static void sirfsoc_uart_shutdown(struct uart_port *port)
{
struct sirfsoc_uart_port *sirfport = to_sirfport(port);
struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg;
struct circ_buf *xmit;
xmit = &sirfport->rx_dma_items.xmit;
if (!sirfport->is_atlas7)
wr_regl(port, ureg->sirfsoc_int_en_reg, 0);
else
wr_regl(port, ureg->sirfsoc_int_en_clr_reg, ~0UL);
free_irq(port->irq, sirfport);
if (sirfport->ms_enabled)
sirfsoc_uart_disable_ms(port);
if (sirfport->uart_reg->uart_type == SIRF_USP_UART &&
sirfport->hw_flow_ctrl) {
gpio_set_value(sirfport->rts_gpio, 1);
free_irq(gpio_to_irq(sirfport->cts_gpio), sirfport);
}
if (sirfport->tx_dma_chan)
sirfport->tx_dma_state = TX_DMA_IDLE;
if (sirfport->rx_dma_chan && sirfport->is_hrt_enabled) {
while (((rd_regl(port, ureg->sirfsoc_rx_fifo_status) &
SIRFUART_RX_FIFO_MASK) > sirfport->pio_fetch_cnt) &&
!CIRC_CNT(xmit->head, xmit->tail,
SIRFSOC_RX_DMA_BUF_SIZE))
;
sirfport->is_hrt_enabled = false;
hrtimer_cancel(&sirfport->hrt);
}
}
static void sirfsoc_uart_shutdown(struct uart_port *port)
{
struct sirfsoc_uart_port *sirfport = to_sirfport(port);
wr_regl(port, SIRFUART_INT_EN, 0);
free_irq(port->irq, sirfport);
if (sirfport->ms_enabled) {
sirfsoc_uart_disable_ms(port);
sirfport->ms_enabled = 0;
}
}
static void sirfsoc_uart_shutdown(struct uart_port *port)
{
struct sirfsoc_uart_port *sirfport = to_sirfport(port);
struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg;
if (!sirfport->is_atlas7)
wr_regl(port, ureg->sirfsoc_int_en_reg, 0);
else
wr_regl(port, SIRFUART_INT_EN_CLR, ~0UL);
free_irq(port->irq, sirfport);
if (sirfport->ms_enabled)
sirfsoc_uart_disable_ms(port);
if (sirfport->uart_reg->uart_type == SIRF_USP_UART &&
sirfport->hw_flow_ctrl) {
gpio_set_value(sirfport->rts_gpio, 1);
free_irq(gpio_to_irq(sirfport->cts_gpio), sirfport);
}
if (sirfport->tx_dma_chan)
sirfport->tx_dma_state = TX_DMA_IDLE;
}
static void sirfsoc_uart_set_termios(struct uart_port *port,
struct ktermios *termios,
struct ktermios *old)
{
struct sirfsoc_uart_port *sirfport = to_sirfport(port);
unsigned long config_reg = 0;
unsigned long baud_rate;
unsigned long setted_baud;
unsigned long flags;
unsigned long ic;
unsigned int clk_div_reg = 0;
unsigned long temp_reg_val;
unsigned long rx_time_out;
int threshold_div;
int temp;
switch (termios->c_cflag & CSIZE) {
default:
case CS8:
config_reg |= SIRFUART_DATA_BIT_LEN_8;
break;
case CS7:
config_reg |= SIRFUART_DATA_BIT_LEN_7;
break;
case CS6:
config_reg |= SIRFUART_DATA_BIT_LEN_6;
break;
case CS5:
config_reg |= SIRFUART_DATA_BIT_LEN_5;
break;
}
if (termios->c_cflag & CSTOPB)
config_reg |= SIRFUART_STOP_BIT_LEN_2;
baud_rate = uart_get_baud_rate(port, termios, old, 0, 4000000);
spin_lock_irqsave(&port->lock, flags);
port->read_status_mask = SIRFUART_RX_OFLOW_INT;
port->ignore_status_mask = 0;
/* read flags */
if (termios->c_iflag & INPCK)
port->read_status_mask |=
SIRFUART_FRM_ERR_INT | SIRFUART_PARITY_ERR_INT;
if (termios->c_iflag & (BRKINT | PARMRK))
port->read_status_mask |= SIRFUART_RXD_BREAK_INT;
/* ignore flags */
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |=
SIRFUART_FRM_ERR_INT | SIRFUART_PARITY_ERR_INT;
if ((termios->c_cflag & CREAD) == 0)
port->ignore_status_mask |= SIRFUART_DUMMY_READ;
/* enable parity if PARENB is set*/
if (termios->c_cflag & PARENB) {
if (termios->c_cflag & CMSPAR) {
if (termios->c_cflag & PARODD)
config_reg |= SIRFUART_STICK_BIT_MARK;
else
config_reg |= SIRFUART_STICK_BIT_SPACE;
} else if (termios->c_cflag & PARODD) {
config_reg |= SIRFUART_STICK_BIT_ODD;
} else {
config_reg |= SIRFUART_STICK_BIT_EVEN;
}
}
/* Hardware Flow Control Settings */
if (UART_ENABLE_MS(port, termios->c_cflag)) {
if (!sirfport->ms_enabled)
sirfsoc_uart_enable_ms(port);
} else {
if (sirfport->ms_enabled)
sirfsoc_uart_disable_ms(port);
}
if (port->uartclk == 150000000) {
/* common rate: fast calculation */
for (ic = 0; ic < SIRF_BAUD_RATE_SUPPORT_NR; ic++)
if (baud_rate == baudrate_to_regv[ic].baud_rate)
clk_div_reg = baudrate_to_regv[ic].reg_val;
}
setted_baud = baud_rate;
/* arbitary rate setting */
if (unlikely(clk_div_reg == 0))
clk_div_reg = sirfsoc_calc_sample_div(baud_rate, port->uartclk,
&setted_baud);
wr_regl(port, SIRFUART_DIVISOR, clk_div_reg);
if (tty_termios_baud_rate(termios))
tty_termios_encode_baud_rate(termios, setted_baud, setted_baud);
/* set receive timeout */
rx_time_out = SIRFSOC_UART_RX_TIMEOUT(baud_rate, 20000);
rx_time_out = (rx_time_out > 0xFFFF) ? 0xFFFF : rx_time_out;
config_reg |= SIRFUART_RECV_TIMEOUT(rx_time_out);
temp_reg_val = rd_regl(port, SIRFUART_TX_FIFO_OP);
wr_regl(port, SIRFUART_RX_FIFO_OP, 0);
wr_regl(port, SIRFUART_TX_FIFO_OP,
temp_reg_val & ~SIRFUART_TX_FIFO_START);
wr_regl(port, SIRFUART_TX_DMA_IO_CTRL, SIRFUART_TX_MODE_IO);
wr_regl(port, SIRFUART_RX_DMA_IO_CTRL, SIRFUART_RX_MODE_IO);
wr_regl(port, SIRFUART_LINE_CTRL, config_reg);
/* Reset Rx/Tx FIFO Threshold level for proper baudrate */
if (baud_rate < 1000000)
threshold_div = 1;
else
threshold_div = 2;
temp = port->line == 1 ? 16 : 64;
wr_regl(port, SIRFUART_TX_FIFO_CTRL, temp / threshold_div);
wr_regl(port, SIRFUART_RX_FIFO_CTRL, temp / threshold_div);
temp_reg_val |= SIRFUART_TX_FIFO_START;
wr_regl(port, SIRFUART_TX_FIFO_OP, temp_reg_val);
uart_update_timeout(port, termios->c_cflag, baud_rate);
sirfsoc_uart_start_rx(port);
wr_regl(port, SIRFUART_TX_RX_EN, SIRFUART_TX_EN | SIRFUART_RX_EN);
spin_unlock_irqrestore(&port->lock, flags);
}
static void sirfsoc_uart_set_termios(struct uart_port *port,
struct ktermios *termios,
struct ktermios *old)
{
struct sirfsoc_uart_port *sirfport = to_sirfport(port);
struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg;
struct sirfsoc_int_en *uint_en = &sirfport->uart_reg->uart_int_en;
unsigned long config_reg = 0;
unsigned long baud_rate;
unsigned long set_baud;
unsigned long flags;
unsigned long ic;
unsigned int clk_div_reg = 0;
unsigned long txfifo_op_reg, ioclk_rate;
unsigned long rx_time_out;
int threshold_div;
u32 data_bit_len, stop_bit_len, len_val;
unsigned long sample_div_reg = 0xf;
ioclk_rate = port->uartclk;
switch (termios->c_cflag & CSIZE) {
default:
case CS8:
data_bit_len = 8;
config_reg |= SIRFUART_DATA_BIT_LEN_8;
break;
case CS7:
data_bit_len = 7;
config_reg |= SIRFUART_DATA_BIT_LEN_7;
break;
case CS6:
data_bit_len = 6;
config_reg |= SIRFUART_DATA_BIT_LEN_6;
break;
case CS5:
data_bit_len = 5;
config_reg |= SIRFUART_DATA_BIT_LEN_5;
break;
}
if (termios->c_cflag & CSTOPB) {
config_reg |= SIRFUART_STOP_BIT_LEN_2;
stop_bit_len = 2;
} else
stop_bit_len = 1;
spin_lock_irqsave(&port->lock, flags);
port->read_status_mask = uint_en->sirfsoc_rx_oflow_en;
port->ignore_status_mask = 0;
if (sirfport->uart_reg->uart_type == SIRF_REAL_UART) {
if (termios->c_iflag & INPCK)
port->read_status_mask |= uint_en->sirfsoc_frm_err_en |
uint_en->sirfsoc_parity_err_en;
} else {
if (termios->c_iflag & INPCK)
port->read_status_mask |= uint_en->sirfsoc_frm_err_en;
}
if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
port->read_status_mask |= uint_en->sirfsoc_rxd_brk_en;
if (sirfport->uart_reg->uart_type == SIRF_REAL_UART) {
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |=
uint_en->sirfsoc_frm_err_en |
uint_en->sirfsoc_parity_err_en;
if (termios->c_cflag & PARENB) {
if (termios->c_cflag & CMSPAR) {
if (termios->c_cflag & PARODD)
config_reg |= SIRFUART_STICK_BIT_MARK;
else
config_reg |= SIRFUART_STICK_BIT_SPACE;
} else if (termios->c_cflag & PARODD) {
config_reg |= SIRFUART_STICK_BIT_ODD;
} else {
config_reg |= SIRFUART_STICK_BIT_EVEN;
}
}
} else {
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |=
uint_en->sirfsoc_frm_err_en;
if (termios->c_cflag & PARENB)
dev_warn(port->dev,
"USP-UART not support parity err\n");
}
if (termios->c_iflag & IGNBRK) {
port->ignore_status_mask |=
uint_en->sirfsoc_rxd_brk_en;
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |=
uint_en->sirfsoc_rx_oflow_en;
}
if ((termios->c_cflag & CREAD) == 0)
port->ignore_status_mask |= SIRFUART_DUMMY_READ;
/* Hardware Flow Control Settings */
if (UART_ENABLE_MS(port, termios->c_cflag)) {
if (!sirfport->ms_enabled)
sirfsoc_uart_enable_ms(port);
} else {
if (sirfport->ms_enabled)
sirfsoc_uart_disable_ms(port);
}
baud_rate = uart_get_baud_rate(port, termios, old, 0, 4000000);
if (ioclk_rate == 150000000) {
for (ic = 0; ic < SIRF_BAUD_RATE_SUPPORT_NR; ic++)
if (baud_rate == baudrate_to_regv[ic].baud_rate)
clk_div_reg = baudrate_to_regv[ic].reg_val;
}
set_baud = baud_rate;
if (sirfport->uart_reg->uart_type == SIRF_REAL_UART) {
if (unlikely(clk_div_reg == 0))
clk_div_reg = sirfsoc_uart_calc_sample_div(baud_rate,
ioclk_rate, &set_baud);
wr_regl(port, ureg->sirfsoc_divisor, clk_div_reg);
} else {
clk_div_reg = sirfsoc_usp_calc_sample_div(baud_rate,
ioclk_rate, &sample_div_reg);
sample_div_reg--;
set_baud = ((ioclk_rate / (clk_div_reg+1) - 1) /
(sample_div_reg + 1));
/* setting usp mode 2 */
len_val = ((1 << SIRFSOC_USP_MODE2_RXD_DELAY_OFFSET) |
(1 << SIRFSOC_USP_MODE2_TXD_DELAY_OFFSET));
len_val |= ((clk_div_reg & SIRFSOC_USP_MODE2_CLK_DIVISOR_MASK)
<< SIRFSOC_USP_MODE2_CLK_DIVISOR_OFFSET);
wr_regl(port, ureg->sirfsoc_mode2, len_val);
}
if (tty_termios_baud_rate(termios))
tty_termios_encode_baud_rate(termios, set_baud, set_baud);
/* set receive timeout && data bits len */
rx_time_out = SIRFSOC_UART_RX_TIMEOUT(set_baud, 20000);
rx_time_out = SIRFUART_RECV_TIMEOUT_VALUE(rx_time_out);
txfifo_op_reg = rd_regl(port, ureg->sirfsoc_tx_fifo_op);
wr_regl(port, ureg->sirfsoc_rx_fifo_op, SIRFUART_FIFO_STOP);
wr_regl(port, ureg->sirfsoc_tx_fifo_op,
(txfifo_op_reg & ~SIRFUART_FIFO_START));
if (sirfport->uart_reg->uart_type == SIRF_REAL_UART) {
config_reg |= SIRFUART_RECV_TIMEOUT(port, rx_time_out);
wr_regl(port, ureg->sirfsoc_line_ctrl, config_reg);
} else {
/*tx frame ctrl*/
len_val = (data_bit_len - 1) << SIRFSOC_USP_TX_DATA_LEN_OFFSET;
len_val |= (data_bit_len + 1 + stop_bit_len - 1) <<
SIRFSOC_USP_TX_FRAME_LEN_OFFSET;
len_val |= ((data_bit_len - 1) <<
SIRFSOC_USP_TX_SHIFTER_LEN_OFFSET);
len_val |= (((clk_div_reg & 0xc00) >> 10) <<
SIRFSOC_USP_TX_CLK_DIVISOR_OFFSET);
wr_regl(port, ureg->sirfsoc_tx_frame_ctrl, len_val);
/*rx frame ctrl*/
len_val = (data_bit_len - 1) << SIRFSOC_USP_RX_DATA_LEN_OFFSET;
len_val |= (data_bit_len + 1 + stop_bit_len - 1) <<
SIRFSOC_USP_RX_FRAME_LEN_OFFSET;
len_val |= (data_bit_len - 1) <<
SIRFSOC_USP_RX_SHIFTER_LEN_OFFSET;
len_val |= (((clk_div_reg & 0xf000) >> 12) <<
SIRFSOC_USP_RX_CLK_DIVISOR_OFFSET);
wr_regl(port, ureg->sirfsoc_rx_frame_ctrl, len_val);
/*async param*/
wr_regl(port, ureg->sirfsoc_async_param_reg,
(SIRFUART_RECV_TIMEOUT(port, rx_time_out)) |
(sample_div_reg & SIRFSOC_USP_ASYNC_DIV2_MASK) <<
SIRFSOC_USP_ASYNC_DIV2_OFFSET);
}
if (sirfport->tx_dma_chan)
wr_regl(port, ureg->sirfsoc_tx_dma_io_ctrl, SIRFUART_DMA_MODE);
else
wr_regl(port, ureg->sirfsoc_tx_dma_io_ctrl, SIRFUART_IO_MODE);
if (sirfport->rx_dma_chan)
wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl, SIRFUART_DMA_MODE);
else
wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl, SIRFUART_IO_MODE);
/* Reset Rx/Tx FIFO Threshold level for proper baudrate */
if (set_baud < 1000000)
threshold_div = 1;
else
threshold_div = 2;
wr_regl(port, ureg->sirfsoc_tx_fifo_ctrl,
SIRFUART_FIFO_THD(port) / threshold_div);
wr_regl(port, ureg->sirfsoc_rx_fifo_ctrl,
SIRFUART_FIFO_THD(port) / threshold_div);
txfifo_op_reg |= SIRFUART_FIFO_START;
wr_regl(port, ureg->sirfsoc_tx_fifo_op, txfifo_op_reg);
uart_update_timeout(port, termios->c_cflag, set_baud);
sirfsoc_uart_start_rx(port);
wr_regl(port, ureg->sirfsoc_tx_rx_en, SIRFUART_TX_EN | SIRFUART_RX_EN);
spin_unlock_irqrestore(&port->lock, flags);
}