static void spi_setup(void)
{
/* The DOGM128 display is connected to SPI2, so initialise it. */
rcc_peripheral_enable_clock(&RCC_APB1ENR, RCC_APB1ENR_SPI2EN);
spi_set_unidirectional_mode(DOGM128_SPI); /* We want to send only. */
spi_disable_crc(DOGM128_SPI); /* No CRC for this slave. */
spi_set_dff_8bit(DOGM128_SPI); /* 8-bit dataword-length */
spi_set_full_duplex_mode(DOGM128_SPI); /* Not receive-only */
/* We want to handle the CS signal in software. */
spi_enable_software_slave_management(DOGM128_SPI);
spi_set_nss_high(DOGM128_SPI);
/* PCLOCK/256 as clock. */
spi_set_baudrate_prescaler(DOGM128_SPI, SPI_CR1_BR_FPCLK_DIV_256);
/* We want to control everything and generate the clock -> master. */
spi_set_master_mode(DOGM128_SPI);
spi_set_clock_polarity_1(DOGM128_SPI); /* SCK idle state high. */
/* Bit is taken on the second (rising edge) of SCK. */
spi_set_clock_phase_1(DOGM128_SPI);
spi_enable_ss_output(DOGM128_SPI);
spi_enable(DOGM128_SPI);
}
int devspi_create(const struct spi_config *conf)
{
struct dev_spi *spi = NULL;
if (!conf)
return -EINVAL;
if (conf->base == 0)
return -EINVAL;
if ((conf->idx < 0) || (conf->idx > MAX_SPIS))
return -EINVAL;
spi = kalloc(sizeof(struct dev_spi));
if (!spi)
return -ENOMEM;
/* Claim pins for SCK/MOSI/MISO */
gpio_create(&mod_spi, &conf->pio_sck);
gpio_create(&mod_spi, &conf->pio_mosi);
gpio_create(&mod_spi, &conf->pio_miso);
/* Erase spi content */
memset(spi, 0, sizeof(struct dev_spi));
/* Enable clocks */
rcc_periph_clock_enable(conf->rcc);
rcc_periph_clock_enable(conf->dma_rcc);
/* Startup routine */
//spi_disable(conf->base);
/**********************************/
/* reset SPI1 */
spi_reset(conf->base);
/* init SPI1 master */
spi_init_master(conf->base,
SPI_CR1_BAUDRATE_FPCLK_DIV_64,
SPI_CR1_CPOL_CLK_TO_0_WHEN_IDLE,
SPI_CR1_CPHA_CLK_TRANSITION_1,
SPI_CR1_DFF_8BIT,
SPI_CR1_MSBFIRST);
/* enable SPI1 first */
spi_enable(conf->base);
/**********************************/
#if 0
spi_set_master_mode(conf->base);
spi_set_baudrate_prescaler(conf->base, SPI_CR1_BR_FPCLK_DIV_256); /* TODO: Calculate prescaler from baudrate */
if(conf->polarity == 0)
spi_set_clock_polarity_0(conf->base);
else
spi_set_clock_polarity_1(conf->base);
if(conf->phase == 0) spi_set_clock_phase_0(conf->base);
else
spi_set_clock_phase_1(conf->base);
if(conf->rx_only == 0)
spi_set_full_duplex_mode(conf->base);
else
spi_set_receive_only_mode(conf->base);
if(conf->bidir_mode == 0)
spi_set_unidirectional_mode(conf->base);
else
spi_set_bidirectional_mode(conf->base);
if(conf->dff_16)
spi_set_dff_16bit(conf->base);
else
spi_set_dff_8bit(conf->base);
if(conf->enable_software_slave_management)
spi_enable_software_slave_management(conf->base);
else
spi_disable_software_slave_management(conf->base);
if(conf->send_msb_first)
spi_send_msb_first(conf->base);
else
spi_send_lsb_first(conf->base);
spi_set_nss_high(conf->base);
#endif
/* Set up device struct */
spi->base = conf->base;
spi->irq = conf->irq;
//spi->tx_dma_config = &conf->tx_dma;
//spi->rx_dma_config = &conf->rx_dma;
spi->mutex = mutex_init();
/* Store address in the DEV_SPI array. */
DEV_SPI[conf->idx] = spi;
/* Enable interrupts */
//nvic_set_priority(conf->irq, 1);
//nvic_enable_irq(conf->irq);
return 0;
}
