int main (void) {
int32_t cycles = 3;
pllstart_seventytwomhz() ;
// pllstart_sixtymhz() ;
//pllstart_fourtyeightmhz() ;
uart0_init_115200() ;
vic_enableIRQ();
vic_enableFIQ();
uart0_putstring("\n***Starting i2c two device test (olimex2378)***\n\n");
i2c_init(I2C0);
// strange duty cycle just for fun.
i2c_freq(I2C0, (uint16_t) 90, (uint16_t) 180);
stat_led_flash_fast(cycles); // initial visual check
eeprom_task() ;
blinkm_task_i2c0() ;
// stat_led_flash_fast(4);
uart0_putstring("\n\n***Done***\n\n");
return(0);
}
/*
* main
*/
int main(void) {
FIO_ENABLE;
pllstart_seventytwomhz() ;
mam_enable();
uart0_init_115200() ;
DBG(UART0,"Initialising USB stack\n");
// initialise stack
USBInit();
// register descriptors
USBRegisterDescriptors(abDescriptors);
// register class request handler
USBRegisterRequestHandler(REQTYPE_TYPE_CLASS, HandleClassRequest, abClassReqData);
// register endpoint handlers
USBHwRegisterEPIntHandler(INT_IN_EP, NULL);
// register frame handler
USBHwRegisterFrameHandler(USBFrameHandler);
// register device event handler
USBHwRegisterDevIntHandler(USBDevIntHandler);
inputIsocDataBuffer[0] = 0;
DBG(UART0,"Starting USB isoc datatpath test\n");
VICVectPriority22 = 0x01;
VICVectAddr22 = (int) USBIntHandler;
// set up USB interrupt
VICIntSelect &= ~(1<<22); // select IRQ for USB
VICIntEnable |= (1<<22);
vic_enableIRQ();
// connect to bus
USBHwConnect(TRUE);
stream_task();
return 0;
}
/*************************************************************************
main
====
**************************************************************************/
int main(void)
{
int x = 0;
const int interval = 200000;
FIO_ENABLE;
vic_disableIRQ();
pllstart_seventytwomhz() ;
// pllstart_sixtymhz() ;
// pllstart_fourtyeightmhz() ;
mam_enable();
info_init();
uart0_init_115200() ;
uart0_putstring("\n***Starting gfe color led test***\n\n");
uart0_putstring("\n***Board is defined as: ");
uart0_putstring( infoquery_gfe_boardtag() );
uart0_putstring(" ***\n");
init_color_led();
RED_LED_OFF;
BLUE_LED_OFF;
GREEN_LED_OFF;
printf_lpc(UART0,"5 FAST flashes...red, blue then green\n");
color_led_flash(5, RED_LED, FLASH_FAST ) ;
RED_LED_OFF;
color_led_flash(5, BLUE_LED, FLASH_FAST ) ;
BLUE_LED_OFF;
color_led_flash(5, GREEN_LED, FLASH_FAST ) ;
GREEN_LED_OFF;
uart0_putstring(" ** END OF TEST ""\n");
printf_lpc(UART0, "Initialising USB stack\n");
// initialize stack
USBInit();
// register descriptors
USBRegisterDescriptors(abDescriptors);
// register class request handler
USBRegisterRequestHandler(REQTYPE_TYPE_CLASS, HandleClassRequest, abClassReqData);
// register endpoint handlers
USBHwRegisterEPIntHandler(INT_IN_EP, NULL);
// register frame handler
USBHwRegisterFrameHandler(USBFrameHandler);
// register device event handler
USBHwRegisterDevIntHandler(USBDevIntHandler);
inputIsocDataBuffer[0] = 0;
printf_lpc(UART0, "Starting USB communication\n");
VICVectPriority22 = 0x01; // 0x0 is highest priority, 0xF is lowest
VICVectAddr22 = (unsigned int)USBIntHandler;
VICAddress = 0x0;
printf_lpc(UART0, "addresses entered\n");
ENABLE_USB_IRQ;
printf_lpc(UART0, "USB IRQ Enabled\n");
vic_enableIRQ();
printf_lpc(UART0, "vic_enable\n");
ENABLE_USB_INT;
printf_lpc(UART0, "USB INT Enabled\n");
//printf_lpc(UART0, "connect to bus\n");
//
// // connect to bus
USBHwConnect(TRUE);
//
for(;;) {
x++;
if (x == interval) {
RED_LED_ON;
} else if (x >= (interval*2)) {
x = 0;
RED_LED_OFF;
}
}
return 0;
}
/*! \brief turn interrupts on at the CPU status register
*
*/
void vic_cpu_enable_interrupts() {
vic_enableIRQ();
vic_enableFIQ();
}
