/**
*\brief Erases the specified 64KB block of the serial firmware dataflash.
*
* \param pAt25 Pointer to an AT25 driver instance.
* \param address Address of the block to erase.
*
* \return 0 if successful; otherwise returns AT25_ERROR_PROTECTED if the
* device is protected or AT25_ERROR_BUSY if it is busy executing a command.
*/
unsigned char AT25D_EraseBlock(At25 *pAt25, unsigned int address)
{
unsigned char status;
unsigned char error;
assert(pAt25);
/* Check that the flash is ready and unprotected */
status = AT25D_ReadStatus(pAt25);
if ((status & AT25_STATUS_RDYBSY) != AT25_STATUS_RDYBSY_READY) {
TRACE_ERROR("AT25D_EraseBlock : Flash busy\n\r");
return AT25_ERROR_BUSY;
}
else if ((status & AT25_STATUS_SWP) != AT25_STATUS_SWP_PROTNONE) {
TRACE_ERROR("AT25D_EraseBlock : Flash protected\n\r");
return AT25_ERROR_PROTECTED;
}
/* Enable critical write operation */
AT25D_EnableWrite(pAt25);
/* Start the block erase command */
error = AT25_SendCommand(pAt25, AT25_BlockEraseCmd(pAt25), 4, 0, 0, address, 0, 0);
assert(!error);
/* Wait for transfer to finish */
AT25D_Wait(pAt25);
/* Poll the Serial flash status register until the operation is achieved */
AT25D_WaitReady(pAt25);
return 0;
}
/**
* \brief Erases all the content of the memory chip.
*
* \param pAt25 Pointer to an AT25 driver instance.
*
* \return 0 if the device has been unprotected; otherwise returns
* AT25_ERROR_PROTECTED.
*/
unsigned char AT25D_EraseChip(At25 *pAt25)
{
unsigned char status;
unsigned char error;
assert(pAt25);
/* Check that the flash is unprotected */
status = AT25D_ReadStatus(pAt25);
if ((status & AT25_STATUS_SWP) != AT25_STATUS_SWP_PROTNONE) {
return AT25_ERROR_PROTECTED;
}
/* Enable critical write operation */
AT25D_EnableWrite(pAt25);
/* Erase the chip */
error = AT25_SendCommand(pAt25, AT25_CHIP_ERASE_2, 1, 0, 0, 0, 0, 0);
assert(!error);
/* Wait for transfer to finish */
AT25D_Wait(pAt25);
/* Poll the Serial flash status register until the operation is achieved */
AT25D_WaitReady(pAt25);
return 0;
}
/**
* \brief Disables write operation on a serial flash device.
*
* \para pAt25 Pointer to an AT25 driver instance.
*/
void AT25D_DisableWrite(At25 *pAt25)
{
unsigned char error;
assert(pAt25);
/* Issue a write enable command */
error = AT25_SendCommand(pAt25, AT25_WRITE_DISABLE, 1, 0, 0, 0, 0, 0);
assert(!error);
/* Wait for transfer to finish */
AT25D_Wait(pAt25);
}
/**
* \brief Writes the given value in the status register of the serial flash device.
*
* \param pAt25 Pointer to an AT25 driver instance.
* \param status Status to write.
*/
static void AT25D_WriteStatus(At25 *pAt25, unsigned char status)
{
unsigned char error;
assert(pAt25);
/* Issue a write status command */
error = AT25_SendCommand(pAt25, AT25_WRITE_STATUS, 1, &status, 1, 0, 0, 0);
assert(!error);
/* Wait for transfer to finish */
AT25D_Wait(pAt25);
}
/**
* \brief Writes data at the specified address on the serial firmware dataflash. The
* page(s) to program must have been erased prior to writing. This function
* handles page boundary crossing automatically.
*
* \param pAt25 Pointer to an AT25 driver instance.
* \param pData Data buffer.
* \param size Number of bytes in buffer.
* \param address Write address.
*
* \return 0 if successful; otherwise, returns AT25_ERROR_PROGRAM is there has
* been an error during the data programming.
*/
unsigned char AT25D_Write(
At25 *pAt25,
unsigned char *pData,
unsigned int size,
unsigned int address)
{
unsigned int pageSize;
unsigned int writeSize;
unsigned char error;
unsigned char status;
assert(pAt25);
assert(pData);
/* Retrieve device page size */
pageSize = AT25_PageSize(pAt25);
/* Program one page after the other */
while (size > 0) {
/* Compute number of bytes to program in page */
writeSize = min(size, pageSize - (address % pageSize));
/* Enable critical write operation */
AT25D_EnableWrite(pAt25);
/* Program page */
error = AT25_SendCommand(pAt25, AT25_BYTE_PAGE_PROGRAM, 4,
pData, writeSize, address, 0, 0);
assert(!error);
/* Wait for transfer to finish */
AT25D_Wait(pAt25);
/* Poll the Serial flash status register until the operation is achieved */
AT25D_WaitReady(pAt25);
/* Make sure that write was without error */
status = AT25D_ReadStatus(pAt25);
if ((status & AT25_STATUS_EPE) == AT25_STATUS_EPE_ERROR) {
return AT25_ERROR_PROGRAM;
}
pData += writeSize;
size -= writeSize;
address += writeSize;
}
return 0;
}
/**
* \brief Reads and returns the status register of the serial flash.
*
* \param pAt25 Pointer to an AT25 driver instance.
*/
static unsigned char AT25D_ReadStatus(At25 *pAt25)
{
unsigned char error, status;
assert(pAt25);
/* Issue a status read command */
error = AT25_SendCommand(pAt25, AT25_READ_STATUS, 1, &status, 1, 0, 0, 0);
assert(!error);
/* Wait for transfer to finish */
AT25D_Wait(pAt25);
return status;
}
/**
* \brief Reads data from the specified address on the serial flash.
*
* \param pAt25 Pointer to an AT25 driver instance.
* \param pData Data buffer.
* \param size Number of bytes to read.
* \param address Read address.
*
* \return 0 if successful; otherwise, fail.
*/
unsigned char AT25D_Read(
At25 *pAt25,
unsigned char *pData,
unsigned int size,
unsigned int address)
{
unsigned char error;
/* Start a read operation */
error = AT25_SendCommand(pAt25, AT25_READ_ARRAY_LF, 4, pData, size, address, 0, 0);
assert(!error);
/* Wait for transfer to finish */
AT25D_Wait(pAt25);
return error;
}
/**
* \brief Reads and returns the serial flash device ID.
*
* \param pAt25 Pointer to an AT25 driver instance.
*/
unsigned int AT25D_ReadJedecId(At25 *pAt25)
{
unsigned char error;
unsigned int id = 0;
assert(pAt25);
/* Issue a read ID command */
error = AT25_SendCommand(pAt25, AT25_READ_JEDEC_ID, 1,
(unsigned char *) &id, 3, 0, 0, 0);
assert(!error);
/* Wait for transfer to finish */
AT25D_Wait(pAt25);
return id;
}