/*
* Device state switch handlers.
*/
static int rt2800usb_init_registers(struct rt2x00_dev *rt2x00dev)
{
u32 reg;
/*
* Wait until BBP and RF are ready.
*/
if (rt2800_wait_csr_ready(rt2x00dev))
return -EBUSY;
rt2x00usb_register_read(rt2x00dev, PBF_SYS_CTRL, ®);
rt2x00usb_register_write(rt2x00dev, PBF_SYS_CTRL, reg & ~0x00002000);
rt2x00usb_register_write(rt2x00dev, PWR_PIN_CFG, 0x00000003);
rt2x00usb_register_read(rt2x00dev, MAC_SYS_CTRL, ®);
rt2x00_set_field32(®, MAC_SYS_CTRL_RESET_CSR, 1);
rt2x00_set_field32(®, MAC_SYS_CTRL_RESET_BBP, 1);
rt2x00usb_register_write(rt2x00dev, MAC_SYS_CTRL, reg);
rt2x00usb_register_write(rt2x00dev, USB_DMA_CFG, 0x00000000);
rt2x00usb_vendor_request_sw(rt2x00dev, USB_DEVICE_MODE, 0,
USB_MODE_RESET, REGISTER_TIMEOUT);
rt2x00usb_register_write(rt2x00dev, MAC_SYS_CTRL, 0x00000000);
return 0;
}
static int rt2800usb_write_firmware(struct rt2x00_dev *rt2x00dev,
const u8 *data, const size_t len)
{
int status;
u32 offset;
u32 length;
/*
* Check which section of the firmware we need.
*/
if (rt2x00_rt(rt2x00dev, RT2860) ||
rt2x00_rt(rt2x00dev, RT2872) ||
rt2x00_rt(rt2x00dev, RT3070)) {
offset = 0;
length = 4096;
} else {
offset = 4096;
length = 4096;
}
/*
* Write firmware to device.
*/
rt2800_register_multiwrite(rt2x00dev, FIRMWARE_IMAGE_BASE,
data + offset, length);
rt2800_register_write(rt2x00dev, H2M_MAILBOX_CID, ~0);
rt2800_register_write(rt2x00dev, H2M_MAILBOX_STATUS, ~0);
/*
* Send firmware request to device to load firmware,
* we need to specify a long timeout time.
*/
status = rt2x00usb_vendor_request_sw(rt2x00dev, USB_DEVICE_MODE,
0, USB_MODE_FIRMWARE,
REGISTER_TIMEOUT_FIRMWARE);
if (status < 0) {
ERROR(rt2x00dev, "Failed to write Firmware to device.\n");
return status;
}
msleep(10);
rt2800_register_write(rt2x00dev, H2M_MAILBOX_CSR, 0);
/*
* Send signal to firmware during boot time.
*/
rt2800_mcu_request(rt2x00dev, MCU_BOOT_SIGNAL, 0, 0, 0);
if (rt2x00_rt(rt2x00dev, RT3070) ||
rt2x00_rt(rt2x00dev, RT3071) ||
rt2x00_rt(rt2x00dev, RT3572)) {
udelay(200);
rt2800_mcu_request(rt2x00dev, MCU_CURRENT, 0, 0, 0);
udelay(10);
}
return 0;
}
void rt2x00usb_disable_radio(struct rt2x00_dev *rt2x00dev)
{
rt2x00usb_vendor_request_sw(rt2x00dev, USB_RX_CONTROL, 0, 0,
REGISTER_TIMEOUT);
rt2x00dev->ops->lib->kill_tx_queue(rt2x00dev, QID_RX);
}
/*
* Radio handlers
*/
void rt2x00usb_disable_radio(struct rt2x00_dev *rt2x00dev)
{
rt2x00usb_vendor_request_sw(rt2x00dev, USB_RX_CONTROL, 0, 0,
REGISTER_TIMEOUT);
/*
* The USB version of kill_tx_queue also works
* on the RX queue.
*/
rt2x00dev->ops->lib->kill_tx_queue(rt2x00dev->rx);
}
/*
* Radio handlers
*/
void rt2x00usb_disable_radio(struct rt2x00_dev *rt2x00dev)
{
struct queue_entry_priv_usb_rx *priv_rx;
struct queue_entry_priv_usb_tx *priv_tx;
struct queue_entry_priv_usb_bcn *priv_bcn;
struct data_queue *queue;
unsigned int i;
rt2x00usb_vendor_request_sw(rt2x00dev, USB_RX_CONTROL, 0x0000, 0x0000,
REGISTER_TIMEOUT);
/*
* Cancel all queues.
*/
for (i = 0; i < rt2x00dev->rx->limit; i++) {
priv_rx = rt2x00dev->rx->entries[i].priv_data;
usb_kill_urb(priv_rx->urb);
}
tx_queue_for_each(rt2x00dev, queue) {
for (i = 0; i < queue->limit; i++) {
priv_tx = queue->entries[i].priv_data;
usb_kill_urb(priv_tx->urb);
}
}
for (i = 0; i < rt2x00dev->bcn->limit; i++) {
priv_bcn = rt2x00dev->bcn->entries[i].priv_data;
usb_kill_urb(priv_bcn->urb);
if (priv_bcn->guardian_urb)
usb_kill_urb(priv_bcn->guardian_urb);
}
if (!test_bit(DRIVER_REQUIRE_ATIM_QUEUE, &rt2x00dev->flags))
return;
for (i = 0; i < rt2x00dev->bcn[1].limit; i++) {
priv_tx = rt2x00dev->bcn[1].entries[i].priv_data;
usb_kill_urb(priv_tx->urb);
}
}
static int rt2800usb_init_registers(struct rt2x00_dev *rt2x00dev)
{
u32 reg;
int i;
/*
* Wait until BBP and RF are ready.
*/
for (i = 0; i < REGISTER_BUSY_COUNT; i++) {
rt2800_register_read(rt2x00dev, MAC_CSR0, ®);
if (reg && reg != ~0)
break;
msleep(1);
}
if (i == REGISTER_BUSY_COUNT) {
ERROR(rt2x00dev, "Unstable hardware.\n");
return -EBUSY;
}
rt2800_register_read(rt2x00dev, PBF_SYS_CTRL, ®);
rt2800_register_write(rt2x00dev, PBF_SYS_CTRL, reg & ~0x00002000);
rt2800_register_read(rt2x00dev, MAC_SYS_CTRL, ®);
rt2x00_set_field32(®, MAC_SYS_CTRL_RESET_CSR, 1);
rt2x00_set_field32(®, MAC_SYS_CTRL_RESET_BBP, 1);
rt2800_register_write(rt2x00dev, MAC_SYS_CTRL, reg);
rt2800_register_write(rt2x00dev, USB_DMA_CFG, 0x00000000);
rt2x00usb_vendor_request_sw(rt2x00dev, USB_DEVICE_MODE, 0,
USB_MODE_RESET, REGISTER_TIMEOUT);
rt2800_register_write(rt2x00dev, MAC_SYS_CTRL, 0x00000000);
return 0;
}
/*
* Radio handlers
*/
void rt2x00usb_disable_radio(struct rt2x00_dev *rt2x00dev)
{
rt2x00usb_vendor_request_sw(rt2x00dev, USB_RX_CONTROL, 0, 0,
REGISTER_TIMEOUT);
}
static int rt2800usb_load_firmware(struct rt2x00_dev *rt2x00dev,
const u8 *data, const size_t len)
{
unsigned int i;
int status;
u32 reg;
u32 offset;
u32 length;
/*
* Check which section of the firmware we need.
*/
if (rt2x00_rt(rt2x00dev, RT2860) ||
rt2x00_rt(rt2x00dev, RT2872) ||
rt2x00_rt(rt2x00dev, RT3070)) {
offset = 0;
length = 4096;
} else {
offset = 4096;
length = 4096;
}
/*
* Wait for stable hardware.
*/
for (i = 0; i < REGISTER_BUSY_COUNT; i++) {
rt2800_register_read(rt2x00dev, MAC_CSR0, ®);
if (reg && reg != ~0)
break;
msleep(1);
}
if (i == REGISTER_BUSY_COUNT) {
ERROR(rt2x00dev, "Unstable hardware.\n");
return -EBUSY;
}
/*
* Write firmware to device.
*/
rt2x00usb_vendor_request_large_buff(rt2x00dev, USB_MULTI_WRITE,
USB_VENDOR_REQUEST_OUT,
FIRMWARE_IMAGE_BASE,
data + offset, length,
REGISTER_TIMEOUT32(length));
rt2800_register_write(rt2x00dev, H2M_MAILBOX_CID, ~0);
rt2800_register_write(rt2x00dev, H2M_MAILBOX_STATUS, ~0);
/*
* Send firmware request to device to load firmware,
* we need to specify a long timeout time.
*/
status = rt2x00usb_vendor_request_sw(rt2x00dev, USB_DEVICE_MODE,
0, USB_MODE_FIRMWARE,
REGISTER_TIMEOUT_FIRMWARE);
if (status < 0) {
ERROR(rt2x00dev, "Failed to write Firmware to device.\n");
return status;
}
msleep(10);
rt2800_register_write(rt2x00dev, H2M_MAILBOX_CSR, 0);
/*
* Send signal to firmware during boot time.
*/
rt2800_mcu_request(rt2x00dev, MCU_BOOT_SIGNAL, 0xff, 0, 0);
if (rt2x00_rt(rt2x00dev, RT3070) ||
rt2x00_rt(rt2x00dev, RT3071) ||
rt2x00_rt(rt2x00dev, RT3572)) {
udelay(200);
rt2800_mcu_request(rt2x00dev, MCU_CURRENT, 0, 0, 0);
udelay(10);
}
/*
* Wait for device to stabilize.
*/
for (i = 0; i < REGISTER_BUSY_COUNT; i++) {
rt2800_register_read(rt2x00dev, PBF_SYS_CTRL, ®);
if (rt2x00_get_field32(reg, PBF_SYS_CTRL_READY))
break;
msleep(1);
}
if (i == REGISTER_BUSY_COUNT) {
ERROR(rt2x00dev, "PBF system register not ready.\n");
return -EBUSY;
}
/*
* Initialize firmware.
*/
rt2800_register_write(rt2x00dev, H2M_BBP_AGENT, 0);
rt2800_register_write(rt2x00dev, H2M_MAILBOX_CSR, 0);
msleep(1);
return 0;
}
