int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
imx_iomux_v3_setup_multiple_pads(iox_pads, ARRAY_SIZE(iox_pads));
iox74lv_init();
#ifdef CONFIG_FEC_MXC
setup_fec();
#endif
#ifdef CONFIG_SYS_USE_NAND
setup_gpmi_nand();
#endif
#ifdef CONFIG_FSL_QSPI
board_qspi_init();
#endif
#ifdef CONFIG_MXC_EPDC
qn_output[5] = qn_disable;
iox74lv_set(5);
setup_epdc();
#endif
return 0;
}
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
#if defined(CONFIG_MX6DL) && defined(CONFIG_MXC_EPDC)
setup_epdc();
#endif
return 0;
}
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
#ifdef CONFIG_FEC_MXC
setup_fec();
#endif
#ifdef CONFIG_MXC_EPDC
setup_epdc();
#endif
return 0;
}
int board_init(void)
{
/*
* need set Power Supply Glitch to 0x41736166
* and need clear Power supply Glitch Detect bit
* when POR or reboot or power on Otherwise system
* could not be power off anymore;
* need to set SNVS work at DUMP mode;
* */
u32 reg;
writel(0x41736166, SNVS_BASE_ADDR + 0x64);/*set LPPGDR*/
udelay(10);
reg = readl(SNVS_BASE_ADDR + 0x4c);
reg |= (1 << 3);
writel(reg, SNVS_BASE_ADDR + 0x4c);/*clear LPSR*/
mxc_iomux_v3_init((void *)IOMUXC_BASE_ADDR);
setup_boot_device();
fsl_set_system_rev();
/* board id for linux */
gd->bd->bi_arch_number = MACH_TYPE_MX6SL_EVK;
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
wdog_preconfig(WDOG1_BASE_ADDR);
setup_uart();
#ifdef CONFIG_MXC_FEC
setup_fec();
#endif
#ifdef CONFIG_MXC_EPDC
setup_epdc();
#endif
return 0;
}
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
#ifdef CONFIG_MXC_SPI
setup_spi();
#endif
setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
#ifdef CONFIG_USB_EHCI_MX6
setup_usb();
#endif
#if defined(CONFIG_MX6DL) && defined(CONFIG_MXC_EPDC)
setup_epdc();
#endif
#ifdef CONFIG_CMD_SATA
setup_sata();
#endif
return 0;
}
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
#ifdef CONFIG_SYS_I2C_MXC
setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
setup_elan_pads();
#endif
#ifdef CONFIG_FEC_MXC
setup_fec();
#endif
#ifdef CONFIG_MXC_EPDC
setup_epdc();
#endif
#ifdef CONFIG_USB_EHCI_MX6
setup_usb();
#endif
return 0;
}
