static int __init omap2_init_devices(void)
{
/* Enable dummy states for those platforms without pinctrl support */
if (!of_have_populated_dt())
pinctrl_provide_dummies();
/*
* please keep these calls, and their implementations above,
* in alphabetical order so they're easier to sort through.
*/
omap_init_audio();
omap_init_camera();
omap_init_hdmi_audio();
omap_init_mbox();
/* If dtb is there, the devices will be created dynamically */
if (!of_have_populated_dt()) {
omap_init_dmic();
omap_init_mcpdm();
omap_init_mcspi();
omap_init_sham();
omap_init_aes();
} else {
/* These can be removed when bindings are done */
omap_init_wl12xx_of();
}
omap_init_sti();
omap_init_rng();
omap_init_vout();
return 0;
}
static int __init omap2_init_devices(void)
{
/* Enable dummy states for those platforms without pinctrl support */
if (!of_have_populated_dt())
pinctrl_provide_dummies();
/*
* please keep these calls, and their implementations above,
* in alphabetical order so they're easier to sort through.
*/
omap_init_audio();
omap_init_camera();
omap_init_hdmi_audio();
omap_init_mbox();
/* If dtb is there, the devices will be created dynamically */
if (!of_have_populated_dt()) {
omap_init_dmic();
omap_init_mcpdm();
omap_init_mcspi();
omap_init_sham();
omap_init_aes();
}
omap_init_sti();
omap_init_rng();
omap_init_vout();
omap_init_ocp2scp();
if (soc_is_am33xx()) {
am33xx_register_ehrpwm();
}
return 0;
}
static int __init omap2_init_devices(void)
{
/*
* please keep these calls, and their implementations above,
* in alphabetical order so they're easier to sort through.
*/
omap_init_audio();
omap_init_mcpdm();
omap_init_dmic();
omap_init_camera();
omap_init_mbox();
omap_init_mcspi();
omap_init_pmu();
omap_hdq_init();
omap_init_sti();
omap_init_sham();
omap_init_aes();
omap_init_vout();
am33xx_register_edma();
am33xx_init_pcm();
#if defined (CONFIG_SOC_OMAPAM33XX)
am335x_register_pruss_uio(&am335x_pruss_uio_pdata);
if (omap3_has_sgx())
platform_device_register(&am335x_sgx);
#endif
return 0;
}
static int __init omap2_init_devices(void)
{
/*
* please keep these calls, and their implementations above,
* in alphabetical order so they're easier to sort through.
*/
omap_init_audio();
omap_init_camera();
omap_init_hdmi_audio();
omap_init_mbox();
/* If dtb is there, the devices will be created dynamically */
if (!of_have_populated_dt()) {
omap_init_dmic();
omap_init_mcpdm();
omap_init_mcspi();
}
omap_init_pmu();
omap_hdq_init();
omap_init_sti();
omap_init_sham();
omap_init_aes();
omap_init_vout();
return 0;
}
/*
* This gets called after board-specific INIT_MACHINE, and initializes most
* on-chip peripherals accessible on this board (except for few like USB):
*
* (a) Does any "standard config" pin muxing needed. Board-specific
* code will have muxed GPIO pins and done "nonstandard" setup;
* that code could live in the boot loader.
* (b) Populating board-specific platform_data with the data drivers
* rely on to handle wiring variations.
* (c) Creating platform devices as meaningful on this board and
* with this kernel configuration.
*
* Claiming GPIOs, and setting their direction and initial values, is the
* responsibility of the device drivers. So is responding to probe().
*
* Board-specific knowledge like creating devices or pin setup is to be
* kept out of drivers as much as possible. In particular, pin setup
* may be handled by the boot loader, and drivers should expect it will
* normally have been done by the time they're probed.
*/
static int __init omap_init_devices(void)
{
/* please keep these calls, and their implementations above,
* in alphabetical order so they're easier to sort through.
*/
omap_init_rng();
omap_init_dmic();
omap_init_uwire();
return 0;
}
static int __init omap2_init_devices(void)
{
omap_init_audio();
omap_init_mcpdm();
omap_init_dmic();
omap_init_camera();
omap_init_mbox();
omap_init_mcspi();
omap_init_pmu();
omap_hdq_init();
omap_init_sti();
omap_init_sham();
omap_init_aes();
omap_init_vout();
return 0;
}
static int __init omap2_init_devices(void)
{
/*
* please keep these calls, and their implementations above,
* in alphabetical order so they're easier to sort through.
*/
omap_init_audio();
omap_init_mcpdm();
omap_init_dmic();
omap_init_camera();
omap_init_mbox();
omap_init_mcspi();
omap_init_pmu();
omap_hdq_init();
omap_init_sti();
omap_init_sham();
omap_init_aes();
omap_init_vout();
return 0;
}
