void __init bit2440_init(void)
{
set_s3c2410ts_info(&bit2440_ts_cfg);
set_s3c2410udc_info(&bit2440_udc_cfg);
set_s3c2410fb_info(&bit2440_lcdcfg);
s3c2410_gpio_cfgpin(S3C2410_GPH0, S3C2410_GPH0_OUTP);
s3c2410_gpio_pullup(S3C2410_GPH0, 0);
s3c2410_gpio_setpin(S3C2410_GPH0, 0);
/* set LED start status by lili */
s3c2410_gpio_cfgpin(S3C2410_GPF4, S3C2410_GPF4_OUTP);
s3c2410_gpio_cfgpin(S3C2410_GPF5, S3C2410_GPF5_OUTP);
s3c2410_gpio_cfgpin(S3C2410_GPF6, S3C2410_GPF6_OUTP);
s3c2410_gpio_cfgpin(S3C2410_GPF7, S3C2410_GPF7_OUTP);
s3c2410_gpio_setpin(S3C2410_GPF4, 0);
s3c2410_gpio_setpin(S3C2410_GPF5, 0);
s3c2410_gpio_setpin(S3C2410_GPF6, 0);
s3c2410_gpio_setpin(S3C2410_GPF7, 0);
/* Add by lili for usb setup*/
printk("USB Power Control, (c) 2004 Simtec Electronics\n");
s3c_device_usb.dev.platform_data = &usb_simtec_info;
s3c2410_gpio_cfgpin(S3C2410_GPB4, S3C2410_GPB4_OUTP);
s3c2410_gpio_setpin(S3C2410_GPB4, 1);
}
void __init smdk_machine_init(void)
{
/* Configure the LEDs (even if we have no LED support)*/
s3c2410_gpio_cfgpin(S3C2410_GPF4, S3C2410_GPF4_OUTP);
s3c2410_gpio_cfgpin(S3C2410_GPF5, S3C2410_GPF5_OUTP);
s3c2410_gpio_cfgpin(S3C2410_GPF6, S3C2410_GPF6_OUTP);
s3c2410_gpio_cfgpin(S3C2410_GPF7, S3C2410_GPF7_OUTP);
s3c2410_gpio_setpin(S3C2410_GPF4, 1);
s3c2410_gpio_setpin(S3C2410_GPF5, 1);
s3c2410_gpio_setpin(S3C2410_GPF6, 1);
s3c2410_gpio_setpin(S3C2410_GPF7, 1);
if (machine_is_smdk2443())
smdk_nand_info.twrph0 = 50;
s3c_device_nand.dev.platform_data = &smdk_nand_info;
#ifdef CONFIG_TOUCHSCREEN_S3C2410
set_s3c2410ts_info(&s3c2410_ts_cfg);
#endif
platform_add_devices(smdk_devs, ARRAY_SIZE(smdk_devs));
s3c2410_pm_init();
}
static void __init smdk2440_map_io(void)
{
s3c24xx_init_io(smdk2440_iodesc, ARRAY_SIZE(smdk2440_iodesc));
s3c24xx_init_clocks(16934400);
s3c24xx_init_uarts(smdk2440_uartcfgs, ARRAY_SIZE(smdk2440_uartcfgs));
set_s3c2410ts_info(&elayer_s24xx_ts_cfg);
}
static void __init falinuxs3c2440_map_io(void)
{
s3c24xx_init_io(falinuxs3c2440_iodesc, ARRAY_SIZE(falinuxs3c2440_iodesc));
s3c24xx_init_clocks(16934400);
s3c24xx_init_uarts(falinuxs3c2440_uartcfgs, ARRAY_SIZE(falinuxs3c2440_uartcfgs));
s3c24xx_set_board(&falinuxs3c2440_board);
set_s3c2410ts_info(&falinux_s24xx_ts_cfg);
}
static void __init gta02_machine_init(void)
{
int rc;
/* set the panic callback to make AUX blink fast */
panic_blink = gta02_panic_blink;
switch (S3C_SYSTEM_REV_ATAG) {
case GTA02v6_SYSTEM_REV:
/* we need push-pull interrupt from motion sensors */
lis302_pdata_top.open_drain = 0;
lis302_pdata_bottom.open_drain = 0;
break;
default:
break;
}
spin_lock_init(&motion_irq_lock);
#ifdef CONFIG_CHARGER_PCF50633
INIT_DELAYED_WORK(>a02_charger_work, gta02_charger_worker);
#endif
/* Glamo chip select optimization */
/* *((u32 *)(S3C2410_MEMREG(((1 + 1) << 2)))) = 0x1280; */
/* do not force soft ecc if we are asked to use hardware_ecc */
if (hardware_ecc_str[0] == '1')
gta02_nand_info.software_ecc = 0;
s3c_device_usb.dev.platform_data = >a02_usb_info;
s3c_device_nand.dev.platform_data = >a02_nand_info;
s3c_device_sdi.dev.platform_data = >a02_s3c_mmc_cfg;
/* acc sensor chip selects */
s3c2410_gpio_setpin(S3C2410_GPD12, 1);
s3c2410_gpio_cfgpin(S3C2410_GPD12, S3C2410_GPIO_OUTPUT);
s3c2410_gpio_setpin(S3C2410_GPD13, 1);
s3c2410_gpio_cfgpin(S3C2410_GPD13, S3C2410_GPIO_OUTPUT);
s3c24xx_udc_set_platdata(>a02_udc_cfg);
s3c_i2c0_set_platdata(NULL);
set_s3c2410ts_info(>a02_ts_cfg);
mangle_glamo_res_by_system_rev();
i2c_register_board_info(0, gta02_i2c_devs, ARRAY_SIZE(gta02_i2c_devs));
spi_register_board_info(gta02_spi_board_info,
ARRAY_SIZE(gta02_spi_board_info));
#ifdef CONFIG_CHARGER_PCF50633
mangle_pmu_pdata_by_system_rev();
#endif
platform_add_devices(gta02_devices, ARRAY_SIZE(gta02_devices));
s3c_pm_init();
/* Make sure the modem can wake us up */
set_irq_type(GTA02_IRQ_MODEM, IRQ_TYPE_EDGE_RISING);
rc = request_irq(GTA02_IRQ_MODEM, gta02_modem_irq, IRQF_DISABLED,
"modem", NULL);
if (rc < 0)
printk(KERN_ERR "GTA02: can't request GSM modem wakeup IRQ\n");
enable_irq_wake(GTA02_IRQ_MODEM);
/* Make sure the wifi module can wake us up*/
set_irq_type(GTA02_IRQ_WLAN_GPIO1, IRQ_TYPE_EDGE_RISING);
rc = request_irq(GTA02_IRQ_WLAN_GPIO1, ar6000_wow_irq, IRQF_DISABLED,
"ar6000", NULL);
if (rc < 0)
printk(KERN_ERR "GTA02: can't request ar6k wakeup IRQ\n");
enable_irq_wake(GTA02_IRQ_WLAN_GPIO1);
pm_power_off = gta02_poweroff;
/* Register the HDQ and vibrator as children of pwm device */
#ifdef CONFIG_HDQ_GPIO_BITBANG
gta02_hdq_device.dev.parent = &s3c24xx_pwm_device.dev;
platform_device_register(>a02_hdq_device);
#endif
#ifdef CONFIG_LEDS_GTA02_VIBRATOR
gta02_vibrator_dev.dev.parent = &s3c24xx_pwm_device.dev;
platform_device_register(>a02_vibrator_dev);
#endif
}
