Ejemplos de AT91C_LPDDRC2_DS en C++ (Cpp)

Ejemplo n.º 1

Archivo: sama5d2_xplained.c Proyecto: ChristianHackAMS/at91bootstrap

static void lpddr2_reg_config(struct ddramc_register *ddramc_config)
{
	ddramc_config->mdr = (AT91C_DDRC2_DBW_32_BITS |
			      AT91C_DDRC2_MD_LPDDR2_SDRAM);

	ddramc_config->cr = (AT91C_DDRC2_NC_DDR10_SDR9 |
			     AT91C_DDRC2_NR_14 |
			     AT91C_DDRC2_CAS_3 |
			     AT91C_DDRC2_ZQ_SHORT |
			     AT91C_DDRC2_NB_BANKS_8 |
			     AT91C_DDRC2_UNAL_SUPPORTED);

	ddramc_config->lpddr2_lpr = AT91C_LPDDRC2_DS(0x03);

#ifdef CONFIG_BUS_SPEED_166MHZ
	/*
	 * The MT42128M32 refresh window: 32ms
	 * Required number of REFRESH commands(MIN): 8192
	 * (32ms / 8192) * 166MHz = 0x288.
	 */
	ddramc_config->rtr = 0x288;
	/* 90n short calibration: ZQCS */
	ddramc_config->tim_calr = AT91C_DDRC2_ZQCS(12);

	ddramc_config->t0pr = (AT91C_DDRC2_TRAS_(7) |
			       AT91C_DDRC2_TRCD_(3) |
			       AT91C_DDRC2_TWR_(3) |
			       AT91C_DDRC2_TRC_(11) |
			       AT91C_DDRC2_TRP_(4) |
			       AT91C_DDRC2_TRRD_(2) |
			       AT91C_DDRC2_TWTR_(2) |
			       AT91C_DDRC2_TMRD_(3));

	ddramc_config->t1pr = (AT91C_DDRC2_TRFC_(35) |
				AT91C_DDRC2_TXSNR_(37) |
				AT91C_DDRC2_TXSRD_(0) |
				AT91C_DDRC2_TXP_(2));

	ddramc_config->t2pr = (AT91C_DDRC2_TXARD_(0) |
			       AT91C_DDRC2_TXARDS_(0) |
			       AT91C_DDRC2_TRPA_(0) |
			       AT91C_DDRC2_TRTP_(2) |
			       AT91C_DDRC2_TFAW_(9));
#else
#error "No CLK setting defined"
#endif
}

Ejemplo n.º 2

Archivo: sama5d3x_cmp.c Proyecto: biagiom/at91bootstrap

static void lpddr2_reg_config(struct ddramc_register *ddramc_config)
{
	ddramc_config->mdr = (AT91C_DDRC2_DBW_32_BITS
				| AT91C_DDRC2_MD_LPDDR2_SDRAM);

	ddramc_config->cr = (AT91C_DDRC2_NC_DDR10_SDR9
				| AT91C_DDRC2_NR_14
				| AT91C_DDRC2_CAS_3
				| AT91C_DDRC2_ZQ_SHORT
				| AT91C_DDRC2_NB_BANKS_8
				| AT91C_DDRC2_UNAL_SUPPORTED);

	ddramc_config->lpddr2_lpr = AT91C_LPDDRC2_DS(0x03);
	/* 90n short calibration: ZQCS */
	ddramc_config->tim_calr = AT91C_DDRC2_ZQCS(12);

	/*
	 * The MT42128M32 refresh window: 32ms
	 * Required number of REFRESH commands(MIN): 8192
	 * (32ms / 8192) * 132MHz = 514 i.e. 0x202
	 */
	ddramc_config->rtr = 0x202;

	ddramc_config->cal_mr4r = AT91C_DDRC2_COUNT_CAL(0xC852);

	ddramc_config->t0pr = (AT91C_DDRC2_TRAS_(6)
			| AT91C_DDRC2_TRCD_(2)
			| AT91C_DDRC2_TWR_(3)
			| AT91C_DDRC2_TRC_(8)
			| AT91C_DDRC2_TRP_(2)
			| AT91C_DDRC2_TRRD_(2)
			| AT91C_DDRC2_TWTR_(2)
			| AT91C_DDRC2_TMRD_(3));

	ddramc_config->t1pr = (AT91C_DDRC2_TXP_(2)
			| AT91C_DDRC2_TXSNR_(18)
			| AT91C_DDRC2_TRFC_(17));

	ddramc_config->t2pr = (AT91C_DDRC2_TFAW_(8)
			| AT91C_DDRC2_TRTP_(2)
			| AT91C_DDRC2_TRPA_(3)
			| AT91C_DDRC2_TXARDS_(1)
			| AT91C_DDRC2_TXARD_(1));
}

Ejemplo n.º 3

Archivo: sama5d2_xplained.c Proyecto: digideskio/at91bootstrap

static void lpddr3_reg_config(struct ddramc_register *ddramc_config)
{
	ddramc_config->mdr = (AT91C_DDRC2_DBW_32_BITS |
			      AT91C_DDRC2_MD_LPDDR3_SDRAM);

	ddramc_config->cr = (AT91C_DDRC2_NC_DDR10_SDR9 |
			     AT91C_DDRC2_NR_14 |
			     AT91C_DDRC2_CAS_3 |
			     AT91C_DDRC2_ZQ_INIT |
			     AT91C_DDRC2_NB_BANKS_8 |
			     AT91C_DDRC2_DECOD_SEQUENTIAL |
			     AT91C_DDRC2_UNAL_SUPPORTED);

	ddramc_config->lpddr2_lpr = AT91C_LPDDRC2_DS(0x04);

#ifdef CONFIG_BUS_SPEED_166MHZ
	/* The low-power DDR3-SDRAM device requires a refresh every 3.9 us.*/
	ddramc_config->rtr = 0x288;

	ddramc_config->t0pr = (AT91C_DDRC2_TRAS_(7) |
			       AT91C_DDRC2_TRCD_(3) |
			       AT91C_DDRC2_TWR_(3) |
			       AT91C_DDRC2_TRC_(11) |
			       AT91C_DDRC2_TRP_(4) |
			       AT91C_DDRC2_TRRD_(2) |
			       AT91C_DDRC2_TWTR_(4) |
			       AT91C_DDRC2_TMRD_(10));

	ddramc_config->t1pr = (AT91C_DDRC2_TRFC_(35) |
			       AT91C_DDRC2_TXSNR_(37) |
			       AT91C_DDRC2_TXSRD_(0) |
			       AT91C_DDRC2_TXP_(2));

	ddramc_config->t2pr = (AT91C_DDRC2_TXARD_(0) |
			       AT91C_DDRC2_TXARDS_(0) |
			       AT91C_DDRC2_TRPA_(0) |
			       AT91C_DDRC2_TRTP_(4) |
			       AT91C_DDRC2_TFAW_(9));
#else
#error "No CLK setting defined"
#endif
}