GPIOS_MASK | OMAP24XX_EN_GPT1_MASK,
WKUP_MOD, PM_WKEN);
}
static int omap2_enter_full_retention(void)
{
u32 l;
/* There is 1 reference hold for all children of the oscillator
* clock, the following will remove it. If no one else uses the
* oscillator itself it will be disabled if/when we enter retention
* mode.
*/
clk_disable(osc_ck);
/* Clear old wake-up events */
/* REVISIT: These write to reserved bits? */
omap2_prm_write_mod_reg(0xffffffff, CORE_MOD, PM_WKST1);
omap2_prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP24XX_PM_WKST2);
omap2_prm_write_mod_reg(0xffffffff, WKUP_MOD, PM_WKST);
/*
* Set MPU powerdomain's next power state to RETENTION;
* preserve logic state during retention
*/
pwrdm_set_logic_retst(mpu_pwrdm, PWRDM_POWER_RET);
pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_RET);
/* Workaround to kill USB */
l = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0) | OMAP24XX_USBSTANDBYCTRL;
omap_ctrl_writel(l, OMAP2_CONTROL_DEVCONF0);
omap2_gpio_prepare_for_idle(0);
/* One last check for pending IRQs to avoid extra latency due
* to sleeping unnecessarily. */
if (omap_irq_pending())
goto no_sleep;
/* Jump to SRAM suspend code */
omap2_sram_suspend(sdrc_read_reg(SDRC_DLLA_CTRL),
OMAP_SDRC_REGADDR(SDRC_DLLA_CTRL),
OMAP_SDRC_REGADDR(SDRC_POWER));
no_sleep:
omap2_gpio_resume_after_idle();
clk_enable(osc_ck);
/* clear CORE wake-up events */
omap2_prm_write_mod_reg(0xffffffff, CORE_MOD, PM_WKST1);
omap2_prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP24XX_PM_WKST2);
/* wakeup domain events - bit 1: GPT1, bit5 GPIO */
omap2_prm_clear_mod_reg_bits(0x4 | 0x1, WKUP_MOD, PM_WKST);
/* MPU domain wake events */
l = omap2_prm_read_mod_reg(OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
if (l & 0x01)
omap2_prm_write_mod_reg(0x01, OCP_MOD,
OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
if (l & 0x20)
omap2_prm_write_mod_reg(0x20, OCP_MOD,
OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
/* Mask future PRCM-to-MPU interrupts */
omap2_prm_write_mod_reg(0x0, OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
return 0;
}
static void __init prcm_setup_regs(void)
{
int i, num_mem_banks;
struct powerdomain *pwrdm;
/* Enable autoidle */
omap2_prm_write_mod_reg(OMAP24XX_AUTOIDLE_MASK, OCP_MOD,
OMAP2_PRCM_SYSCONFIG_OFFSET);
/*
* Set CORE powerdomain memory banks to retain their contents
* during RETENTION
*/
num_mem_banks = pwrdm_get_mem_bank_count(core_pwrdm);
for (i = 0; i < num_mem_banks; i++)
pwrdm_set_mem_retst(core_pwrdm, i, PWRDM_POWER_RET);
/* Set CORE powerdomain's next power state to RETENTION */
pwrdm_set_next_pwrst(core_pwrdm, PWRDM_POWER_RET);
/*
* Set MPU powerdomain's next power state to RETENTION;
* preserve logic state during retention
*/
pwrdm_set_logic_retst(mpu_pwrdm, PWRDM_POWER_RET);
pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_RET);
/* Force-power down DSP, GFX powerdomains */
pwrdm = clkdm_get_pwrdm(dsp_clkdm);
pwrdm_set_next_pwrst(pwrdm, PWRDM_POWER_OFF);
omap2_clkdm_sleep(dsp_clkdm);
pwrdm = clkdm_get_pwrdm(gfx_clkdm);
pwrdm_set_next_pwrst(pwrdm, PWRDM_POWER_OFF);
omap2_clkdm_sleep(gfx_clkdm);
/*
* Clear clockdomain wakeup dependencies and enable
* hardware-supervised idle for all clkdms
*/
clkdm_for_each(clkdms_setup, NULL);
clkdm_add_wkdep(mpu_clkdm, wkup_clkdm);
/* Enable clock autoidle for all domains */
omap2_cm_write_mod_reg(OMAP24XX_AUTO_CAM_MASK |
OMAP24XX_AUTO_MAILBOXES_MASK |
OMAP24XX_AUTO_WDT4_MASK |
OMAP2420_AUTO_WDT3_MASK |
OMAP24XX_AUTO_MSPRO_MASK |
OMAP2420_AUTO_MMC_MASK |
OMAP24XX_AUTO_FAC_MASK |
OMAP2420_AUTO_EAC_MASK |
OMAP24XX_AUTO_HDQ_MASK |
OMAP24XX_AUTO_UART2_MASK |
OMAP24XX_AUTO_UART1_MASK |
OMAP24XX_AUTO_I2C2_MASK |
OMAP24XX_AUTO_I2C1_MASK |
OMAP24XX_AUTO_MCSPI2_MASK |
OMAP24XX_AUTO_MCSPI1_MASK |
OMAP24XX_AUTO_MCBSP2_MASK |
OMAP24XX_AUTO_MCBSP1_MASK |
OMAP24XX_AUTO_GPT12_MASK |
OMAP24XX_AUTO_GPT11_MASK |
OMAP24XX_AUTO_GPT10_MASK |
OMAP24XX_AUTO_GPT9_MASK |
OMAP24XX_AUTO_GPT8_MASK |
OMAP24XX_AUTO_GPT7_MASK |
OMAP24XX_AUTO_GPT6_MASK |
OMAP24XX_AUTO_GPT5_MASK |
OMAP24XX_AUTO_GPT4_MASK |
OMAP24XX_AUTO_GPT3_MASK |
OMAP24XX_AUTO_GPT2_MASK |
OMAP2420_AUTO_VLYNQ_MASK |
OMAP24XX_AUTO_DSS_MASK,
CORE_MOD, CM_AUTOIDLE1);
omap2_cm_write_mod_reg(OMAP24XX_AUTO_UART3_MASK |
OMAP24XX_AUTO_SSI_MASK |
OMAP24XX_AUTO_USB_MASK,
CORE_MOD, CM_AUTOIDLE2);
omap2_cm_write_mod_reg(OMAP24XX_AUTO_SDRC_MASK |
OMAP24XX_AUTO_GPMC_MASK |
OMAP24XX_AUTO_SDMA_MASK,
CORE_MOD, CM_AUTOIDLE3);
omap2_cm_write_mod_reg(OMAP24XX_AUTO_PKA_MASK |
OMAP24XX_AUTO_AES_MASK |
OMAP24XX_AUTO_RNG_MASK |
OMAP24XX_AUTO_SHA_MASK |
OMAP24XX_AUTO_DES_MASK,
CORE_MOD, OMAP24XX_CM_AUTOIDLE4);
omap2_cm_write_mod_reg(OMAP2420_AUTO_DSP_IPI_MASK, OMAP24XX_DSP_MOD,
CM_AUTOIDLE);
/* Put DPLL and both APLLs into autoidle mode */
omap2_cm_write_mod_reg((0x03 << OMAP24XX_AUTO_DPLL_SHIFT) |
(0x03 << OMAP24XX_AUTO_96M_SHIFT) |
(0x03 << OMAP24XX_AUTO_54M_SHIFT),
PLL_MOD, CM_AUTOIDLE);
omap2_cm_write_mod_reg(OMAP24XX_AUTO_OMAPCTRL_MASK |
OMAP24XX_AUTO_WDT1_MASK |
OMAP24XX_AUTO_MPU_WDT_MASK |
OMAP24XX_AUTO_GPIOS_MASK |
OMAP24XX_AUTO_32KSYNC_MASK |
OMAP24XX_AUTO_GPT1_MASK,
WKUP_MOD, CM_AUTOIDLE);
/* REVISIT: Configure number of 32 kHz clock cycles for sys_clk
* stabilisation */
omap2_prm_write_mod_reg(15 << OMAP_SETUP_TIME_SHIFT, OMAP24XX_GR_MOD,
OMAP2_PRCM_CLKSSETUP_OFFSET);
/* Configure automatic voltage transition */
omap2_prm_write_mod_reg(2 << OMAP_SETUP_TIME_SHIFT, OMAP24XX_GR_MOD,
OMAP2_PRCM_VOLTSETUP_OFFSET);
omap2_prm_write_mod_reg(OMAP24XX_AUTO_EXTVOLT_MASK |
(0x1 << OMAP24XX_SETOFF_LEVEL_SHIFT) |
OMAP24XX_MEMRETCTRL_MASK |
(0x1 << OMAP24XX_SETRET_LEVEL_SHIFT) |
(0x0 << OMAP24XX_VOLT_LEVEL_SHIFT),
OMAP24XX_GR_MOD, OMAP2_PRCM_VOLTCTRL_OFFSET);
/* Enable wake-up events */
omap2_prm_write_mod_reg(OMAP24XX_EN_GPIOS_MASK | OMAP24XX_EN_GPT1_MASK,
WKUP_MOD, PM_WKEN);
}
static int omap3_pwrdm_clear_all_prev_pwrst(struct powerdomain *pwrdm)
{
omap2_prm_write_mod_reg(0, pwrdm->prcm_offs, OMAP3430_PM_PREPWSTST);
return 0;
}
static void omap3_voltage_write_reg(u32 val, u16 mod, u8 offset)
{
omap2_prm_write_mod_reg(val, mod, offset);
}
