static void AppThread(void *arg) {
chRegSetThreadName("App");
uint32_t EvtMsk;
bool PillConnected = false;
while(true) {
EvtMsk = chEvtWaitAny(ALL_EVENTS);
// ==== Process dose ====
// if(EvtMsk & EVTMSK_DOSE_INC) {
// // Check if radio damage occured. Will return 1 if no.
// uint32_t FDamage = Radio.Damage;
// //if(FDamage != 1) Uart.Printf("Dmg=%u\r", FDamage);
// Dose.Increase(FDamage, diUsual);
// //Uart.Printf("Dz=%u; Dmg=%u\r", Dose.Get(), FDamage);
// }
// ==== Store dose ====
// if(EvtMsk & EVTMSK_DOSE_STORE) {
// //if(Dose.Save() != OK) Uart.Printf("EE Fail\r"); // DEBUG
// }
// ==== Check pill ====
if(EvtMsk & EVTMSK_PILL_CHECK) {
// Check if new connection occured
if(PillMgr.CheckIfConnected(PILL_I2C_ADDR) == OK) {
if(!PillConnected) {
PillConnected = true;
App.IPillHandler();
}
}
else PillConnected = false;
} // if EVTMSK_PILL_CHECK
} // while 1
}
int main() {
// ==== Setup clock ====
Clk.UpdateFreqValues();
uint8_t ClkResult = FAILURE;
Clk.SetupFlashLatency(12); // Setup Flash Latency for clock in MHz
// 12 MHz/6 = 2; 2*192 = 384; 384/8 = 48 (preAHB divider); 384/8 = 48 (USB clock)
Clk.SetupPLLDividers(6, 192, pllSysDiv8, 8);
// 48/4 = 12 MHz core clock. APB1 & APB2 clock derive on AHB clock
Clk.SetupBusDividers(ahbDiv4, apbDiv1, apbDiv1);
if((ClkResult = Clk.SwitchToPLL()) == 0) Clk.HSIDisable();
Clk.UpdateFreqValues();
// ==== Init OS ====
halInit();
chSysInit();
// ==== Init Hard & Soft ====
App.PThd = chThdSelf();
Uart.Init(115200);
Uart.Printf("\rLockNFC3 F205 AHB freq=%uMHz", Clk.AHBFreqHz/1000000);
// Report problem with clock if any
if(ClkResult) Uart.Printf("Clock failure\r");
LedService.Init();
LedService.StartSequence(lsqBlinkGreenX2);
Led.Init();
Led.StartSequence(lsqDoorClose);
Sensors.Init();
Pn.Init();
SD.Init(); // SD-card init
App.IDStore.Load(); // Init Srorage of IDs
SndList.Init();
App.ReadConfig(); // Read config from SD-card
Sound.Init();
Sound.SetVolume(250);
Sound.RegisterAppThd(chThdSelf());
Sound.Play("alive.wav");
#if USB_ENABLED
MassStorage.Init(); // Init USB MassStorage device
#endif
// ==== Main cycle ====
App.ITask();
}
int main(void) {
// ==== Setup clock frequency ====
uint8_t ClkResult = 1;
Clk.SetupFlashLatency(64); // Setup Flash Latency for clock in MHz
Clk.EnablePrefetch();
// 12 MHz/6 = 2; 2*192 = 384; 384/6 = 64 (preAHB divider); 384/8 = 48 (USB clock)
Clk.SetupPLLDividers(6, 192, pllSysDiv6, 8);
// 64/1 = 64 MHz core clock. APB1 & APB2 clock derive on AHB clock; APB1max = 42MHz, APB2max = 84MHz
// Keep APB freq at 32 MHz to left peripheral settings untouched
Clk.SetupBusDividers(ahbDiv1, apbDiv2, apbDiv2);
if((ClkResult = Clk.SwitchToPLL()) == 0) Clk.HSIDisable();
Clk.UpdateFreqValues();
// Init OS
halInit();
chSysInit();
// ==== Init hardware ====
Uart.Init(115200, UART_GPIO, UART_TX_PIN, UART_GPIO, UART_RX_PIN);
Uart.Printf("\r%S %S", APP_NAME, APP_VERSION);
Clk.PrintFreqs();
if(ClkResult != 0) Uart.Printf("\rXTAL failure");
App.InitThread();
// Leds
LedAux.Init();
for(uint8_t i=0; i<4; i++) {
Led[i].Init();
// for(uint8_t j=0; j<250; j++) {
// Led[i].Set(j);
// chThdSleepMilliseconds(4);
// }
// Led[i].Set(0);
}
// Debug: init CS2 as output
PinSetupOut(GPIOC, 13, omPushPull, pudNone);
// ==== USB ====
UsbAu.Init();
UsbAu.Connect();
Pcm.Init();
// Main cycle
App.ITask();
}
int main(void) {
// ==== Init Vcore & clock system ====
SetupVCore(vcore1V5);
// Clk.SetMSI4MHz();
Clk.SetupFlashLatency(16);
Clk.SwitchToHSI();
Clk.UpdateFreqValues();
// Init OS
halInit();
chSysInit();
App.InitThread();
// ==== Init hardware ====
Uart.Init(115200, UART_GPIO, UART_TX_PIN);//, UART_GPIO, UART_RX_PIN);
Uart.Printf("\r%S %S\r", APP_NAME , BUILD_TIME);
Clk.PrintFreqs();
Effects.Init();
if(Radio.Init() == OK) {
// Effects.AllTogetherSmoothly(clGreen, 45);
// chEvtWaitAny(EVT_LEDS_DONE);
// Effects.AllTogetherSmoothly(clBlack, 45);
// chEvtWaitAny(EVT_LEDS_DONE);
}
else {
Effects.AllTogetherNow(clRed);
chThdSleepMilliseconds(180);
Effects.AllTogetherNow(clBlack);
chThdSleepMilliseconds(180);
Effects.AllTogetherNow(clRed);
chThdSleepMilliseconds(180);
Effects.AllTogetherNow(clBlack);
chThdSleepMilliseconds(180);
Effects.AllTogetherNow(clRed);
chThdSleepMilliseconds(180);
Effects.AllTogetherNow(clBlack);
}
// Effects.ChunkRunningRandom(clGreen, 2, 180);
Effects.ChunkRunningRandom(clYellow, 2, 0);
// Main cycle
App.ITask();
}
int main(void) {
// ==== Init Vcore & clock system ====
SetupVCore(vcore1V5);
Clk.UpdateFreqValues();
// ==== Init OS ====
halInit();
chSysInit();
// ==== Init Hard & Soft ====
Uart.Init(115200);
Uart.Printf("\rLocket AHB=%u", Clk.AHBFreqHz);
App.InitThread();
// App.LoadSettings();
// PinSensors.Init();
// Beeper.Init();
// Beeper.StartSequence(bsqBeepBeep);
Led.Init();
Led.StartSequence(lsqStart);
// Vibro.Init();
// Vibro.StartSequence(vsqBrrBrr);
// PinSetupOut(GPIOB, 8, omPushPull, pudNone);
// PinClear(GPIOB, 8);
// PwmPin_t IPin;
// IPin.Init(GPIOB, 8, TIM4, 3, 22);
// IPin.SetFreqHz(450);
// IPin.Set(11);
// Radio.Init();
// Main cycle
App.ITask();
}
int main(void) {
// ==== Init Vcore & clock system ====
SetupVCore(vcore1V5);
Clk.SetupFlashLatency(16);
uint8_t ClkRslt = Clk.SwitchToHSI();
if(ClkRslt == OK) Clk.DisableMSI();
Clk.UpdateFreqValues();
// ==== Init OS ====
halInit();
chSysInit();
// ==== Init Hard & Soft ====
Uart.Init(115200);
Uart.Printf("\rBmstuCtrl AHB=%u", Clk.AHBFreqHz);
if(ClkRslt != OK) Uart.Printf("\rClk switch failure");
// Path init
PinSetupOut(PATH_GPIO, PATH21_PIN, omPushPull);
PinSetupOut(PATH_GPIO, PATH31_PIN, omPushPull);
PinSetupOut(PATH_GPIO, PATH22_PIN, omPushPull);
PinSetupOut(PATH_GPIO, PATH32_PIN, omPushPull);
// Led init
PinSetupOut(LED_GPIO, LED_PIN, omPushPull);
// App.Init();
App.PThread = chThdSelf();
// Timers
chSysLock();
chVTSetI(&App.TmrUartRx, MS2ST(UART_RX_POLLING_MS), TmrUartRxCallback, nullptr);
chSysUnlock();
// Main cycle
while(true) App.ITask();
}
// Universal VirtualTimer callback
void TmrGeneralCallback(void *p) {
chSysLockFromIsr();
App.SignalEvtI((eventmask_t)p);
chSysUnlockFromIsr();
}