/*---------------------------------------------------------------------------*/
void
lpm_drop()
{
lpm_registered_module_t *module;
uint8_t max_pm = LPM_MODE_MAX_SUPPORTED;
uint8_t module_pm;
clock_time_t next_event;
uint32_t domains = LOCKABLE_DOMAINS;
if(RTIMER_CLOCK_LT(soc_rtc_get_next_trigger(),
RTIMER_NOW() + STANDBY_MIN_DURATION)) {
lpm_sleep();
return;
}
/* Collect max allowed PM permission from interested modules */
for(module = list_head(modules_list); module != NULL;
module = module->next) {
if(module->request_max_pm) {
module_pm = module->request_max_pm();
if(module_pm < max_pm) {
max_pm = module_pm;
}
}
}
/* Check if any events fired during this process. Last chance to abort */
if(process_nevents()) {
return;
}
/* Drop */
if(max_pm == LPM_MODE_SLEEP) {
lpm_sleep();
} else {
/* Critical. Don't get interrupted! */
ti_lib_int_master_disable();
/*
* Reschedule AON RTC CH1 to fire an event N ticks before the next etimer
* event
*/
next_event = etimer_next_expiration_time();
if(next_event) {
next_event = next_event - clock_time();
soc_rtc_schedule_one_shot(AON_RTC_CH1, RTIMER_NOW() +
(next_event * (RTIMER_SECOND / CLOCK_SECOND)));
}
/*
* Notify all registered modules that we are dropping to mode X. We do not
* need to do this for simple sleep.
*
* This is a chance for modules to delay us a little bit until an ongoing
* operation has finished (e.g. uart TX) or to configure themselves for
* deep sleep.
*
* At this stage, we also collect power domain locks, if any.
* The argument to PRCMPowerDomainOff() is a bitwise OR, so every time
* we encounter a lock we just clear the respective bits in the 'domains'
* variable as required by the lock. In the end the domains variable will
* just hold whatever has not been cleared
*/
for(module = list_head(modules_list); module != NULL;
module = module->next) {
if(module->shutdown) {
module->shutdown(max_pm);
}
/* Clear the bits specified in the lock */
domains &= ~module->domain_lock;
}
/* Pat the dog: We don't want it to shout right after we wake up */
watchdog_periodic();
/* Clear unacceptable bits, just in case a lock provided a bad value */
domains &= LOCKABLE_DOMAINS;
/*
* Freeze the IOs on the boundary between MCU and AON. We only do this if
* PERIPH is not needed
*/
if(domains & PRCM_DOMAIN_PERIPH) {
ti_lib_aon_ioc_freeze_enable();
}
/*
* Among LOCKABLE_DOMAINS, turn off those that are not locked
*
* If domains is != 0, pass it as-is
*/
if(domains) {
ti_lib_prcm_power_domain_off(domains);
}
/*
* Before entering Deep Sleep, we must switch off the HF XOSC. The HF XOSC
* is predominantly controlled by the RF driver. In a build with radio
* cycling (e.g. ContikiMAC), the RF driver will request the XOSC before
* using the Freq. Synth, and switch back to the RC when it is about to
* turn back off.
*
* If the radio is on, we won't even reach here, and if it's off the HF
* clock source should already be the HF RC.
*
* Nevertheless, request the switch to the HF RC explicitly here.
*/
oscillators_switch_to_hf_rc();
/* Configure clock sources for MCU and AUX: No clock */
ti_lib_aon_wuc_mcu_power_down_config(AONWUC_NO_CLOCK);
ti_lib_aon_wuc_aux_power_down_config(AONWUC_NO_CLOCK);
/* Full RAM retention. */
ti_lib_aon_wuc_mcu_sram_config(MCU_RAM0_RETENTION | MCU_RAM1_RETENTION |
MCU_RAM2_RETENTION | MCU_RAM3_RETENTION);
/* Disable retention of AUX RAM */
ti_lib_aon_wuc_aux_sram_config(false);
/*
* Always turn off RFCORE, CPU, SYSBUS and VIMS. RFCORE should be off
* already
*/
ti_lib_prcm_power_domain_off(PRCM_DOMAIN_RFCORE | PRCM_DOMAIN_CPU |
PRCM_DOMAIN_VIMS | PRCM_DOMAIN_SYSBUS);
/* Request JTAG domain power off */
ti_lib_aon_wuc_jtag_power_off();
/* Turn off AUX */
ti_lib_aux_wuc_power_ctrl(AUX_WUC_POWER_OFF);
ti_lib_aon_wuc_domain_power_down_enable();
while(ti_lib_aon_wuc_power_status_get() & AONWUC_AUX_POWER_ON);
/* Configure the recharge controller */
ti_lib_sys_ctrl_set_recharge_before_power_down(XOSC_IN_HIGH_POWER_MODE);
/*
* If both PERIPH and SERIAL PDs are off, request the uLDO as the power
* source while in deep sleep.
*/
if(domains == LOCKABLE_DOMAINS) {
ti_lib_pwr_ctrl_source_set(PWRCTRL_PWRSRC_ULDO);
}
/* We are only interested in IRQ energest while idle or in LPM */
ENERGEST_IRQ_RESTORE(irq_energest);
ENERGEST_SWITCH(ENERGEST_TYPE_CPU, ENERGEST_TYPE_LPM);
/* Sync the AON interface to ensure all writes have gone through. */
ti_lib_sys_ctrl_aon_sync();
/*
* Explicitly turn off VIMS cache, CRAM and TRAM. Needed because of
* retention mismatch between VIMS logic and cache. We wait to do this
* until right before deep sleep to be able to use the cache for as long
* as possible.
*/
ti_lib_prcm_cache_retention_disable();
ti_lib_vims_mode_set(VIMS_BASE, VIMS_MODE_OFF);
/* Deep Sleep */
ti_lib_prcm_deep_sleep();
/*
* When we reach here, some interrupt woke us up. The global interrupt
* flag is off, hence we have a chance to run things here. We will wake up
* the chip properly, and then we will enable the global interrupt without
* unpending events so the handlers can fire
*/
wake_up();
ti_lib_int_master_enable();
}
}
/**
* \brief Main function for CC26xx-based platforms
*
* The same main() is used for both Srf+CC26xxEM as well as for the SensorTag
*/
int
main(void)
{
/* Set the LF XOSC as the LF system clock source */
select_lf_xosc();
/*
* Make sure to open the latches - this will be important when returning
* from shutdown
*/
ti_lib_pwr_ctrl_io_freeze_disable();
/* Use DCDC instead of LDO to save current */
ti_lib_pwr_ctrl_source_set(PWRCTRL_PWRSRC_DCDC);
lpm_init();
board_init();
/* Enable flash cache and prefetch. */
ti_lib_vims_mode_set(VIMS_BASE, VIMS_MODE_ENABLED);
ti_lib_vims_configure(VIMS_BASE, true, true);
gpio_interrupt_init();
/* Clock must always be enabled for the semaphore module */
HWREG(AUX_WUC_BASE + AUX_WUC_O_MODCLKEN1) = AUX_WUC_MODCLKEN1_SMPH;
leds_init();
fade(LEDS_RED);
cc26xx_rtc_init();
clock_init();
rtimer_init();
watchdog_init();
process_init();
random_init(0x1234);
/* Character I/O Initialisation */
#if CC26XX_UART_CONF_ENABLE
cc26xx_uart_init();
cc26xx_uart_set_input(serial_line_input_byte);
#endif
serial_line_init();
printf("Starting " CONTIKI_VERSION_STRING "\n");
printf("With DriverLib v%u.%02u.%02u.%u\n", DRIVERLIB_MAJOR_VER,
DRIVERLIB_MINOR_VER, DRIVERLIB_PATCH_VER, DRIVERLIB_BUILD_ID);
printf(BOARD_STRING " using CC%u\n", CC26XX_MODEL_CPU_VARIANT);
process_start(&etimer_process, NULL);
ctimer_init();
energest_init();
ENERGEST_ON(ENERGEST_TYPE_CPU);
fade(LEDS_YELLOW);
printf(" Net: ");
printf("%s\n", NETSTACK_NETWORK.name);
printf(" MAC: ");
printf("%s\n", NETSTACK_MAC.name);
printf(" RDC: ");
printf("%s", NETSTACK_RDC.name);
if(NETSTACK_RDC.channel_check_interval() != 0) {
printf(", Channel Check Interval: %u ticks",
NETSTACK_RDC.channel_check_interval());
}
printf("\n");
netstack_init();
set_rf_params();
#if NETSTACK_CONF_WITH_IPV6
memcpy(&uip_lladdr.addr, &linkaddr_node_addr, sizeof(uip_lladdr.addr));
queuebuf_init();
process_start(&tcpip_process, NULL);
#endif /* NETSTACK_CONF_WITH_IPV6 */
fade(LEDS_GREEN);
process_start(&sensors_process, NULL);
autostart_start(autostart_processes);
watchdog_start();
fade(LEDS_ORANGE);
while(1) {
uint8_t r;
do {
r = process_run();
watchdog_periodic();
} while(r > 0);
/* Drop to some low power mode */
lpm_drop();
}
}
