/* Charging power state initialization */
int charger_post_init(void)
{
int rv, option;
#ifdef CONFIG_CHARGER_ILIM_PIN_DISABLED
int option2;
#endif
rv = charger_get_option(&option);
if (rv)
return rv;
option &= ~OPTION0_LEARN_ENABLE;
rv = charger_set_option(option);
if (rv)
return rv;
#ifndef BOARD_SAMUS
/* Turn off PROCHOT warning */
rv = raw_read16(REG_PROCHOT_OPTION1, &option);
if (rv)
return rv;
option &= ~PROCHOT_OPTION1_SELECTOR_MASK;
rv = raw_write16(REG_PROCHOT_OPTION1, option);
#else
/* On Samus, use PROCHOT warning to detect charging problems */
/* Turn on PROCHOT warning */
rv = raw_write16(REG_PROCHOT_OPTION1, 0x8120);
/* Set PROCHOT ICRIT warning when IADP is >120% of IDPM */
rv |= raw_write16(REG_PROCHOT_OPTION0, 0x1b54);
#endif
if (rv)
return rv;
#ifdef CONFIG_CHARGER_ILIM_PIN_DISABLED
/* Read the external ILIM pin enabled flag. */
rv = raw_read16(REG_CHARGE_OPTION2, &option2);
if (rv)
return rv;
/* Set ILIM pin disabled if it is currently enabled. */
if (option2 & OPTION2_EN_EXTILIM) {
option2 &= ~OPTION2_EN_EXTILIM;
rv = raw_write16(REG_CHARGE_OPTION2, option2);
}
return rv;
#else
return EC_SUCCESS;
#endif
}
int charger_device_id(int *id)
{
#ifdef CONFIG_CHARGER_BQ24770
return raw_read16(REG_DEVICE_ADDRESS, id);
#elif defined(CONFIG_CHARGER_BQ24773)
return raw_read8(REG_DEVICE_ADDRESS, id);
#endif
}
int charger_manufacturer_id(int *id)
{
#ifdef CONFIG_CHARGER_BQ24770
return raw_read16(REG_MANUFACTURE_ID, id);
#elif defined(CONFIG_CHARGER_BQ24773)
*id = 0x40; /* TI */
return EC_SUCCESS;
#endif
}
int charger_get_current(int *current)
{
int rv;
int reg;
rv = raw_read16(REG_CHARGE_CURRENT, ®);
if (rv)
return rv;
*current = REG_TO_CURRENT(reg, R_SNS);
return EC_SUCCESS;
}
int charger_get_input_current(int *input_current)
{
int rv;
int reg;
#ifdef CONFIG_CHARGER_BQ24770
rv = raw_read16(REG_INPUT_CURRENT, ®);
#elif defined(CONFIG_CHARGER_BQ24773)
rv = raw_read8(REG_INPUT_CURRENT, ®);
#endif
if (rv)
return rv;
#ifdef CONFIG_CHARGER_BQ24770
*input_current = REG_TO_CURRENT(reg, R_AC);
#elif defined(CONFIG_CHARGER_BQ24773)
*input_current = REG8_TO_CURRENT(reg, R_AC);
#endif
return EC_SUCCESS;
}
static int si114x_read_results(struct motion_sensor_t *s, int nb)
{
int i, ret, val;
struct si114x_drv_data_t *data = SI114X_GET_DATA(s);
struct si114x_typed_data_t *type_data = SI114X_GET_TYPED_DATA(s);
#ifdef CONFIG_ACCEL_FIFO
struct ec_response_motion_sensor_data vector;
#endif
/* Read ALX result */
for (i = 0; i < nb; i++) {
ret = raw_read16(s->port, s->addr,
type_data->base_data_reg + i * 2,
&val);
if (ret)
break;
/* Add offset, calibration */
if (val + type_data->offset <= 0) {
val = 1;
} else if (val != SI114X_OVERFLOW) {
val += type_data->offset;
/*
* Proxmitiy sensor data is inverse of the distance.
* Return back something proportional to distance,
* we affine with the scale parmeter.
*/
if (s->type == MOTIONSENSE_TYPE_PROX)
val = SI114X_PS_INVERSION(val);
val = val * type_data->scale +
val * type_data->uscale / 10000;
}
s->raw_xyz[i] = val;
}
if (ret != EC_SUCCESS)
return ret;
if (s->type == MOTIONSENSE_TYPE_PROX)
data->covered = (s->raw_xyz[0] < SI114X_COVERED_THRESHOLD);
else if (data->covered)
/*
* The sensor (proximity & light) is covered. The light data
* will most likely be incorrect (darker than expected), so
* ignore the measurement.
*/
return EC_SUCCESS;
/* Add in fifo if changed only */
for (i = 0; i < nb; i++) {
if (s->raw_xyz[i] != s->xyz[i])
break;
}
if (i == nb)
return EC_SUCCESS;
#ifdef CONFIG_ACCEL_FIFO
vector.flags = 0;
for (i = 0; i < nb; i++)
vector.data[i] = s->raw_xyz[i];
for (i = nb; i < 3; i++)
vector.data[i] = 0;
vector.sensor_num = s - motion_sensors;
motion_sense_fifo_add_unit(&vector, s, nb);
#else
/* We need to copy raw_xyz into xyz with mutex */
#endif
return EC_SUCCESS;
}
int charger_get_option(int *option)
{
return raw_read16(REG_CHARGE_OPTION0, option);
}
int charger_get_voltage(int *voltage)
{
return raw_read16(REG_MAX_CHARGE_VOLTAGE, voltage);
}
