int omap_usb2_charger_detect(struct phy_companion *comparator)
{
struct usb_phy *x = usb_get_phy(USB_PHY_TYPE_USB2);
struct omap_usb *phy = phy_to_omapusb(x);
int charger = 0;
omap_usb2_suspend(x, 0);
charger = omap_usb_charger_detect(phy->control_dev);
omap_usb2_suspend(x, 1);
return charger;
}
int __devinit dwc3_probe(struct platform_device *pdev)
{
struct dwc3 *dwc;
#if !defined(CONFIG_DRA7XX)
u8 vali;
#endif
int ret = -ENOMEM;
void __iomem *regs;
void *mem;
u8 mode;
/* Initialize all the clocks (system clocks/ optional clocks etc) */
/* USB_OTG_SS_CLKSTCTRL */
writel(USB_OTG_SS_OPTFCLKEN_REFCLK960M | USB_OTG_SS_MODULEMODE_HW,
CM_L3INIT_USB_OTG_SS_CLKCTRL);
/* OCP2SCP1 register for PHY register access */
writel(OCP2SCP1_MODULEMODE_HW, CM_L3INIT_OCP2SCP1_CLKCTRL);
/* Turn on 32K AON clk */
writel(USB_PHY_CORE_OPTFCLKEN_CLK32K, CM_COREAON_USB_PHY_CORE_CLKCTRL);
/* Setting CM_L3INIT_CLKSTCTRL to NO sleep */
writel(L3INIT_CLKSTCTRL_NOSLEEP, CM_L3INIT_CLKSTCTRL);
/* Setting USBOTGSS_SYSCONFIG to NO idle */
writel((SYSCONFIG_DMADISABLE | SYSCONFIG_STANDBY_SMART | SYSCONFIG_IDLEMODE),
USBOTGSS_SYSCONFIG);
/* Initialize the wrapper registers */
dwc3_wrapper_init();
mem = kzalloc(sizeof(*dwc) + DWC3_ALIGN_MASK, GFP_KERNEL);
if (!mem) {
dev_err(&pdev->dev, "not enough memory\n");
goto err0;
}
dwc = PTR_ALIGN(mem, DWC3_ALIGN_MASK + 1);
dwc->mem = mem;
global_dwc3 = dwc;
dwc->regs = CONFIG_USB_DWC3_UDC_REGS;
dwc->regs_size = DWC3_USB_REGS_SIZE;
dwc->dev = &pdev->dev;
if (!strncmp("super", maximum_speed, 5))
dwc->maximum_speed = DWC3_DCFG_SUPERSPEED;
else if (!strncmp("high", maximum_speed, 4))
dwc->maximum_speed = DWC3_DCFG_HIGHSPEED;
else if (!strncmp("full", maximum_speed, 4))
dwc->maximum_speed = DWC3_DCFG_FULLSPEED1;
else if (!strncmp("low", maximum_speed, 3))
dwc->maximum_speed = DWC3_DCFG_LOWSPEED;
else
dwc->maximum_speed = DWC3_DCFG_SUPERSPEED;
pm_runtime_enable(&pdev->dev);
pm_runtime_get_sync(&pdev->dev);
pm_runtime_forbid(&pdev->dev);
dwc3_cache_hwparams(dwc);
ret = dwc3_alloc_event_buffers(dwc, DWC3_EVENT_BUFFERS_SIZE);
if (ret) {
dev_err(&pdev->dev, "failed to initialize core\n");
goto err3;
}
omap_usb2_suspend(0);
omap_usb3_suspend(0);
ret = dwc3_core_init(dwc);
if (ret) {
dev_err(dev, "failed to initialize core\n");
goto err0;
}
mode = DWC3_MODE_DEVICE /*DWC3_MODE(dwc->hwparams.hwparams0)*/;
switch (mode) {
case DWC3_MODE_DEVICE:
dwc3_set_mode(dwc, DWC3_GCTL_PRTCAP_DEVICE);
ret = dwc3_gadget_init(dwc);
if (ret) {
dev_err(&pdev->dev, "failed to initialize gadget\n");
goto err4;
}
break;
case DWC3_MODE_HOST:
dwc3_set_mode(dwc, DWC3_GCTL_PRTCAP_HOST);
ret = dwc3_host_init(dwc);
if (ret) {
dev_err(&pdev->dev, "failed to initialize host\n");
goto err4;
}
break;
case DWC3_MODE_DRD:
dwc3_set_mode(dwc, DWC3_GCTL_PRTCAP_OTG);
ret = dwc3_host_init(dwc);
if (ret) {
dev_err(&pdev->dev, "failed to initialize host\n");
goto err4;
}
ret = dwc3_gadget_init(dwc);
if (ret) {
dev_err(&pdev->dev, "failed to initialize gadget\n");
goto err4;
}
break;
default:
dev_err(&pdev->dev, "Unsupported mode of operation %d\n", mode);
goto err4;
}
dwc->mode = mode;
#if !defined(CONFIG_DRA7XX)
/* Enable the VBUS comparator in the palmas chip */
palmas_i2c_read_u8(0x49, 0x1C, &vali);
palmas_i2c_write_u8(0x49, 0x53, 0x1);
/* Wait for the vbus line state interrupt */
do {
palmas_i2c_read_u8(0x49, 0x1C, &vali);
} while (!(vali & 0x80));
#endif
return 0;
err4:
dwc3_core_exit(dwc);
err3:
iounmap(regs);
kfree(dwc->mem);
err0:
return ret;
}