Beispiel #1
0
void check_factory_uart1 (void)
{
	uint8_t * buf_ptr;

	buf_ptr = getUSART1buf();

	if(strncmp(buf_ptr, FACTORY_CHECK_STR, sizeof(FACTORY_CHECK_STR)) == 0)
	{
		// Serial data buffer clear
		USART1_flush();

		factory_test_2nd();

#if defined(FACTORY_FW_FLASH)
		release_factory_flag();
#else
		//g_factoryfw_flag = 0;
#endif

		//delay_ms(200);
		//NVIC_SystemReset();
	}
}
Beispiel #2
0
int main(void) {
	uint8_t ret = 0;
    //int32_t loopback_ret;

#if defined (__USE_LPCOPEN)
#if !defined(NO_BOARD_LIB)
    // Read clock settings and update SystemCoreClock variable
    SystemCoreClockUpdate();
    // Set up and initialize all required blocks and
    // functions related to the board hardware
    Board_Init();
    // Set the LED to the state of "On"
    Board_LED_Set(0, true);
    //Board_LED_Set(1, true);
    //Board_LED_Set(2, true);
#endif
#endif

	SPI_Init();
	W5500_Init();
	Net_Conf(gWIZNETINFO);

#ifdef _MAIN_DEBUG_
	uint8_t tmpstr[6] = {0,};

	ctlwizchip(CW_GET_ID,(void*)tmpstr);
/*
    printf("\r\n=======================================\r\n");
	printf(" WIZnet %s EVB Demos v%d.%.2d\r\n", tmpstr, VER_H, VER_L);
	printf("=======================================\r\n");
	printf(">> W5500 based FTP Client Example\r\n");
	printf("=======================================\r\n");
*/
	Display_Net_Conf(); // Print out the network information to serial terminal
#endif

	/* Enable and setup SysTick Timer at a periodic rate */
	SysTick_Config(SystemCoreClock / TICKRATE_HZ1);

	/* Initialize buttons on the W5500 EVB board */
	Board_Buttons_Init();

	g_sdcard_done = 0;

#if defined(F_APP_FTPC)
	ftpc_init(gWIZNETINFO.ip);
#endif

	ret = flash_mount();
	if(ret > 0)
	{
		display_SDcard_Info(ret);
	}

	while(1) {
	   	/* Button: SW1 */
		if(Check_Buttons_Pressed() == BUTTONS_BUTTON1)
		{
			printf("\r\n########## SW1 was pressed.\r\n");
			printf("########## Data flash flag was cleared.\r\n");
			printf("########## Please reset a target.\r\n");
			release_factory_flag();
		}

#if defined(F_APP_FTPC)
		ftpc_run(gFTPBUF);
#endif

		/* Loopback Test: TCP Server and UDP */
		// Test for Ethernet data transfer validation
		{
			//loopback_tcps(SOCK_TCPS, gDATABUF, PORT_TCPS);
			//loopback_udps(SOCK_UDPS, gDATABUF, PORT_UDPS);
			//loopback_ret = loopback_tcpc(SOCK_TCPS, gDATABUF, destip, destport);

			//if(loopback_ret < 0) printf("loopback ret: %ld\r\n", loopback_ret); // TCP Socket Error code
		}
	}

    return 0 ;
}