void
controls_tick() {
/*
* Gather R/C control inputs from supported sources.
*
* Note that if you're silly enough to connect more than
* one control input source, they're going to fight each
* other. Don't do that.
*/
/* receive signal strenght indicator (RSSI). 0 = no connection, 255: perfect connection */
uint16_t rssi = 0;
#ifdef ADC_RSSI
if (r_setup_features & PX4IO_P_SETUP_FEATURES_ADC_RSSI) {
unsigned counts = adc_measure(ADC_RSSI);
if (counts != 0xffff) {
/* use 1:1 scaling on 3.3V ADC input */
unsigned mV = counts * 3300 / 4096;
/* scale to 0..253 */
rssi = mV / 13;
}
}
#endif
perf_begin(c_gather_dsm);
uint16_t temp_count = r_raw_rc_count;
bool dsm_updated = dsm_input(r_raw_rc_values, &temp_count);
if (dsm_updated) {
r_raw_rc_flags |= PX4IO_P_STATUS_FLAGS_RC_DSM;
r_raw_rc_count = temp_count & 0x7fff;
if (temp_count & 0x8000)
r_raw_rc_flags |= PX4IO_P_RAW_RC_FLAGS_RC_DSM11;
else
r_raw_rc_flags &= ~PX4IO_P_RAW_RC_FLAGS_RC_DSM11;
r_raw_rc_flags &= ~(PX4IO_P_RAW_RC_FLAGS_FRAME_DROP);
r_raw_rc_flags &= ~(PX4IO_P_RAW_RC_FLAGS_FAILSAFE);
}
perf_end(c_gather_dsm);
perf_begin(c_gather_sbus);
bool sbus_status = (r_status_flags & PX4IO_P_STATUS_FLAGS_RC_SBUS);
bool sbus_failsafe, sbus_frame_drop;
bool sbus_updated = sbus_input(r_raw_rc_values, &r_raw_rc_count, &sbus_failsafe, &sbus_frame_drop, PX4IO_RC_INPUT_CHANNELS);
if (sbus_updated) {
r_status_flags |= PX4IO_P_STATUS_FLAGS_RC_SBUS;
rssi = 255;
if (sbus_frame_drop) {
r_raw_rc_flags |= PX4IO_P_RAW_RC_FLAGS_FRAME_DROP;
rssi = 100;
} else {
r_raw_rc_flags &= ~(PX4IO_P_RAW_RC_FLAGS_FRAME_DROP);
}
if (sbus_failsafe) {
r_raw_rc_flags |= PX4IO_P_RAW_RC_FLAGS_FAILSAFE;
rssi = 0;
} else {
r_raw_rc_flags &= ~(PX4IO_P_RAW_RC_FLAGS_FAILSAFE);
}
}
perf_end(c_gather_sbus);
/*
* XXX each S.bus frame will cause a PPM decoder interrupt
* storm (lots of edges). It might be sensible to actually
* disable the PPM decoder completely if we have S.bus signal.
*/
perf_begin(c_gather_ppm);
bool ppm_updated = ppm_input(r_raw_rc_values, &r_raw_rc_count, &r_page_raw_rc_input[PX4IO_P_RAW_RC_DATA]);
if (ppm_updated) {
r_status_flags |= PX4IO_P_STATUS_FLAGS_RC_PPM;
r_raw_rc_flags &= ~(PX4IO_P_RAW_RC_FLAGS_FRAME_DROP);
r_raw_rc_flags &= ~(PX4IO_P_RAW_RC_FLAGS_FAILSAFE);
}
perf_end(c_gather_ppm);
/* limit number of channels to allowable data size */
if (r_raw_rc_count > PX4IO_RC_INPUT_CHANNELS)
r_raw_rc_count = PX4IO_RC_INPUT_CHANNELS;
/* store RSSI */
r_page_raw_rc_input[PX4IO_P_RAW_RC_NRSSI] = rssi;
/*
* In some cases we may have received a frame, but input has still
* been lost.
*/
bool rc_input_lost = false;
/*
* If we received a new frame from any of the RC sources, process it.
*/
if (dsm_updated || sbus_updated || ppm_updated) {
/* record a bitmask of channels assigned */
unsigned assigned_channels = 0;
/* update RC-received timestamp */
system_state.rc_channels_timestamp_received = hrt_absolute_time();
/* do not command anything in failsafe, kick in the RC loss counter */
if (!(r_raw_rc_flags & PX4IO_P_RAW_RC_FLAGS_FAILSAFE)) {
/* update RC-received timestamp */
system_state.rc_channels_timestamp_valid = system_state.rc_channels_timestamp_received;
/* map raw inputs to mapped inputs */
/* XXX mapping should be atomic relative to protocol */
for (unsigned i = 0; i < r_raw_rc_count; i++) {
/* map the input channel */
uint16_t *conf = &r_page_rc_input_config[i * PX4IO_P_RC_CONFIG_STRIDE];
if (conf[PX4IO_P_RC_CONFIG_OPTIONS] & PX4IO_P_RC_CONFIG_OPTIONS_ENABLED) {
uint16_t raw = r_raw_rc_values[i];
int16_t scaled;
/*
* 1) Constrain to min/max values, as later processing depends on bounds.
*/
if (raw < conf[PX4IO_P_RC_CONFIG_MIN])
raw = conf[PX4IO_P_RC_CONFIG_MIN];
if (raw > conf[PX4IO_P_RC_CONFIG_MAX])
raw = conf[PX4IO_P_RC_CONFIG_MAX];
/*
* 2) Scale around the mid point differently for lower and upper range.
*
* This is necessary as they don't share the same endpoints and slope.
*
* First normalize to 0..1 range with correct sign (below or above center),
* then scale to 20000 range (if center is an actual center, -10000..10000,
* if parameters only support half range, scale to 10000 range, e.g. if
* center == min 0..10000, if center == max -10000..0).
*
* As the min and max bounds were enforced in step 1), division by zero
* cannot occur, as for the case of center == min or center == max the if
* statement is mutually exclusive with the arithmetic NaN case.
*
* DO NOT REMOVE OR ALTER STEP 1!
*/
if (raw > (conf[PX4IO_P_RC_CONFIG_CENTER] + conf[PX4IO_P_RC_CONFIG_DEADZONE])) {
scaled = 10000.0f * ((raw - conf[PX4IO_P_RC_CONFIG_CENTER] - conf[PX4IO_P_RC_CONFIG_DEADZONE]) / (float)(conf[PX4IO_P_RC_CONFIG_MAX] - conf[PX4IO_P_RC_CONFIG_CENTER] - conf[PX4IO_P_RC_CONFIG_DEADZONE]));
} else if (raw < (conf[PX4IO_P_RC_CONFIG_CENTER] - conf[PX4IO_P_RC_CONFIG_DEADZONE])) {
scaled = 10000.0f * ((raw - conf[PX4IO_P_RC_CONFIG_CENTER] + conf[PX4IO_P_RC_CONFIG_DEADZONE]) / (float)(conf[PX4IO_P_RC_CONFIG_CENTER] - conf[PX4IO_P_RC_CONFIG_DEADZONE] - conf[PX4IO_P_RC_CONFIG_MIN]));
} else {
/* in the configured dead zone, output zero */
scaled = 0;
}
/* invert channel if requested */
if (conf[PX4IO_P_RC_CONFIG_OPTIONS] & PX4IO_P_RC_CONFIG_OPTIONS_REVERSE)
scaled = -scaled;
/* and update the scaled/mapped version */
unsigned mapped = conf[PX4IO_P_RC_CONFIG_ASSIGNMENT];
if (mapped < PX4IO_CONTROL_CHANNELS) {
/* invert channel if pitch - pulling the lever down means pitching up by convention */
if (mapped == 1) /* roll, pitch, yaw, throttle, override is the standard order */
scaled = -scaled;
r_rc_values[mapped] = SIGNED_TO_REG(scaled);
assigned_channels |= (1 << mapped);
}
}
}
/* set un-assigned controls to zero */
for (unsigned i = 0; i < PX4IO_CONTROL_CHANNELS; i++) {
if (!(assigned_channels & (1 << i)))
r_rc_values[i] = 0;
}
/* set RC OK flag, as we got an update */
r_status_flags |= PX4IO_P_STATUS_FLAGS_RC_OK;
/* if we have enough channels (5) to control the vehicle, the mapping is ok */
if (assigned_channels > 4) {
r_raw_rc_flags |= PX4IO_P_RAW_RC_FLAGS_MAPPING_OK;
} else {
r_raw_rc_flags &= ~(PX4IO_P_RAW_RC_FLAGS_MAPPING_OK);
}
}
/*
* Export the valid channel bitmap
*/
r_rc_valid = assigned_channels;
}
/*
* If we haven't seen any new control data in 200ms, assume we
* have lost input.
*/
if (hrt_elapsed_time(&system_state.rc_channels_timestamp_received) > 200000) {
rc_input_lost = true;
/* clear the input-kind flags here */
r_status_flags &= ~(
PX4IO_P_STATUS_FLAGS_RC_PPM |
PX4IO_P_STATUS_FLAGS_RC_DSM |
PX4IO_P_STATUS_FLAGS_RC_SBUS);
}
/*
* Handle losing RC input
*/
/* this kicks in if the receiver is gone or the system went to failsafe */
if (rc_input_lost || (r_raw_rc_flags & PX4IO_P_RAW_RC_FLAGS_FAILSAFE)) {
/* Clear the RC input status flag, clear manual override flag */
r_status_flags &= ~(
PX4IO_P_STATUS_FLAGS_OVERRIDE |
PX4IO_P_STATUS_FLAGS_RC_OK);
/* Mark all channels as invalid, as we just lost the RX */
r_rc_valid = 0;
/* Set the RC_LOST alarm */
r_status_alarms |= PX4IO_P_STATUS_ALARMS_RC_LOST;
}
/* this kicks in if the receiver is completely gone */
if (rc_input_lost) {
/* Set channel count to zero */
r_raw_rc_count = 0;
}
/*
* Check for manual override.
*
* The PX4IO_P_SETUP_ARMING_MANUAL_OVERRIDE_OK flag must be set, and we
* must have R/C input.
* Override is enabled if either the hardcoded channel / value combination
* is selected, or the AP has requested it.
*/
if ((r_setup_arming & PX4IO_P_SETUP_ARMING_MANUAL_OVERRIDE_OK) &&
(r_status_flags & PX4IO_P_STATUS_FLAGS_RC_OK)) {
bool override = false;
/*
* Check mapped channel 5 (can be any remote channel,
* depends on RC_MAP_OVER parameter);
* If the value is 'high' then the pilot has
* requested override.
*
*/
if ((r_status_flags & PX4IO_P_STATUS_FLAGS_RC_OK) && (REG_TO_SIGNED(r_rc_values[4]) < RC_CHANNEL_LOW_THRESH))
override = true;
if (override) {
r_status_flags |= PX4IO_P_STATUS_FLAGS_OVERRIDE;
/* mix new RC input control values to servos */
if (dsm_updated || sbus_updated || ppm_updated)
mixer_tick();
} else {
void
controls_tick() {
/*
* Gather R/C control inputs from supported sources.
*
* Note that if you're silly enough to connect more than
* one control input source, they're going to fight each
* other. Don't do that.
*/
perf_begin(c_gather_dsm);
bool dsm_updated = dsm_input(r_raw_rc_values, &r_raw_rc_count);
if (dsm_updated)
r_status_flags |= PX4IO_P_STATUS_FLAGS_RC_DSM;
perf_end(c_gather_dsm);
perf_begin(c_gather_sbus);
bool sbus_updated = sbus_input(r_raw_rc_values, &r_raw_rc_count);
if (sbus_updated)
r_status_flags |= PX4IO_P_STATUS_FLAGS_RC_SBUS;
perf_end(c_gather_sbus);
/*
* XXX each S.bus frame will cause a PPM decoder interrupt
* storm (lots of edges). It might be sensible to actually
* disable the PPM decoder completely if we have S.bus signal.
*/
perf_begin(c_gather_ppm);
bool ppm_updated = ppm_input(r_raw_rc_values, &r_raw_rc_count);
if (ppm_updated)
r_status_flags |= PX4IO_P_STATUS_FLAGS_RC_PPM;
perf_end(c_gather_ppm);
ASSERT(r_raw_rc_count <= MAX_CONTROL_CHANNELS);
/*
* In some cases we may have received a frame, but input has still
* been lost.
*/
bool rc_input_lost = false;
/*
* If we received a new frame from any of the RC sources, process it.
*/
if (dsm_updated || sbus_updated || ppm_updated) {
/* update RC-received timestamp */
system_state.rc_channels_timestamp = hrt_absolute_time();
/* record a bitmask of channels assigned */
unsigned assigned_channels = 0;
/* map raw inputs to mapped inputs */
/* XXX mapping should be atomic relative to protocol */
for (unsigned i = 0; i < r_raw_rc_count; i++) {
/* map the input channel */
uint16_t *conf = &r_page_rc_input_config[i * PX4IO_P_RC_CONFIG_STRIDE];
if (conf[PX4IO_P_RC_CONFIG_OPTIONS] & PX4IO_P_RC_CONFIG_OPTIONS_ENABLED) {
uint16_t raw = r_raw_rc_values[i];
int16_t scaled;
/*
* 1) Constrain to min/max values, as later processing depends on bounds.
*/
if (raw < conf[PX4IO_P_RC_CONFIG_MIN])
raw = conf[PX4IO_P_RC_CONFIG_MIN];
if (raw > conf[PX4IO_P_RC_CONFIG_MAX])
raw = conf[PX4IO_P_RC_CONFIG_MAX];
/*
* 2) Scale around the mid point differently for lower and upper range.
*
* This is necessary as they don't share the same endpoints and slope.
*
* First normalize to 0..1 range with correct sign (below or above center),
* then scale to 20000 range (if center is an actual center, -10000..10000,
* if parameters only support half range, scale to 10000 range, e.g. if
* center == min 0..10000, if center == max -10000..0).
*
* As the min and max bounds were enforced in step 1), division by zero
* cannot occur, as for the case of center == min or center == max the if
* statement is mutually exclusive with the arithmetic NaN case.
*
* DO NOT REMOVE OR ALTER STEP 1!
*/
if (raw > (conf[PX4IO_P_RC_CONFIG_CENTER] + conf[PX4IO_P_RC_CONFIG_DEADZONE])) {
scaled = 10000.0f * ((raw - conf[PX4IO_P_RC_CONFIG_CENTER] - conf[PX4IO_P_RC_CONFIG_DEADZONE]) / (float)(conf[PX4IO_P_RC_CONFIG_MAX] - conf[PX4IO_P_RC_CONFIG_CENTER] - conf[PX4IO_P_RC_CONFIG_DEADZONE]));
} else if (raw < (conf[PX4IO_P_RC_CONFIG_CENTER] - conf[PX4IO_P_RC_CONFIG_DEADZONE])) {
scaled = 10000.0f * ((raw - conf[PX4IO_P_RC_CONFIG_CENTER] - conf[PX4IO_P_RC_CONFIG_DEADZONE]) / (float)(conf[PX4IO_P_RC_CONFIG_CENTER] - conf[PX4IO_P_RC_CONFIG_DEADZONE] - conf[PX4IO_P_RC_CONFIG_MIN]));
} else {
/* in the configured dead zone, output zero */
scaled = 0;
}
/* invert channel if requested */
if (conf[PX4IO_P_RC_CONFIG_OPTIONS] & PX4IO_P_RC_CONFIG_OPTIONS_REVERSE)
scaled = -scaled;
/* and update the scaled/mapped version */
unsigned mapped = conf[PX4IO_P_RC_CONFIG_ASSIGNMENT];
ASSERT(mapped < MAX_CONTROL_CHANNELS);
/* invert channel if pitch - pulling the lever down means pitching up by convention */
if (mapped == 1) /* roll, pitch, yaw, throttle, override is the standard order */
scaled = -scaled;
r_rc_values[mapped] = SIGNED_TO_REG(scaled);
assigned_channels |= (1 << mapped);
}
}
/* set un-assigned controls to zero */
for (unsigned i = 0; i < MAX_CONTROL_CHANNELS; i++) {
if (!(assigned_channels & (1 << i)))
r_rc_values[i] = 0;
}
/*
* If we got an update with zero channels, treat it as
* a loss of input.
*
* This might happen if a protocol-based receiver returns an update
* that contains no channels that we have mapped.
*/
if (assigned_channels == 0) {
rc_input_lost = true;
} else {
/* set RC OK flag and clear RC lost alarm */
r_status_flags |= PX4IO_P_STATUS_FLAGS_RC_OK;
r_status_alarms &= ~PX4IO_P_STATUS_ALARMS_RC_LOST;
}
/*
* Export the valid channel bitmap
*/
r_rc_valid = assigned_channels;
}
/*
* If we haven't seen any new control data in 200ms, assume we
* have lost input.
*/
if (hrt_elapsed_time(&system_state.rc_channels_timestamp) > 200000) {
rc_input_lost = true;
/* clear the input-kind flags here */
r_status_flags &= ~(
PX4IO_P_STATUS_FLAGS_RC_PPM |
PX4IO_P_STATUS_FLAGS_RC_DSM |
PX4IO_P_STATUS_FLAGS_RC_SBUS);
}
/*
* Handle losing RC input
*/
if (rc_input_lost) {
/* Clear the RC input status flag, clear manual override flag */
r_status_flags &= ~(
PX4IO_P_STATUS_FLAGS_OVERRIDE |
PX4IO_P_STATUS_FLAGS_RC_OK);
/* Set the RC_LOST alarm */
r_status_alarms |= PX4IO_P_STATUS_ALARMS_RC_LOST;
/* Mark the arrays as empty */
r_raw_rc_count = 0;
r_rc_valid = 0;
}
/*
* Check for manual override.
*
* The PX4IO_P_SETUP_ARMING_MANUAL_OVERRIDE_OK flag must be set, and we
* must have R/C input.
* Override is enabled if either the hardcoded channel / value combination
* is selected, or the AP has requested it.
*/
if ((r_setup_arming & PX4IO_P_SETUP_ARMING_MANUAL_OVERRIDE_OK) &&
(r_status_flags & PX4IO_P_STATUS_FLAGS_RC_OK)) {
bool override = false;
/*
* Check mapped channel 5 (can be any remote channel,
* depends on RC_MAP_OVER parameter);
* If the value is 'high' then the pilot has
* requested override.
*
*/
if ((r_status_flags & PX4IO_P_STATUS_FLAGS_RC_OK) && (REG_TO_SIGNED(r_rc_values[4]) > RC_CHANNEL_HIGH_THRESH))
override = true;
if (override) {
r_status_flags |= PX4IO_P_STATUS_FLAGS_OVERRIDE;
/* mix new RC input control values to servos */
if (dsm_updated || sbus_updated || ppm_updated)
mixer_tick();
} else {
void
controls_main(void)
{
struct pollfd fds[2];
/* DSM input */
fds[0].fd = dsm_init("/dev/ttyS0");
fds[0].events = POLLIN;
/* S.bus input */
fds[1].fd = sbus_init("/dev/ttyS2");
fds[1].events = POLLIN;
for (;;) {
/* run this loop at ~100Hz */
poll(fds, 2, 10);
/*
* Gather R/C control inputs from supported sources.
*
* Note that if you're silly enough to connect more than
* one control input source, they're going to fight each
* other. Don't do that.
*/
bool locked = false;
if (fds[0].revents & POLLIN)
locked |= dsm_input();
if (fds[1].revents & POLLIN)
locked |= sbus_input();
/*
* If we don't have lock from one of the serial receivers,
* look for PPM. It shares an input with S.bus, so there's
* a possibility it will mis-parse an S.bus frame.
*
* XXX each S.bus frame will cause a PPM decoder interrupt
* storm (lots of edges). It might be sensible to actually
* disable the PPM decoder completely if we have an alternate
* receiver lock.
*/
if (!locked)
ppm_input();
/*
* If we haven't seen any new control data in 200ms, assume we
* have lost input and tell FMU.
*/
if ((hrt_absolute_time() - system_state.rc_channels_timestamp) > 200000) {
/* set the number of channels to zero - no inputs */
system_state.rc_channels = 0;
/* trigger an immediate report to the FMU */
system_state.fmu_report_due = true;
}
/* XXX do bypass mode, etc. here */
/* do PWM output updates */
mixer_tick();
}
}
void
PX4FMU::cycle()
{
if (!_initialized) {
/* force a reset of the update rate */
_current_update_rate = 0;
_armed_sub = orb_subscribe(ORB_ID(actuator_armed));
//_param_sub = orb_subscribe(ORB_ID(parameter_update));
/* initialize PWM limit lib */
pwm_limit_init(&_pwm_limit);
update_pwm_rev_mask();
#ifdef RC_SERIAL_PORT
_sbus_fd = sbus_init(RC_SERIAL_PORT, true);
#endif
_initialized = true;
}
if (_groups_subscribed != _groups_required) {
subscribe();
_groups_subscribed = _groups_required;
/* force setting update rate */
_current_update_rate = 0;
}
/*
* Adjust actuator topic update rate to keep up with
* the highest servo update rate configured.
*
* We always mix at max rate; some channels may update slower.
*/
unsigned max_rate = (_pwm_default_rate > _pwm_alt_rate) ? _pwm_default_rate : _pwm_alt_rate;
if (_current_update_rate != max_rate) {
_current_update_rate = max_rate;
int update_rate_in_ms = int(1000 / _current_update_rate);
/* reject faster than 500 Hz updates */
if (update_rate_in_ms < 2) {
update_rate_in_ms = 2;
}
/* reject slower than 10 Hz updates */
if (update_rate_in_ms > 100) {
update_rate_in_ms = 100;
}
//DEVICE_DEBUG("adjusted actuator update interval to %ums\n", update_rate_in_ms);
for (unsigned i = 0; i < actuator_controls_s::NUM_ACTUATOR_CONTROL_GROUPS; i++) {
if (_control_subs[i] > 0) {
orb_set_interval(_control_subs[i], update_rate_in_ms);
}
}
// set to current max rate, even if we are actually checking slower/faster
_current_update_rate = max_rate;
}
/* check if anything updated */
//从mkblctrl-blctrl电子模块驱动拿数据，貌似没用到，而且poll里面也在等待定时器导致定时器卡死
int ret = 0;//::poll(_poll_fds, _poll_fds_num, 0);
/* this would be bad... */
if (ret < 0) {
DEVICE_LOG("poll error %d\n", ret);
} else if (ret == 0) {
/* timeout: no control data, switch to failsafe values */
// warnx("no PWM: failsafe\n");
} else {
/* get controls for required topics */
unsigned poll_id = 0;
for (unsigned i = 0; i < actuator_controls_s::NUM_ACTUATOR_CONTROL_GROUPS; i++) {
if (_control_subs[i] > 0) {
if (_poll_fds[poll_id].revents & POLLIN) {
orb_copy(_control_topics[i], _control_subs[i], &_controls[i]);
}
poll_id++;
}
}
/* can we mix? */
if (_mixers != NULL) {
size_t num_outputs;
switch (_mode) {
case MODE_2PWM:
num_outputs = 2;
break;
case MODE_4PWM:
num_outputs = 4;
break;
case MODE_6PWM:
num_outputs = 6;
break;
case MODE_8PWM:
num_outputs = 8;
break;
default:
num_outputs = 0;
break;
}
/* do mixing */
float outputs[_max_actuators];
num_outputs = _mixers->mix(outputs, num_outputs, NULL);
/* disable unused ports by setting their output to NaN */
for (size_t i = 0; i < sizeof(outputs) / sizeof(outputs[0]); i++) {
if (i >= num_outputs) {
outputs[i] = NAN_VALUE;
}
}
uint16_t pwm_limited[_max_actuators];
/* the PWM limit call takes care of out of band errors, NaN and constrains */
pwm_limit_calc(_servo_armed, arm_nothrottle(), num_outputs, _reverse_pwm_mask, _disarmed_pwm, _min_pwm, _max_pwm,
outputs, pwm_limited, &_pwm_limit);
/* output to the servos */
for (size_t i = 0; i < num_outputs; i++) {
up_pwm_servo_set(i, pwm_limited[i]);
}
publish_pwm_outputs(pwm_limited, num_outputs);
}
}
/* check arming state */
bool updated = false;
orb_check(_armed_sub, &updated);
if (updated) {
orb_copy(ORB_ID(actuator_armed), _armed_sub, &_armed);
/* update the armed status and check that we're not locked down */
bool set_armed = (_armed.armed || _armed.prearmed) && !_armed.lockdown;
if (_servo_armed != set_armed) {
_servo_armed = set_armed;
}
/* update PWM status if armed or if disarmed PWM values are set */
bool pwm_on = (set_armed || _num_disarmed_set > 0);
if (_pwm_on != pwm_on) {
_pwm_on = pwm_on;
up_pwm_servo_arm(pwm_on);
}
}
/* TODO:F
orb_check(_param_sub, &updated);
if (updated) {
parameter_update_s pupdate;
orb_copy(ORB_ID(parameter_update), _param_sub, &pupdate);
update_pwm_rev_mask();
}
*/
bool rc_updated = false;
#ifdef RC_SERIAL_PORT
bool sbus_failsafe, sbus_frame_drop;
uint16_t raw_rc_values[input_rc_s::RC_INPUT_MAX_CHANNELS];
uint16_t raw_rc_count;
bool sbus_updated = sbus_input(_sbus_fd, &raw_rc_values[0], &raw_rc_count, &sbus_failsafe, &sbus_frame_drop,
input_rc_s::RC_INPUT_MAX_CHANNELS);
if (sbus_updated) {
// we have a new PPM frame. Publish it.
_rc_in.channel_count = raw_rc_count;
if (_rc_in.channel_count > input_rc_s::RC_INPUT_MAX_CHANNELS) {
_rc_in.channel_count = input_rc_s::RC_INPUT_MAX_CHANNELS;
}
for (uint8_t i = 0; i < _rc_in.channel_count; i++) {
_rc_in.values[i] = raw_rc_values[i];
// pilot_info("value[%d]=%d\n", i, _rc_in.values[i]);
}
_rc_in.timestamp_publication = hrt_absolute_time();
_rc_in.timestamp_last_signal = _rc_in.timestamp_publication;
_rc_in.rc_ppm_frame_length = 0;
_rc_in.rssi = (!sbus_frame_drop) ? RC_INPUT_RSSI_MAX : 0;
_rc_in.rc_failsafe = false;
_rc_in.rc_lost = false;
_rc_in.rc_lost_frame_count = 0;
_rc_in.rc_total_frame_count = 0;
rc_updated = true;
}
#endif
#ifdef HRT_PPM_CHANNEL
// see if we have new PPM input data
if ((ppm_last_valid_decode != _rc_in.timestamp_last_signal) &&
ppm_decoded_channels > 3) {
// we have a new PPM frame. Publish it.
_rc_in.channel_count = ppm_decoded_channels;
if (_rc_in.channel_count > input_rc_s::RC_INPUT_MAX_CHANNELS) {
_rc_in.channel_count = input_rc_s::RC_INPUT_MAX_CHANNELS;
}
for (uint8_t i = 0; i < _rc_in.channel_count; i++) {
_rc_in.values[i] = ppm_buffer[i];
}
_rc_in.timestamp_publication = ppm_last_valid_decode;
_rc_in.timestamp_last_signal = ppm_last_valid_decode;
_rc_in.rc_ppm_frame_length = ppm_frame_length;
_rc_in.rssi = RC_INPUT_RSSI_MAX;
_rc_in.rc_failsafe = false;
_rc_in.rc_lost = false;
_rc_in.rc_lost_frame_count = 0;
_rc_in.rc_total_frame_count = 0;
rc_updated = true;
}
#endif
if (rc_updated) {
/* lazily advertise on first publication */
if (_to_input_rc == NULL) {
_to_input_rc = orb_advertise(ORB_ID(input_rc), &_rc_in);
} else {
orb_publish(ORB_ID(input_rc), _to_input_rc, &_rc_in);
}
}
// xTimerStart(_work, (2/portTICK_PERIOD_MS));
}
void
comms_check(void)
{
/*
* Check for serial data
*/
int ret = poll(pollfds, pollcount, 0);
if (ret > 0) {
/*
* Pull bytes from FMU and feed them to the HX engine.
* Limit the number of bytes we actually process on any one iteration.
*/
if (pollfds[0].revents & POLLIN) {
char buf[32];
ssize_t count = read(fmu_fd, buf, sizeof(buf));
for (int i = 0; i < count; i++)
hx_stream_rx(stream, buf[i]);
}
/*
* Pull bytes from the serial RX port and feed them to the decoder
* if we care about serial RX data.
*/
if ((pollcount > 1) && (pollfds[1].revents & POLLIN)) {
switch (system_state.serial_rx_mode) {
case RX_MODE_DSM_10BIT:
case RX_MODE_DSM_11BIT:
dsm_input(rx_fd);
break;
case RX_MODE_FUTABA_SBUS:
sbus_input(rx_fd);
break;
default:
break;
}
}
}
/*
* Decide if it's time to send an update to the FMU.
*/
static hrt_abstime last_report_time;
hrt_abstime now, delta;
/* should we send a report to the FMU? */
now = hrt_absolute_time();
delta = now - last_report_time;
if ((delta > FMU_MIN_REPORT_INTERVAL) &&
(system_state.fmu_report_due || (delta > FMU_MAX_REPORT_INTERVAL))) {
system_state.fmu_report_due = false;
last_report_time = now;
/* populate the report */
for (int i = 0; i < system_state.rc_channels; i++)
report.rc_channel[i] = system_state.rc_channel_data[i];
report.channel_count = system_state.rc_channels;
report.armed = system_state.armed;
/* and send it */
hx_stream_send(stream, &report, sizeof(report));
}
}
