enum power_state power_chipset_init(void)
{
/*
* If we're switching between images without rebooting, see if the x86
* is already powered on; if so, leave it there instead of cycling
* through G3.
*/
if (system_jumped_to_this_image()) {
if ((power_get_signals() & IN_ALL_S0) == IN_ALL_S0) {
/* Disable idle task deep sleep when in S0. */
disable_sleep(SLEEP_MASK_AP_RUN);
CPRINTS("already in S0");
return POWER_S0;
} else {
/* Force all signals to their G3 states */
CPRINTS("forcing G3");
gpio_set_level(GPIO_PCH_PWROK, 0);
gpio_set_level(GPIO_SYS_PWROK, 0);
gpio_set_level(GPIO_PP1050_EN, 0);
gpio_set_level(GPIO_PP1200_EN, 0);
gpio_set_level(GPIO_PP1800_EN, 0);
gpio_set_level(GPIO_PP3300_DSW_GATED_EN, 0);
gpio_set_level(GPIO_PP5000_USB_EN, 0);
gpio_set_level(GPIO_PP5000_EN, 0);
gpio_set_level(GPIO_PCH_DPWROK, 0);
gpio_set_level(GPIO_PP3300_DSW_EN, 0);
wireless_set_state(WIRELESS_OFF);
}
}
return POWER_G3;
}
enum power_state power_handle_state(enum power_state state)
{
/*
* Pass through RSMRST asynchronously, as PCH may not react
* immediately to power changes.
*/
int rsmrst_in = gpio_get_level(GPIO_RSMRST_L_PGOOD);
int rsmrst_out = gpio_get_level(GPIO_PCH_RSMRST_L);
#ifdef GLADOS_BOARD_V2
int tries = 0;
#endif
if (rsmrst_in != rsmrst_out) {
/*
* Wait at least 10ms between power signals going high
* and deasserting RSMRST to PCH.
*/
if (rsmrst_in)
msleep(10);
gpio_set_level(GPIO_PCH_RSMRST_L, rsmrst_in);
CPRINTS("RSMRST: %d", rsmrst_in);
}
switch (state) {
case POWER_G3:
if (forcing_shutdown) {
power_button_pch_release();
forcing_shutdown = 0;
}
break;
case POWER_S5:
if (gpio_get_level(GPIO_PCH_SLP_S4_L) == 1)
return POWER_S5S3; /* Power up to next state */
break;
case POWER_S3:
if (!power_has_signals(IN_PGOOD_ALL_CORE)) {
/* Required rail went away */
chipset_force_shutdown();
return POWER_S3S5;
} else if (gpio_get_level(GPIO_PCH_SLP_S3_L) == 1) {
/* Power up to next state */
return POWER_S3S0;
} else if (gpio_get_level(GPIO_PCH_SLP_S4_L) == 0) {
/* Power down to next state */
return POWER_S3S5;
}
break;
case POWER_S0:
if (!power_has_signals(IN_PGOOD_ALL_CORE)) {
chipset_force_shutdown();
return POWER_S0S3;
} else if (gpio_get_level(GPIO_PCH_SLP_S3_L) == 0) {
/* Power down to next state */
return POWER_S0S3;
}
break;
case POWER_G3S5:
/* Call hooks to initialize PMIC */
hook_notify(HOOK_CHIPSET_PRE_INIT);
if (power_wait_signals(IN_PCH_SLP_SUS_DEASSERTED)) {
chipset_force_shutdown();
return POWER_G3;
}
#ifdef GLADOS_BOARD_V2
/*
* Allow up to 1s for charger to be initialized, in case
* we're trying to boot the AP with no battery.
*/
while (charge_prevent_power_on() &&
tries++ < CHARGER_INITIALIZED_TRIES) {
msleep(CHARGER_INITIALIZED_DELAY_MS);
}
/* Return to G3 if battery level is too low */
if (charge_want_shutdown() ||
tries == CHARGER_INITIALIZED_TRIES) {
CPRINTS("power-up inhibited");
chipset_force_shutdown();
return POWER_G3;
}
/* Allow AP to power on */
gpio_set_level(GPIO_PMIC_SLP_SUS_L, 1);
gpio_set_level(GPIO_PCH_BATLOW_L, 1);
#endif
return POWER_S5;
case POWER_S5S3:
if (!power_has_signals(IN_PGOOD_ALL_CORE)) {
/* Required rail went away */
chipset_force_shutdown();
return POWER_S5G3;
}
/* Enable TP + USB so that they can wake the system */
gpio_set_level(GPIO_ENABLE_TOUCHPAD, 1);
gpio_set_level(GPIO_USB1_ENABLE, 1);
gpio_set_level(GPIO_USB2_ENABLE, 1);
/* Call hooks now that rails are up */
hook_notify(HOOK_CHIPSET_STARTUP);
return POWER_S3;
case POWER_S3S0:
if (!power_has_signals(IN_PGOOD_ALL_CORE)) {
/* Required rail went away */
chipset_force_shutdown();
return POWER_S3S5;
}
gpio_set_level(GPIO_ENABLE_BACKLIGHT, 1);
/* Enable wireless */
wireless_set_state(WIRELESS_ON);
/* Call hooks now that rails are up */
hook_notify(HOOK_CHIPSET_RESUME);
/*
* Disable idle task deep sleep. This means that the low
* power idle task will not go into deep sleep while in S0.
*/
disable_sleep(SLEEP_MASK_AP_RUN);
/*
* Throttle CPU if necessary. This should only be asserted
* when +VCCP is powered (it is by now).
*/
gpio_set_level(GPIO_CPU_PROCHOT, throttle_cpu);
return POWER_S0;
case POWER_S0S3:
/* Call hooks before we remove power rails */
hook_notify(HOOK_CHIPSET_SUSPEND);
gpio_set_level(GPIO_ENABLE_BACKLIGHT, 0);
/* Suspend wireless */
wireless_set_state(WIRELESS_SUSPEND);
/*
* Enable idle task deep sleep. Allow the low power idle task
* to go into deep sleep in S3 or lower.
*/
enable_sleep(SLEEP_MASK_AP_RUN);
return POWER_S3;
case POWER_S3S5:
/* Call hooks before we remove power rails */
hook_notify(HOOK_CHIPSET_SHUTDOWN);
/* Disable wireless */
wireless_set_state(WIRELESS_OFF);
gpio_set_level(GPIO_ENABLE_TOUCHPAD, 0);
gpio_set_level(GPIO_USB1_ENABLE, 0);
gpio_set_level(GPIO_USB2_ENABLE, 0);
return POWER_S5G3;
case POWER_S5G3:
#ifdef CONFIG_G3_SLEEP
gpio_set_level(GPIO_G3_SLEEP_EN, 1);
#endif
chipset_force_g3();
return POWER_G3;
default:
break;
}
return state;
}
static enum power_state _power_handle_state(enum power_state state)
{
int tries = 0;
switch (state) {
case POWER_G3:
break;
case POWER_S5:
if (forcing_shutdown) {
power_button_pch_release();
forcing_shutdown = 0;
}
#ifdef CONFIG_BOARD_HAS_RTC_RESET
/* Wait for S5 exit and attempt RTC reset it supported */
if (power_s5_up)
return power_wait_s5_rtc_reset();
#endif
if (gpio_get_level(GPIO_PCH_SLP_S4_L) == 1)
return POWER_S5S3; /* Power up to next state */
break;
case POWER_S3:
if (!power_has_signals(IN_PGOOD_ALL_CORE)) {
/* Required rail went away */
chipset_force_shutdown();
return POWER_S3S5;
} else if (gpio_get_level(GPIO_PCH_SLP_S3_L) == 1) {
/* Power up to next state */
return POWER_S3S0;
} else if (gpio_get_level(GPIO_PCH_SLP_S4_L) == 0) {
/* Power down to next state */
return POWER_S3S5;
}
break;
case POWER_S0:
if (!power_has_signals(IN_PGOOD_ALL_CORE)) {
chipset_force_shutdown();
return POWER_S0S3;
#ifdef CONFIG_POWER_S0IX
} else if ((gpio_get_level(GPIO_PCH_SLP_S0_L) == 0) &&
(gpio_get_level(GPIO_PCH_SLP_S3_L) == 1)) {
return POWER_S0S0ix;
#endif
} else if (gpio_get_level(GPIO_PCH_SLP_S3_L) == 0) {
/* Power down to next state */
return POWER_S0S3;
}
break;
#ifdef CONFIG_POWER_S0IX
case POWER_S0ix:
/*
* TODO: add code for unexpected power loss
*/
if ((gpio_get_level(GPIO_PCH_SLP_S0_L) == 1) &&
(gpio_get_level(GPIO_PCH_SLP_S3_L) == 1)) {
return POWER_S0ixS0;
}
break;
#endif
case POWER_G3S5:
/* Call hooks to initialize PMIC */
hook_notify(HOOK_CHIPSET_PRE_INIT);
/*
* Allow up to 1s for charger to be initialized, in case
* we're trying to boot the AP with no battery.
*/
while (charge_prevent_power_on(0) &&
tries++ < CHARGER_INITIALIZED_TRIES) {
msleep(CHARGER_INITIALIZED_DELAY_MS);
}
/* Return to G3 if battery level is too low */
if (charge_want_shutdown() ||
tries > CHARGER_INITIALIZED_TRIES) {
CPRINTS("power-up inhibited");
chipset_force_shutdown();
return POWER_G3;
}
if (power_wait_signals(IN_PCH_SLP_SUS_DEASSERTED)) {
chipset_force_shutdown();
return POWER_G3;
}
power_s5_up = 1;
return POWER_S5;
case POWER_S5S3:
if (!power_has_signals(IN_PGOOD_ALL_CORE)) {
/* Required rail went away */
chipset_force_shutdown();
return POWER_S5G3;
}
/* Call hooks now that rails are up */
hook_notify(HOOK_CHIPSET_STARTUP);
return POWER_S3;
case POWER_S3S0:
if (!power_has_signals(IN_PGOOD_ALL_CORE)) {
/* Required rail went away */
chipset_force_shutdown();
return POWER_S3S5;
}
gpio_set_level(GPIO_ENABLE_BACKLIGHT, 1);
/* Enable wireless */
wireless_set_state(WIRELESS_ON);
/* Call hooks now that rails are up */
hook_notify(HOOK_CHIPSET_RESUME);
/*
* Disable idle task deep sleep. This means that the low
* power idle task will not go into deep sleep while in S0.
*/
disable_sleep(SLEEP_MASK_AP_RUN);
/*
* Throttle CPU if necessary. This should only be asserted
* when +VCCP is powered (it is by now).
*/
gpio_set_level(GPIO_CPU_PROCHOT, throttle_cpu);
return POWER_S0;
case POWER_S0S3:
/* Call hooks before we remove power rails */
hook_notify(HOOK_CHIPSET_SUSPEND);
gpio_set_level(GPIO_ENABLE_BACKLIGHT, 0);
/* Suspend wireless */
wireless_set_state(WIRELESS_SUSPEND);
/*
* Enable idle task deep sleep. Allow the low power idle task
* to go into deep sleep in S3 or lower.
*/
enable_sleep(SLEEP_MASK_AP_RUN);
return POWER_S3;
#ifdef CONFIG_POWER_S0IX
case POWER_S0S0ix:
/* call hooks before standby */
hook_notify(HOOK_CHIPSET_SUSPEND);
lpc_enable_wake_mask_for_lid_open();
/*
* Enable idle task deep sleep. Allow the low power idle task
* to go into deep sleep in S0ix.
*/
enable_sleep(SLEEP_MASK_AP_RUN);
return POWER_S0ix;
case POWER_S0ixS0:
lpc_disable_wake_mask_for_lid_open();
/* Call hooks now that rails are up */
hook_notify(HOOK_CHIPSET_RESUME);
/*
* Disable idle task deep sleep. This means that the low
* power idle task will not go into deep sleep while in S0.
*/
disable_sleep(SLEEP_MASK_AP_RUN);
return POWER_S0;
#endif
case POWER_S3S5:
/* Call hooks before we remove power rails */
hook_notify(HOOK_CHIPSET_SHUTDOWN);
/* Disable wireless */
wireless_set_state(WIRELESS_OFF);
/* Always enter into S5 state. The S5 state is required to
* correctly handle global resets which have a bit of delay
* while the SLP_Sx_L signals are asserted then deasserted. */
power_s5_up = 0;
return POWER_S5;
case POWER_S5G3:
chipset_force_g3();
return POWER_G3;
default:
break;
}
return state;
}
enum power_state power_handle_state(enum power_state state)
{
switch (state) {
case POWER_G3:
break;
case POWER_S5:
if (gpio_get_level(GPIO_PCH_SLP_S5_L) == 1)
return POWER_S5S3; /* Power up to next state */
break;
case POWER_S3:
/* Check for state transitions */
if (!power_has_signals(IN_PGOOD_S3)) {
/* Required rail went away */
chipset_force_shutdown();
return POWER_S3S5;
} else if (gpio_get_level(GPIO_PCH_SLP_S3_L) == 1) {
/* Power up to next state */
return POWER_S3S0;
} else if (gpio_get_level(GPIO_PCH_SLP_S5_L) == 0) {
/* Power down to next state */
return POWER_S3S5;
}
break;
case POWER_S0:
if (!power_has_signals(IN_PGOOD_S0)) {
/* Required rail went away */
chipset_force_shutdown();
return POWER_S0S3;
} else if (gpio_get_level(GPIO_PCH_SLP_S3_L) == 0) {
/* Power down to next state */
return POWER_S0S3;
}
break;
case POWER_G3S5:
/* Enable 3.3V DSW */
gpio_set_level(GPIO_PP3300_DSW_EN, 1);
/*
* Wait 10ms after +3VALW good, since that powers VccDSW and
* VccSUS.
*/
msleep(10);
/* Enable PP5000 (5V) rail as 1.05V and 1.2V rails need 5V
* rail to regulate properly. */
gpio_set_level(GPIO_PP5000_EN, 1);
/* Wait for PP1050/PP1200 PGOOD to go LOW to
* indicate that PP5000 is stable */
while ((power_get_signals() & IN_PGOOD_PP5000) != 0) {
if (task_wait_event(SECOND) == TASK_EVENT_TIMER) {
CPRINTS("timeout waiting for PP5000");
gpio_set_level(GPIO_PP5000_EN, 0);
chipset_force_shutdown();
return POWER_G3;
}
}
/* Turn on 3.3V DSW gated rail for core regulator */
gpio_set_level(GPIO_PP3300_DSW_GATED_EN, 1);
/* Assert DPWROK */
gpio_set_level(GPIO_PCH_DPWROK, 1);
/* Enable PP1050 rail. */
gpio_set_level(GPIO_PP1050_EN, 1);
/* Wait for 1.05V to come up and CPU to notice */
if (power_wait_signals(IN_PGOOD_PP1050 |
IN_PCH_SLP_SUS_DEASSERTED)) {
gpio_set_level(GPIO_PP1050_EN, 0);
gpio_set_level(GPIO_PP3300_DSW_GATED_EN, 0);
gpio_set_level(GPIO_PP5000_EN, 0);
chipset_force_shutdown();
return POWER_G3;
}
/* Wait 5ms for SUSCLK to stabilize */
msleep(5);
/* Call hook to indicate out of G3 state */
hook_notify(HOOK_CHIPSET_PRE_INIT);
return POWER_S5;
case POWER_S5S3:
/* Turn on power to RAM */
gpio_set_level(GPIO_PP1800_EN, 1);
gpio_set_level(GPIO_PP1200_EN, 1);
if (power_wait_signals(IN_PGOOD_S3)) {
gpio_set_level(GPIO_PP1800_EN, 0);
gpio_set_level(GPIO_PP1200_EN, 0);
chipset_force_shutdown();
return POWER_S5;
}
/*
* Take lightbar out of reset, now that +5VALW is
* available and we won't leak +3VALW through the reset
* line.
*/
gpio_set_level(GPIO_LIGHTBAR_RESET_L, 1);
/*
* Enable touchpad power so it can wake the system from
* suspend.
*/
gpio_set_level(GPIO_ENABLE_TOUCHPAD, 1);
/* Turn on USB power rail. */
gpio_set_level(GPIO_PP5000_USB_EN, 1);
/* Call hooks now that rails are up */
hook_notify(HOOK_CHIPSET_STARTUP);
return POWER_S3;
case POWER_S3S0:
/* Wait 20ms before allowing VCCST_PGOOD to rise. */
msleep(20);
/* Enable wireless. */
wireless_set_state(WIRELESS_ON);
/* Make sure the touchscreen is on, too. */
gpio_set_level(GPIO_TOUCHSCREEN_RESET_L, 1);
/* Wait for non-core power rails good */
if (power_wait_signals(IN_PGOOD_S0)) {
chipset_force_shutdown();
wireless_set_state(WIRELESS_OFF);
return POWER_S3;
}
/* Call hooks now that rails are up */
hook_notify(HOOK_CHIPSET_RESUME);
/*
* Disable idle task deep sleep. This means that the low
* power idle task will not go into deep sleep while in S0.
*/
disable_sleep(SLEEP_MASK_AP_RUN);
/* Wait 99ms after all voltages good */
msleep(99);
/*
* Throttle CPU if necessary. This should only be asserted
* when +VCCP is powered (it is by now).
*/
gpio_set_level(GPIO_CPU_PROCHOT, throttle_cpu);
/* Set PCH_PWROK */
gpio_set_level(GPIO_PCH_PWROK, 1);
gpio_set_level(GPIO_SYS_PWROK, 1);
return POWER_S0;
case POWER_S0S3:
/* Call hooks before we remove power rails */
hook_notify(HOOK_CHIPSET_SUSPEND);
/* Clear PCH_PWROK */
gpio_set_level(GPIO_SYS_PWROK, 0);
gpio_set_level(GPIO_PCH_PWROK, 0);
/* Wait 40ns */
udelay(1);
/* Suspend wireless */
wireless_set_state(WIRELESS_SUSPEND);
/*
* Enable idle task deep sleep. Allow the low power idle task
* to go into deep sleep in S3 or lower.
*/
enable_sleep(SLEEP_MASK_AP_RUN);
/*
* Deassert prochot since CPU is off and we're about to drop
* +VCCP.
*/
gpio_set_level(GPIO_CPU_PROCHOT, 0);
return POWER_S3;
case POWER_S3S5:
/* Call hooks before we remove power rails */
hook_notify(HOOK_CHIPSET_SHUTDOWN);
/* Disable wireless */
wireless_set_state(WIRELESS_OFF);
/* Disable peripheral power */
gpio_set_level(GPIO_ENABLE_TOUCHPAD, 0);
gpio_set_level(GPIO_PP5000_USB_EN, 0);
/* Turn off power to RAM */
gpio_set_level(GPIO_PP1800_EN, 0);
gpio_set_level(GPIO_PP1200_EN, 0);
/*
* Put touchscreen and lightbar in reset, so we won't
* leak +3VALW through the reset line to chips powered
* by +5VALW.
*
* (Note that we're no longer powering down +5VALW due
* to crosbug.com/p/16600, but to minimize side effects
* of that change we'll still reset these components in
* S5.)
*/
gpio_set_level(GPIO_TOUCHSCREEN_RESET_L, 0);
gpio_set_level(GPIO_LIGHTBAR_RESET_L, 0);
return pause_in_s5 ? POWER_S5 : POWER_S5G3;
case POWER_S5G3:
/* Deassert DPWROK */
gpio_set_level(GPIO_PCH_DPWROK, 0);
/* Turn off power rails enabled in S5 */
gpio_set_level(GPIO_PP1050_EN, 0);
gpio_set_level(GPIO_PP3300_DSW_GATED_EN, 0);
gpio_set_level(GPIO_PP5000_EN, 0);
/* Disable 3.3V DSW */
gpio_set_level(GPIO_PP3300_DSW_EN, 0);
return POWER_G3;
}
return state;
}
