static void configure_tc(struct tc_module *tc_instance)
{
//! [setup_6]
struct tc_config config_tc;
struct tc_events config_events;
//! [setup_6]
//! [setup_7]
tc_get_config_defaults(&config_tc);
//! [setup_7]
//! [setup_8]
config_tc.counter_size = TC_COUNTER_SIZE_8BIT;
config_tc.wave_generation = TC_WAVE_GENERATION_NORMAL_FREQ;
config_tc.clock_source = GCLK_GENERATOR_1;
config_tc.clock_prescaler = TC_CLOCK_PRESCALER_DIV64;
//! [setup_8]
//! [setup_9]
tc_init(tc_instance, CONF_TC_MODULE, &config_tc);
//! [setup_9]
//! [setup_10]
config_events.generate_event_on_overflow = true;
tc_enable_events(tc_instance, &config_events);
//! [setup_10]
//! [setup_11]
tc_enable(tc_instance);
//! [setup_11]
}
/** Initializes the XOSC32K crystal failure detector, and starts it.
*
* \param[in] ok_callback Callback function to run upon XOSC32K operational
* \param[in] fail_callback Callback function to run upon XOSC32K failure
*/
static void init_xosc32k_fail_detector(
const tc_callback_t ok_callback,
const tc_callback_t fail_callback)
{
/* TC pairs share the same clock, ensure reference and crystal timers use
* different clocks */
Assert(Abs(_tc_get_inst_index(CONF_TC_OSC32K) -
_tc_get_inst_index(CONF_TC_XOSC32K)) >= 2);
/* The crystal detection cycle count must be less than the reference cycle
* count, so that the reference timer is periodically reset before expiry */
Assert(CRYSTAL_RESET_CYCLES < CRYSTAL_FAIL_CYCLES);
/* Must use different clock generators for the crystal and reference, must
* not be CPU generator 0 */
Assert(GCLK_GENERATOR_XOSC32K != GCLK_GENERATOR_OSC32K);
Assert(GCLK_GENERATOR_XOSC32K != GCLK_GENERATOR_0);
Assert(GCLK_GENERATOR_OSC32K != GCLK_GENERATOR_0);
/* Configure and enable the XOSC32K GCLK generator */
struct system_gclk_gen_config xosc32k_gen_conf;
system_gclk_gen_get_config_defaults(&xosc32k_gen_conf);
xosc32k_gen_conf.source_clock = SYSTEM_CLOCK_SOURCE_XOSC32K;
system_gclk_gen_set_config(GCLK_GENERATOR_XOSC32K, &xosc32k_gen_conf);
system_gclk_gen_enable(GCLK_GENERATOR_XOSC32K);
/* Configure and enable the reference clock GCLK generator */
struct system_gclk_gen_config ref_gen_conf;
system_gclk_gen_get_config_defaults(&ref_gen_conf);
ref_gen_conf.source_clock = SYSTEM_CLOCK_SOURCE_OSC32K;
system_gclk_gen_set_config(GCLK_GENERATOR_OSC32K, &ref_gen_conf);
system_gclk_gen_enable(GCLK_GENERATOR_OSC32K);
/* Set up crystal counter - when target count elapses, trigger event */
struct tc_config tc_xosc32k_conf;
tc_get_config_defaults(&tc_xosc32k_conf);
tc_xosc32k_conf.clock_source = GCLK_GENERATOR_XOSC32K;
tc_xosc32k_conf.counter_16_bit.compare_capture_channel[0] =
CRYSTAL_RESET_CYCLES;
tc_xosc32k_conf.wave_generation = TC_WAVE_GENERATION_MATCH_FREQ;
tc_init(&tc_xosc32k, CONF_TC_XOSC32K, &tc_xosc32k_conf);
/* Set up reference counter - when event received, restart */
struct tc_config tc_osc32k_conf;
tc_get_config_defaults(&tc_osc32k_conf);
tc_osc32k_conf.clock_source = GCLK_GENERATOR_OSC32K;
tc_osc32k_conf.counter_16_bit.compare_capture_channel[0] =
CRYSTAL_FAIL_CYCLES;
tc_osc32k_conf.wave_generation = TC_WAVE_GENERATION_MATCH_FREQ;
tc_init(&tc_osc32k, CONF_TC_OSC32K, &tc_osc32k_conf);
/* Configure event channel and link it to the xosc32k counter */
struct events_config config;
struct events_resource event;
events_get_config_defaults(&config);
config.edge_detect = EVENTS_EDGE_DETECT_NONE;
config.generator = CONF_EVENT_GENERATOR_ID;
config.path = EVENTS_PATH_ASYNCHRONOUS;
events_allocate(&event, &config);
/* Configure event user and link it to the osc32k counter */
events_attach_user(&event, CONF_EVENT_USED_ID);
/* Enable event generation for crystal counter */
struct tc_events tc_xosc32k_events = { .generate_event_on_overflow = true };
tc_enable_events(&tc_xosc32k, &tc_xosc32k_events);
/* Enable event reception for reference counter */
struct tc_events tc_osc32k_events = { .on_event_perform_action = true };
tc_osc32k_events.event_action = TC_EVENT_ACTION_RETRIGGER;
tc_enable_events(&tc_osc32k, &tc_osc32k_events);
/* Enable overflow callback for the crystal counter - if crystal count
* has been reached, crystal is operational */
tc_register_callback(&tc_xosc32k, ok_callback, TC_CALLBACK_CC_CHANNEL0);
tc_enable_callback(&tc_xosc32k, TC_CALLBACK_CC_CHANNEL0);
/* Enable compare callback for the reference counter - if reference count
* has been reached, crystal has failed */
tc_register_callback(&tc_osc32k, fail_callback, TC_CALLBACK_CC_CHANNEL0);
tc_enable_callback(&tc_osc32k, TC_CALLBACK_CC_CHANNEL0);
/* Start both crystal and reference counters */
tc_enable(&tc_xosc32k);
tc_enable(&tc_osc32k);
}
/** Main application entry point. */
int main(void)
{
system_init();
system_flash_set_waitstates(2);
init_osc32k();
init_xosc32k();
init_xosc32k_fail_detector(
xosc32k_ok_callback, xosc32k_fail_callback);
#if ENABLE_CPU_CLOCK_OUT == true
/* Configure a GPIO pin as the CPU clock output */
struct system_pinmux_config clk_out_pin;
system_pinmux_get_config_defaults(&clk_out_pin);
clk_out_pin.direction = SYSTEM_PINMUX_PIN_DIR_OUTPUT;
clk_out_pin.mux_position = CONF_CLOCK_PIN_MUX;
system_pinmux_pin_set_config(CONF_CLOCK_PIN_OUT, &clk_out_pin);
#endif
for (;;) {
static bool old_run_osc = true;
bool new_run_osc =
(port_pin_get_input_level(BUTTON_0_PIN) == BUTTON_0_INACTIVE);
/* Check if the XOSC32K needs to be started or stopped when the board
* button is pressed or released */
if (new_run_osc != old_run_osc) {
if (new_run_osc) {
system_clock_source_enable(SYSTEM_CLOCK_SOURCE_XOSC32K);
while(!system_clock_source_is_ready(
SYSTEM_CLOCK_SOURCE_XOSC32K));
}
else {
system_clock_source_disable(SYSTEM_CLOCK_SOURCE_XOSC32K);
}
old_run_osc = new_run_osc;
}
}
}
/**
* \brief Configures the DAC in event triggered mode.
*
* Configures the DAC to use the module's default configuration, with output
* channel mode configured for event triggered conversions.
*
* \param dev_inst Pointer to the DAC module software instance to initialize
*/
static void configure_dac(struct dac_module *dac_module)
{
struct dac_config config;
struct dac_chan_config channel_config;
/* Get the DAC default configuration */
dac_get_config_defaults(&config);
/* Switch to GCLK generator 0 */
config.clock_source = GCLK_GENERATOR_0;
dac_init(dac_module, DAC, &config);
/* Get the default DAC channel config */
dac_chan_get_config_defaults(&channel_config);
/* Set the channel configuration, and enable it */
dac_chan_set_config(dac_module, DAC_CHANNEL_0, &channel_config);
dac_chan_enable(dac_module, DAC_CHANNEL_0);
/* Enable event triggered conversions */
struct dac_events events = { .on_event_start_conversion = true };
dac_enable_events(dac_module, &events);
dac_enable(dac_module);
}
/**
* \brief Configures the TC to generate output events at the sample frequency.
*
* Configures the TC in Frequency Generation mode, with an event output once
* each time the audio sample frequency period expires.
*
* \param dev_inst Pointer to the TC module software instance to initialize
*/
static void configure_tc(struct tc_module *tc_module)
{
struct tc_config config;
tc_get_config_defaults(&config);
config.clock_source = GCLK_GENERATOR_0;
config.wave_generation = TC_WAVE_GENERATION_MATCH_FREQ;
tc_init(tc_module, TC3, &config);
/* Enable periodic event output generation */
struct tc_events events = { .generate_event_on_overflow = true };
tc_enable_events(tc_module, &events);
/* Set the timer top value to alter the overflow frequency */
tc_set_top_value(tc_module,
system_gclk_gen_get_hz(GCLK_GENERATOR_0) / sample_rate);
tc_enable(tc_module);
}
/**
* \brief Configures the event system to link the sample timer to the DAC.
*
* Configures the event system, linking the TC module used for the audio sample
* rate timing to the DAC, so that a new conversion is triggered each time the
* DAC receives an event from the timer.
*/
static void configure_events(struct events_resource *event)
{
struct events_config config;
events_get_config_defaults(&config);
config.generator = EVSYS_ID_GEN_TC3_OVF;
config.path = EVENTS_PATH_ASYNCHRONOUS;
events_allocate(event, &config);
events_attach_user(event, EVSYS_ID_USER_DAC_START);
}
/**
* \brief Main application routine
*/
int main(void)
{
struct dac_module dac_module;
struct tc_module tc_module;
struct events_resource event;
/* Initialize all the system clocks, pm, gclk... */
system_init();
/* Enable the internal bandgap to use as reference to the DAC */
system_voltage_reference_enable(SYSTEM_VOLTAGE_REFERENCE_BANDGAP);
/* Module configuration */
configure_tc(&tc_module);
configure_dac(&dac_module);
configure_events(&event);
/* Start the sample trigger timer */
tc_start_counter(&tc_module);
while (true) {
while (port_pin_get_input_level(SW0_PIN) == SW0_INACTIVE) {
/* Wait for the button to be pressed */
}
port_pin_toggle_output_level(LED0_PIN);
for (uint32_t i = 0; i < number_of_samples; i++) {
dac_chan_write(&dac_module, DAC_CHANNEL_0, wav_samples[i]);
while (!(DAC->INTFLAG.reg & DAC_INTFLAG_EMPTY)) {
/* Wait for data buffer to be empty */
}
}
while (port_pin_get_input_level(SW0_PIN) == SW0_ACTIVE) {
/* Wait for the button to be depressed */
}
}
}
/**
* \brief Initialize the TC3 & RTC for unit test
*
* Initializes the RTC module and TC3 module which are used as
* event generator and event user respectively.
*/
static void test_event_gen_user_init(void)
{
enum status_code status;
init_success = true;
/* Timer configuration (Event User) */
struct tc_config config_tc;
tc_get_config_defaults(&config_tc);
config_tc.counter_16_bit.compare_capture_channel[0]
= (0xFFFF / 4);
/* Initialize the TC3 */
status = tc_init(&tc_inst, TC3, &config_tc);
if (status != STATUS_OK) {
init_success = false;
}
struct tc_events events_tc;
events_tc.on_event_perform_action = true;
events_tc.event_action = TC_EVENT_ACTION_START;
tc_enable_events(&tc_inst, &events_tc);
/* Enable the TC3 */
tc_enable(&tc_inst);
/* RTC configuration (Event Generator) */
struct rtc_count_config config_rtc_count;
struct rtc_count_events config_rtc_event
= { .generate_event_on_overflow = true };
/* Initialize the RTC module */
rtc_count_get_config_defaults(&config_rtc_count);
config_rtc_count.prescaler = RTC_COUNT_PRESCALER_DIV_1;
config_rtc_count.mode = RTC_COUNT_MODE_16BIT;
#ifdef FEATURE_RTC_CONTINUOUSLY_UPDATED
config_rtc_count.continuously_update = true;
#endif
config_rtc_count.compare_values[0] = 50;
status = rtc_count_init(&rtc_inst, RTC, &config_rtc_count);
if (status != STATUS_OK) {
init_success = false;
}
/* Enable RTC events */
config_rtc_event.generate_event_on_overflow = true;
rtc_count_enable_events(&rtc_inst, &config_rtc_event);
}
/**
* \internal
* \brief Setup Function: Synchronous event propagation.
*
* This function initializes the event system channel 0 and the RTC
* module (event generator) to be in the same clock domain for
* synchronous event propagation.
*
* \param test Current test case.
*/
static void setup_synchronous_event_test(const struct test_case *test)
{
struct events_config events_conf;
/* Get default event channel configuration */
events_get_config_defaults(&events_conf);
events_conf.clock_source = GCLK_GENERATOR_2;
events_conf.edge_detect = EVENTS_EDGE_DETECT_RISING;
events_conf.path = EVENTS_PATH_SYNCHRONOUS;
events_conf.generator = TEST_EVENT_GEN;
events_allocate(&events, &events_conf);
events_attach_user(&events, TEST_EVENT_USER);
}
/**
* \internal
* \brief Test for event system in synchronous mode.
*
* This test waits for event channel and user to be ready and then
* starts the RTC to generate overflow event. It waits until the timer
* is started. If the timer starts running then it can be assumed that
* the event has been propagated properly.
*
* \param test Current test case.
*/
static void run_synchronous_event_test(const struct test_case *test)
{
uint32_t timeout_cycles = 1000;
/* Skip test if initialization failed */
test_assert_true(test, init_success,
"Skipping test due to failed initialization");
/* Check whether event user is ready */
do {
timeout_cycles--;
if (events_is_users_ready(&events)) {
break;
}
} while (timeout_cycles > 0);
test_assert_true(test, timeout_cycles > 0,
"Timeout error: Event user not ready");
/* Check whether event channel is ready */
timeout_cycles = 1000;
do {
timeout_cycles--;
if (!events_is_busy(&events)) {
break;
}
} while (timeout_cycles > 0);
test_assert_true(test, timeout_cycles > 0,
"Timeout error: Event channel not ready");
/* Event action test */
rtc_count_enable(&rtc_inst);
rtc_count_set_period(&rtc_inst, 100);
timeout_cycles = 10000;
do {
timeout_cycles--;
if (tc_get_count_value(&tc_inst)) {
break;
}
} while (timeout_cycles > 0);
test_assert_true(test, timeout_cycles > 0,
"Error: Timeout in event reception/action");
}
/**
* \internal
* \brief Test capture and compare
*
* This test uses TC module 0 as a PWM generator (compare function).
* TC module 1 will be set to capture the signal from TC module 0 to test the capture
* functionality.
*
* \param test Current test case.
*/
static void run_16bit_capture_and_compare_test(const struct test_case *test)
{
test_assert_true(test,
tc_init_success == true,
"TC initialization failed, skipping test");
test_assert_true(test,
callback_function_entered == 1,
"The callback test has failed, skipping test");
/* Configure 16-bit TC module for PWM generation */
tc_reset(&tc_test0_module);
tc_get_config_defaults(&tc_test0_config);
tc_test0_config.wave_generation = TC_WAVE_GENERATION_MATCH_PWM;
tc_test0_config.counter_16_bit.compare_capture_channel[TC_COMPARE_CAPTURE_CHANNEL_0] = 0x03FF;
tc_test0_config.counter_16_bit.compare_capture_channel[TC_COMPARE_CAPTURE_CHANNEL_1] = 0x01FF;
/* Calculate the theoretical PWM frequency & duty */
uint32_t frequency_output, duty_output;
frequency_output = system_clock_source_get_hz(SYSTEM_CLOCK_SOURCE_OSC8M)/ (0x03FF+1);
/* This value is depend on the WaveGeneration Mode */
duty_output = (uint32_t)(tc_test0_config.counter_16_bit.compare_capture_channel[TC_COMPARE_CAPTURE_CHANNEL_1]) * 100 \
/ tc_test0_config.counter_16_bit.compare_capture_channel[TC_COMPARE_CAPTURE_CHANNEL_0];
tc_test0_config.pwm_channel[TC_COMPARE_CAPTURE_CHANNEL_1].enabled = true;
tc_test0_config.pwm_channel[TC_COMPARE_CAPTURE_CHANNEL_1].pin_out = CONF_TEST_PIN_OUT;
tc_test0_config.pwm_channel[TC_COMPARE_CAPTURE_CHANNEL_1].pin_mux = CONF_TEST_PIN_MUX;
tc_init(&tc_test0_module, CONF_TEST_TC0, &tc_test0_config);
tc_register_callback(&tc_test0_module, tc_callback_function, TC_CALLBACK_CC_CHANNEL0);
tc_enable_callback(&tc_test0_module, TC_CALLBACK_CC_CHANNEL0);
/* Configure 16-bit TC module for capture */
tc_reset(&tc_test1_module);
tc_get_config_defaults(&tc_test1_config);
tc_test1_config.clock_prescaler = TC_CLOCK_PRESCALER_DIV1;
tc_test1_config.enable_capture_on_channel[CONF_CAPTURE_CHAN_0] = true;
tc_test1_config.enable_capture_on_channel[CONF_CAPTURE_CHAN_1] = true;
tc_init(&tc_test1_module, CONF_TEST_TC1, &tc_test1_config);
struct tc_events tc_events = { .on_event_perform_action = true,
.event_action = TC_EVENT_ACTION_PPW,};
tc_enable_events(&tc_test1_module, &tc_events);
/* Configure external interrupt controller */
struct extint_chan_conf extint_chan_config;
extint_chan_config.gpio_pin = CONF_EIC_PIN;
extint_chan_config.gpio_pin_mux = CONF_EIC_MUX;
extint_chan_config.gpio_pin_pull = EXTINT_PULL_UP;
extint_chan_config.wake_if_sleeping = false;
extint_chan_config.filter_input_signal = false;
extint_chan_config.detection_criteria = EXTINT_DETECT_HIGH;
extint_chan_set_config(0, &extint_chan_config);
/* Configure external interrupt module to be event generator */
struct extint_events extint_event_conf;
extint_event_conf.generate_event_on_detect[0] = true;
extint_enable_events(&extint_event_conf);
/* Configure event system */
struct events_resource event_res;
/* Configure channel */
struct events_config config;
events_get_config_defaults(&config);
config.generator = CONF_EVENT_GENERATOR_ID;
config.edge_detect = EVENTS_EDGE_DETECT_NONE;
config.path = EVENTS_PATH_ASYNCHRONOUS;
events_allocate(&event_res, &config);
/* Configure user */
events_attach_user(&event_res, CONF_EVENT_USED_ID);
/* Enable TC modules */
tc_enable(&tc_test1_module);
tc_enable(&tc_test0_module);
uint16_t period_after_capture = 0;
uint16_t pulse_width_after_capture = 0;
uint32_t capture_frequency = 0;
uint32_t capture_duty = 0;
while (callback_function_entered < 4) {
period_after_capture = tc_get_capture_value(&tc_test1_module,
TC_COMPARE_CAPTURE_CHANNEL_0);
pulse_width_after_capture = tc_get_capture_value(&tc_test1_module,
TC_COMPARE_CAPTURE_CHANNEL_1);
}
if(period_after_capture != 0) {
capture_frequency = system_clock_source_get_hz(SYSTEM_CLOCK_SOURCE_OSC8M)/ period_after_capture;
capture_duty = (uint32_t)(pulse_width_after_capture) * 100 / period_after_capture;
}
test_assert_true(test,
(capture_frequency <= (frequency_output * (100 + CONF_TEST_TOLERANCE) / 100)) && \
(capture_frequency >= (frequency_output * (100 - CONF_TEST_TOLERANCE) / 100)) && \
(capture_duty <= (duty_output * (100 + CONF_TEST_TOLERANCE) / 100)) && \
(capture_duty >= (duty_output * (100 - CONF_TEST_TOLERANCE) / 100)) \
,"The result of Capture is wrong, captured frequency: %ldHz, captured duty: %ld%%",
capture_frequency,
capture_duty
);
}
/**
* \brief Initialize the USART for unit test
*
* Initializes the SERCOM USART used for sending the unit test status to the
* computer via the EDBG CDC gateway.
*/
static void cdc_uart_init(void)
{
struct usart_config usart_conf;
/* Configure USART for unit test output */
usart_get_config_defaults(&usart_conf);
usart_conf.mux_setting = CONF_STDIO_MUX_SETTING;
usart_conf.pinmux_pad0 = CONF_STDIO_PINMUX_PAD0;
usart_conf.pinmux_pad1 = CONF_STDIO_PINMUX_PAD1;
usart_conf.pinmux_pad2 = CONF_STDIO_PINMUX_PAD2;
usart_conf.pinmux_pad3 = CONF_STDIO_PINMUX_PAD3;
usart_conf.baudrate = CONF_STDIO_BAUDRATE;
stdio_serial_init(&cdc_uart_module, CONF_STDIO_USART, &usart_conf);
usart_enable(&cdc_uart_module);
}
/**
* \brief Run TC unit tests
*
* Initializes the system and serial output, then sets up the TC unit test
* suite and runs it.
*/
int main(void)
{
system_init();
cdc_uart_init();
/* Define Test Cases */
DEFINE_TEST_CASE(init_test, NULL,
run_init_test, NULL,
"Initialize tc_xmodules");
DEFINE_TEST_CASE(basic_functionality_test, NULL,
run_basic_functionality_test, NULL,
"test start stop and getters and setters");
DEFINE_TEST_CASE(callback_test, NULL,
run_callback_test, NULL,
"test callback API");
DEFINE_TEST_CASE(reset_32bit_master_test, NULL,
run_reset_32bit_master_test, NULL,
"Setup, reset and reinitialize TC modules of a 32-bit TC");
DEFINE_TEST_CASE(capture_and_compare_test, NULL,
run_16bit_capture_and_compare_test, NULL,
"Test capture and compare");
/* Put test case addresses in an array */
DEFINE_TEST_ARRAY(tc_tests) = {
&init_test,
&basic_functionality_test,
&callback_test,
&reset_32bit_master_test,
&capture_and_compare_test,
};
/* Define the test suite */
DEFINE_TEST_SUITE(tc_suite, tc_tests,
"SAM TC driver test suite");
/* Run all tests in the suite*/
test_suite_run(&tc_suite);
tc_reset(&tc_test0_module);
tc_reset(&tc_test1_module);
while (true) {
/* Intentionally left empty */
}
}
/** Set up the measurement and comparison timer events.
* - Configure the reference timer to generate an event upon comparison
* match with channel 0.
* - Configure the measurement timer to trigger a capture when an event is
* received.
*/
static void setup_tc_events(void)
{
/* Enable incoming events on on measurement timer */
struct tc_events events_calib = { .on_event_perform_action = true };
tc_enable_events(&tc_calib, &events_calib);
/* Generate events from the reference timer on channel 0 compare match */
struct tc_events events_comp = { .generate_event_on_compare_channel[0] = true };
tc_enable_events(&tc_comp, &events_comp);
tc_enable(&tc_calib);
tc_enable(&tc_comp);
}
/** Set up the event system, linking the measurement and comparison timers so
* that events generated from the reference timer are linked to the measurement
* timer.
*/
static void setup_events(struct events_resource *event)
{
struct events_config config;
events_get_config_defaults(&config);
/* The event channel detects rising edges of the reference timer output
* event */
config.edge_detect = EVENTS_EDGE_DETECT_RISING;
config.path = EVENTS_PATH_SYNCHRONOUS;
config.generator = CONF_EVENT_GENERATOR_ID;
events_allocate(event, &config);
events_attach_user(event, CONF_EVENT_USED_ID);
}
/** Set up the USART for transmit-only communication at a fixed baud rate. */
static void setup_usart_channel(void)
{
struct usart_config cdc_uart_config;
usart_get_config_defaults(&cdc_uart_config);
/* Configure the USART settings and initialize the standard I/O library */
cdc_uart_config.mux_setting = EDBG_CDC_SERCOM_MUX_SETTING;
cdc_uart_config.pinmux_pad0 = EDBG_CDC_SERCOM_PINMUX_PAD0;
cdc_uart_config.pinmux_pad1 = EDBG_CDC_SERCOM_PINMUX_PAD1;
cdc_uart_config.pinmux_pad2 = EDBG_CDC_SERCOM_PINMUX_PAD2;
cdc_uart_config.pinmux_pad3 = EDBG_CDC_SERCOM_PINMUX_PAD3;
cdc_uart_config.baudrate = 115200;
stdio_serial_init(&usart_edbg, EDBG_CDC_MODULE, &cdc_uart_config);
usart_enable(&usart_edbg);
}
/** Set up the clock output pin so that the current system clock frequency can
* be monitored via an external frequency counter or oscilloscope. */
static void setup_clock_out_pin(void)
{
struct system_pinmux_config pin_mux;
system_pinmux_get_config_defaults(&pin_mux);
/* MUX out the system clock to a I/O pin of the device */
pin_mux.mux_position = CONF_CLOCK_PIN_MUX;
system_pinmux_pin_set_config(CONF_CLOCK_PIN_OUT, &pin_mux);
}
/** Retrieves the current system clock frequency, computed from the reference
* clock.
*
* \return Current system clock frequency in Hz.
*/
static uint32_t get_osc_frequency(void)
{
/* Clear any existing match status on the measurement timer */
tc_clear_status(&tc_comp, TC_STATUS_CHANNEL_0_MATCH);
/* Restart both measurement and reference timers */
tc_start_counter(&tc_calib);
tc_start_counter(&tc_comp);
/* Wait for the measurement timer to signal a compare match */
while (!(tc_get_status(&tc_comp) & TC_STATUS_CHANNEL_0_MATCH)) {
/* Wait for channel 0 match */
}
/* Compute the real clock frequency from the measurement timer count and
* reference count */
uint64_t tmp = tc_get_capture_value(&tc_calib, TC_COMPARE_CAPTURE_CHANNEL_0);
return ((tmp * REFERENCE_CLOCK_HZ) >> CALIBRATION_RESOLUTION);
}
int main(void)
{
struct events_resource event;
/* System initialization */
system_init();
delay_init();
/* Module initialization */
setup_tc_channels();
setup_tc_events();
setup_events(&event);
setup_clock_out_pin();
/* Init the variables with default calibration settings */
uint8_t frange_cal = SYSCTRL->OSC8M.bit.FRANGE;
uint8_t temp_cal = SYSCTRL->OSC8M.bit.CALIB >> TEMP_CAL_OFFSET;
uint8_t comm_cal = SYSCTRL->OSC8M.bit.CALIB & COMM_CAL_MAX;
/* Set the calibration test range */
uint8_t frange_cal_min = max((frange_cal - CONF_FRANGE_CAL), FRANGE_CAL_MIN);
uint8_t frange_cal_max = min((frange_cal + CONF_FRANGE_CAL), FRANGE_CAL_MAX);
uint8_t temp_cal_min = max((temp_cal - CONF_TEMP_CAL), TEMP_CAL_MIN);
uint8_t temp_cal_max = min((temp_cal + CONF_TEMP_CAL), TEMP_CAL_MAX);
/* Variables to track the previous and best calibration settings */
uint16_t comm_best = 0;
uint8_t frange_best = 0;
uint32_t freq_best = 0;
uint32_t freq_before = get_osc_frequency();
/* Run calibration loop */
for (frange_cal = frange_cal_min; frange_cal <= frange_cal_max; frange_cal++) {
for (temp_cal = temp_cal_min; temp_cal <= temp_cal_max; temp_cal++) {
for (comm_cal = COMM_CAL_MIN; comm_cal <= COMM_CAL_MAX; comm_cal++) {
/* Set the test calibration values */
system_clock_source_write_calibration(
SYSTEM_CLOCK_SOURCE_OSC8M, (temp_cal << 7) | comm_cal, frange_cal);
/* Wait for stabilization */
delay_cycles(1000);
/* Compute the deltas of the current and best system clock
* frequencies, save current settings if they are closer to the
* ideal frequency than the previous best values
*/
uint32_t freq_current = get_osc_frequency();
if (abs(freq_current - TARGET_FREQUENCY) < abs(freq_best - TARGET_FREQUENCY)) {
freq_best = freq_current;
comm_best = comm_cal;
frange_best = frange_cal;
port_pin_set_output_level(LED_0_PIN, LED_0_ACTIVE);
} else {
port_pin_set_output_level(LED_0_PIN, !LED_0_ACTIVE);
}
}
}
}
/* Set the found best calibration values */
system_clock_source_write_calibration(
SYSTEM_CLOCK_SOURCE_OSC8M, (temp_cal << 7) | comm_best, frange_best);
/* Setup USART module to output results */
setup_usart_channel();
/* Write previous and current frequency and new calibration settings to the
* USART
*/
printf("Freq Before: %lu\r\n", freq_before);
printf("Freq Best: %lu\r\n", freq_best);
printf("Freq Range: %u\r\n", frange_best);
printf("Calib Value: 0x%x\r\n", (temp_cal << 7) | comm_best);
/* Rapidly flash the board LED to signal the calibration completion */
while (1) {
port_pin_toggle_output_level(LED_0_PIN);
delay_ms(200);
}
}
/* Timer 0 Initialization */
void timer_init(void)
{
struct tc_config conf_tc;
struct tc_events conf_tc_events = {.generate_event_on_compare_channel[0] = 1};
tc_get_config_defaults(&conf_tc);
conf_tc.clock_source = GCLK_GENERATOR_0;
conf_tc.wave_generation = TC_WAVE_GENERATION_MATCH_FREQ;
conf_tc.counter_16_bit.compare_capture_channel[0] = 0xFFFF;
tc_init(&tc_inst, TC0, &conf_tc);
tc_enable_events(&tc_inst, &conf_tc_events);
tc_enable(&tc_inst);
tc_stop_counter(&tc_inst);
/* Enable TC0 match/capture channel 0 interrupt */
TC0->COUNT16.INTENSET.bit.MC0 = 1;
/* Enable TC0 module interrupt */
NVIC_EnableIRQ(TC0_IRQn);
}
/* DAC Initialization */
void dac_initialize(void)
{
struct dac_config conf_dac;
struct dac_events conf_dac_events = {.on_event_start_conversion = 1};
dac_get_config_defaults(&conf_dac);
conf_dac.clock_source = GCLK_GENERATOR_3;
conf_dac.reference = DAC_REFERENCE_INT1V;
dac_init(&dac_inst, DAC, &conf_dac);
dac_enable_events(&dac_inst, &conf_dac_events);
dac_enable(&dac_inst);
}
/* Event System Initialization */
void evsys_init(void)
{
struct events_resource conf_event_resource;
struct events_config conf_event;
events_get_config_defaults(&conf_event);
conf_event.edge_detect = EVENTS_EDGE_DETECT_NONE;
conf_event.path = EVENTS_PATH_ASYNCHRONOUS;
conf_event.generator = EVSYS_ID_GEN_TC0_MCX_0;
events_allocate(&conf_event_resource, &conf_event);
events_attach_user(&conf_event_resource, EVSYS_ID_USER_DAC_START);
}
/* Initialize the selected waveform buffer with output data */
void buffer_init(void)
{
#if WAVE_MODE==SINE_WAVE
for (i = 0; i < DEGREES_PER_CYCLE; i++) {
sine_wave_buf[i] = (uint16_t)(500 + (500*sin((double)i*DEGREE)));
}
#elif WAVE_MODE==SAW_TOOTH_WAVE
for (i = 0; i < 256; i++) {
sawtooth_wave_buf[i] = i*4;
}
#elif WAVE_MODE==TRIANGLE_WAVE
for (i = 0; i < 128; i++) {
triangle_wave_buf[i] = i*8;
}
for (i = 128; i < 256; i++) {
triangle_wave_buf[i] = 1023 - (i*8);
}
#endif
}
/* Main function */
int main(void)
{
system_init();
timer_init();
dac_initialize();
evsys_init();
buffer_init();
/* Set the TC0 compare value corresponding to specified frequency */
#if WAVE_MODE==SINE_WAVE
tc_set_compare_value(&tc_inst, 0, \
system_gclk_gen_get_hz(GCLK_GENERATOR_0)/(FREQUENCY*360));
#else
tc_set_compare_value(&tc_inst, 0, \
system_gclk_gen_get_hz(GCLK_GENERATOR_0)/(FREQUENCY*256));
#endif
/* Start TC0 timer */
tc_start_counter(&tc_inst);
/* Enable global interrupt */
system_interrupt_enable_global();
while (true) {
}
}
