/**
* @brief Configures the analog watchdog.
* @note Analog watchdog thresholds can be modified while ADC conversion is on going.
* In this case, some constraints must be taken into account: the programmed threshold
* values are effective from the next ADC EOC (end of unitary conversion).
* Considering that registers write delay may happen due to bus activity, this might cause
* an uncertainty on the effective timing of the new programmed threshold values.
* @param hadc: pointer to a ADC_HandleTypeDef structure that contains
* the configuration information for the specified ADC.
* @param AnalogWDGConfig : pointer to an ADC_AnalogWDGConfTypeDef structure
* that contains the configuration information of ADC analog watchdog.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_ADC_AnalogWDGConfig(ADC_HandleTypeDef* hadc, ADC_AnalogWDGConfTypeDef* AnalogWDGConfig)
{
#ifdef USE_FULL_ASSERT
uint32_t tmp = 0;
#endif /* USE_FULL_ASSERT */
/* Check the parameters */
assert_param(IS_ADC_ANALOG_WATCHDOG(AnalogWDGConfig->WatchdogMode));
assert_param(IS_ADC_CHANNEL(AnalogWDGConfig->Channel));
assert_param(IS_FUNCTIONAL_STATE(AnalogWDGConfig->ITMode));
#ifdef USE_FULL_ASSERT
tmp = ADC_GET_RESOLUTION(hadc);
assert_param(IS_ADC_RANGE(tmp, AnalogWDGConfig->HighThreshold));
assert_param(IS_ADC_RANGE(tmp, AnalogWDGConfig->LowThreshold));
#endif /* USE_FULL_ASSERT */
/* Process locked */
__HAL_LOCK(hadc);
if(AnalogWDGConfig->ITMode == ENABLE)
{
/* Enable the ADC Analog watchdog interrupt */
__HAL_ADC_ENABLE_IT(hadc, ADC_IT_AWD);
}
else
{
/* Disable the ADC Analog watchdog interrupt */
__HAL_ADC_DISABLE_IT(hadc, ADC_IT_AWD);
}
/* Clear AWDEN, JAWDEN and AWDSGL bits */
hadc->Instance->CR1 &= ~(ADC_CR1_AWDSGL | ADC_CR1_JAWDEN | ADC_CR1_AWDEN);
/* Set the analog watchdog enable mode */
hadc->Instance->CR1 |= AnalogWDGConfig->WatchdogMode;
/* Set the high threshold */
hadc->Instance->HTR = AnalogWDGConfig->HighThreshold;
/* Set the low threshold */
hadc->Instance->LTR = AnalogWDGConfig->LowThreshold;
/* Clear the Analog watchdog channel select bits */
hadc->Instance->CR1 &= ~ADC_CR1_AWDCH;
/* Set the Analog watchdog channel */
hadc->Instance->CR1 |= (uint32_t)((uint16_t)(AnalogWDGConfig->Channel));
/* Process unlocked */
__HAL_UNLOCK(hadc);
/* Return function status */
return HAL_OK;
}
/**
* @brief Configures for the selected ADC injected channel its corresponding
* rank in the sequencer and its sample time.
* @param hadc: pointer to a ADC_HandleTypeDef structure that contains
* the configuration information for the specified ADC.
* @param sConfigInjected: ADC configuration structure for injected channel.
* @retval None
*/
HAL_StatusTypeDef HAL_ADCEx_InjectedConfigChannel(ADC_HandleTypeDef* hadc, ADC_InjectionConfTypeDef* sConfigInjected)
{
#ifdef USE_FULL_ASSERT
uint32_t tmp = 0;
#endif /* USE_FULL_ASSERT */
/* Check the parameters */
assert_param(IS_ADC_CHANNEL(sConfigInjected->InjectedChannel));
assert_param(IS_ADC_INJECTED_RANK(sConfigInjected->InjectedRank));
assert_param(IS_ADC_SAMPLE_TIME(sConfigInjected->InjectedSamplingTime));
assert_param(IS_ADC_EXT_INJEC_TRIG(sConfigInjected->ExternalTrigInjecConv));
assert_param(IS_ADC_INJECTED_LENGTH(sConfigInjected->InjectedNbrOfConversion));
assert_param(IS_FUNCTIONAL_STATE(sConfigInjected->AutoInjectedConv));
assert_param(IS_FUNCTIONAL_STATE(sConfigInjected->InjectedDiscontinuousConvMode));
#ifdef USE_FULL_ASSERT
tmp = ADC_GET_RESOLUTION(hadc);
assert_param(IS_ADC_RANGE(tmp, sConfigInjected->InjectedOffset));
#endif /* USE_FULL_ASSERT */
if(sConfigInjected->ExternalTrigInjecConvEdge != ADC_INJECTED_SOFTWARE_START)
{
assert_param(IS_ADC_EXT_INJEC_TRIG_EDGE(sConfigInjected->ExternalTrigInjecConvEdge));
}
/* Process locked */
__HAL_LOCK(hadc);
/* if ADC_Channel_10 ... ADC_Channel_18 is selected */
if (sConfigInjected->InjectedChannel > ADC_CHANNEL_9)
{
/* Clear the old sample time */
hadc->Instance->SMPR1 &= ~ADC_SMPR1(ADC_SMPR1_SMP10, sConfigInjected->InjectedChannel);
/* Set the new sample time */
hadc->Instance->SMPR1 |= ADC_SMPR1(sConfigInjected->InjectedSamplingTime, sConfigInjected->InjectedChannel);
}
else /* ADC_Channel include in ADC_Channel_[0..9] */
{
/* Clear the old sample time */
hadc->Instance->SMPR2 &= ~ADC_SMPR2(ADC_SMPR2_SMP0, sConfigInjected->InjectedChannel);
/* Set the new sample time */
hadc->Instance->SMPR2 |= ADC_SMPR2(sConfigInjected->InjectedSamplingTime, sConfigInjected->InjectedChannel);
}
/*---------------------------- ADCx JSQR Configuration -----------------*/
hadc->Instance->JSQR &= ~(ADC_JSQR_JL);
hadc->Instance->JSQR |= ADC_SQR1(sConfigInjected->InjectedNbrOfConversion);
/* Rank configuration */
/* Clear the old SQx bits for the selected rank */
hadc->Instance->JSQR &= ~ADC_JSQR(ADC_JSQR_JSQ1, sConfigInjected->InjectedRank,sConfigInjected->InjectedNbrOfConversion);
/* Set the SQx bits for the selected rank */
hadc->Instance->JSQR |= ADC_JSQR(sConfigInjected->InjectedChannel, sConfigInjected->InjectedRank,sConfigInjected->InjectedNbrOfConversion);
/* Enable external trigger if trigger selection is different of software */
/* start. */
/* Note: This configuration keeps the hardware feature of parameter */
/* ExternalTrigConvEdge "trigger edge none" equivalent to */
/* software start. */
if(sConfigInjected->ExternalTrigInjecConv != ADC_INJECTED_SOFTWARE_START)
{
/* Select external trigger to start conversion */
hadc->Instance->CR2 &= ~(ADC_CR2_JEXTSEL);
hadc->Instance->CR2 |= sConfigInjected->ExternalTrigInjecConv;
/* Select external trigger polarity */
hadc->Instance->CR2 &= ~(ADC_CR2_JEXTEN);
hadc->Instance->CR2 |= sConfigInjected->ExternalTrigInjecConvEdge;
}
else
{
/* Reset the external trigger */
hadc->Instance->CR2 &= ~(ADC_CR2_JEXTSEL);
hadc->Instance->CR2 &= ~(ADC_CR2_JEXTEN);
}
if (sConfigInjected->AutoInjectedConv != DISABLE)
{
/* Enable the selected ADC automatic injected group conversion */
hadc->Instance->CR1 |= ADC_CR1_JAUTO;
}
else
{
/* Disable the selected ADC automatic injected group conversion */
hadc->Instance->CR1 &= ~(ADC_CR1_JAUTO);
}
if (sConfigInjected->InjectedDiscontinuousConvMode != DISABLE)
{
/* Enable the selected ADC injected discontinuous mode */
hadc->Instance->CR1 |= ADC_CR1_JDISCEN;
}
else
{
/* Disable the selected ADC injected discontinuous mode */
hadc->Instance->CR1 &= ~(ADC_CR1_JDISCEN);
}
switch(sConfigInjected->InjectedRank)
{
case 1:
/* Set injected channel 1 offset */
hadc->Instance->JOFR1 &= ~(ADC_JOFR1_JOFFSET1);
hadc->Instance->JOFR1 |= sConfigInjected->InjectedOffset;
break;
case 2:
/* Set injected channel 2 offset */
hadc->Instance->JOFR2 &= ~(ADC_JOFR2_JOFFSET2);
hadc->Instance->JOFR2 |= sConfigInjected->InjectedOffset;
break;
case 3:
/* Set injected channel 3 offset */
hadc->Instance->JOFR3 &= ~(ADC_JOFR3_JOFFSET3);
hadc->Instance->JOFR3 |= sConfigInjected->InjectedOffset;
break;
default:
/* Set injected channel 4 offset */
hadc->Instance->JOFR4 &= ~(ADC_JOFR4_JOFFSET4);
hadc->Instance->JOFR4 |= sConfigInjected->InjectedOffset;
break;
}
/* if ADC1 Channel_18 is selected enable VBAT Channel */
if ((hadc->Instance == ADC1) && (sConfigInjected->InjectedChannel == ADC_CHANNEL_VBAT))
{
/* Enable the VBAT channel*/
ADC->CCR |= ADC_CCR_VBATE;
}
/* if ADC1 Channel_16 or Channel_17 is selected enable TSVREFE Channel(Temperature sensor and VREFINT) */
if ((hadc->Instance == ADC1) && ((sConfigInjected->InjectedChannel == ADC_CHANNEL_TEMPSENSOR) || (sConfigInjected->InjectedChannel == ADC_CHANNEL_VREFINT)))
{
/* Enable the TSVREFE channel*/
ADC->CCR |= ADC_CCR_TSVREFE;
}
/* Process unlocked */
__HAL_UNLOCK(hadc);
/* Return function status */
return HAL_OK;
}