static int
sd_get_parms(struct sd_softc *sd)
{
struct disk_parms *dp = &sd->sc_params;
int error;
/*
* If offline, the SDEV_MEDIA_LOADED flag will be
* cleared by the caller if necessary.
*/
if (sd->sc_type == T_SIMPLE_DIRECT) {
error = sd_get_simplifiedparms(sd);
if (error)
return error;
goto ok;
}
error = sd_get_capacity(sd);
if (error)
return error;
if (sd->sc_type == T_OPTICAL)
goto page0;
if (sd->sc_flags & FLAGS_REMOVABLE) {
if (!sd_get_parms_page5(sd, dp) ||
!sd_get_parms_page4(sd, dp))
goto ok;
} else {
if (!sd_get_parms_page4(sd, dp) ||
!sd_get_parms_page5(sd, dp))
goto ok;
}
page0:
printf("fabricating a geometry\n");
/* Try calling driver's method for figuring out geometry. */
/*
* Use adaptec standard fictitious geometry
* this depends on which controller (e.g. 1542C is
* different. but we have to put SOMETHING here..)
*/
dp->heads = 64;
dp->sectors = 32;
dp->cyls = dp->disksize / (64 * 32);
dp->rot_rate = 3600;
ok:
DPRINTF(("disksize = %" PRId64 ", disksize512 = %" PRId64 ".\n",
dp->disksize, dp->disksize512));
return 0;
}
int
main(void)
{
#if WITH_SD
int r;
#endif /* WITH_SD */
msp430_cpu_init();
watchdog_stop();
/* Platform-specific initialization. */
msb_ports_init();
adc_init();
clock_init();
rtimer_init();
sht11_init();
leds_init();
leds_on(LEDS_ALL);
irq_init();
process_init();
/* serial interface */
rs232_set_input(serial_line_input_byte);
rs232_init();
serial_line_init();
uart_lock(UART_MODE_RS232);
uart_unlock(UART_MODE_RS232);
#if WITH_UIP
slip_arch_init(BAUD2UBR(115200));
#endif
#if WITH_SD
r = sd_initialize();
if(r < 0) {
printf("Failed to initialize the SD driver: %s\n", sd_error_string(r));
} else {
sd_offset_t capacity;
printf("The SD driver was successfully initialized\n");
capacity = sd_get_capacity();
if(capacity < 0) {
printf("Failed to get the SD card capacity: %s\n", sd_error_string(r));
} else {
printf("SD card capacity: %u MB\n",
(unsigned)(capacity / (1024UL * 1024)));
}
}
#endif
/* System services */
process_start(&etimer_process, NULL);
ctimer_init();
node_id_restore();
init_net();
energest_init();
#if PROFILE_CONF_ON
profile_init();
#endif /* PROFILE_CONF_ON */
leds_off(LEDS_ALL);
printf(CONTIKI_VERSION_STRING " started. Node id %u, using %s.\n",
node_id, rime_mac->name);
autostart_start(autostart_processes);
/*
* This is the scheduler loop.
*/
ENERGEST_ON(ENERGEST_TYPE_CPU);
while (1) {
int r;
#if PROFILE_CONF_ON
profile_episode_start();
#endif /* PROFILE_CONF_ON */
do {
/* Reset watchdog. */
watchdog_periodic();
r = process_run();
} while(r > 0);
#if PROFILE_CONF_ON
profile_episode_end();
#endif /* PROFILE_CONF_ON */
/*
* Idle processing.
*/
int s = splhigh(); /* Disable interrupts. */
if (process_nevents() != 0) {
splx(s); /* Re-enable interrupts. */
} else {
static unsigned long irq_energest = 0;
/* Re-enable interrupts and go to sleep atomically. */
ENERGEST_OFF(ENERGEST_TYPE_CPU);
ENERGEST_ON(ENERGEST_TYPE_LPM);
/*
* We only want to measure the processing done in IRQs when we
* are asleep, so we discard the processing time done when we
* were awake.
*/
energest_type_set(ENERGEST_TYPE_IRQ, irq_energest);
if (uart_edge) {
_BIC_SR(LPM1_bits + GIE);
} else {
_BIS_SR(LPM1_bits + GIE);
}
/*
* We get the current processing time for interrupts that was
* done during the LPM and store it for next time around.
*/
dint();
irq_energest = energest_type_time(ENERGEST_TYPE_IRQ);
eint();
ENERGEST_OFF(ENERGEST_TYPE_LPM);
ENERGEST_ON(ENERGEST_TYPE_CPU);
#if PROFILE_CONF_ON
profile_clear_timestamps();
#endif /* PROFILE_CONF_ON */
}
}
return 0;
}
