static void __init eco920_board_init(void)
{
/* DBGU on ttyS0. (Rx & Tx only */
at91_register_uart(0, 0, 0);
at91_add_device_serial();
at91_add_device_eth(&eco920_eth_data);
at91_add_device_usbh(&eco920_usbh_data);
at91_add_device_udc(&eco920_udc_data);
at91_add_device_mci(0, &eco920_mci0_data);
platform_device_register(&eco920_flash);
at91_ramc_write(0, AT91_SMC_CSR(7), AT91_SMC_RWHOLD_(1)
| AT91_SMC_RWSETUP_(1)
| AT91_SMC_DBW_8
| AT91_SMC_WSEN
| AT91_SMC_NWS_(15));
at91_set_A_periph(AT91_PIN_PC6, 1);
at91_set_gpio_input(AT91_PIN_PA23, 0);
at91_set_deglitch(AT91_PIN_PA23, 1);
/* Initialization of the Static Memory Controller for Chip Select 3 */
at91_ramc_write(0, AT91_SMC_CSR(3),
AT91_SMC_DBW_16 | /* 16 bit */
AT91_SMC_WSEN |
AT91_SMC_NWS_(5) | /* wait states */
AT91_SMC_TDF_(1) /* float time */
);
at91_add_device_spi(eco920_spi_devices, ARRAY_SIZE(eco920_spi_devices));
/* LEDs */
at91_gpio_leds(eco920_leds, ARRAY_SIZE(eco920_leds));
}
static void yl9200_init_video(void)
{
/* NWAIT Signal */
at91_set_A_periph(AT91_PIN_PC6, 0);
/* Initialization of the Static Memory Controller for Chip Select 2 */
at91_ramc_write(0, AT91_SMC_CSR(2), AT91_SMC_DBW_16 /* 16 bit */
| AT91_SMC_WSEN | AT91_SMC_NWS_(0x4) /* wait states */
| AT91_SMC_TDF_(0x100) /* float time */
);
}
void __init at91_add_device_cf(struct at91_cf_data *data)
{
unsigned int csa;
if (!data)
return;
data->chipselect = 4; /* can only use EBI ChipSelect 4 */
/* CF takes over CS4, CS5, CS6 */
csa = at91_ramc_read(0, AT91_EBI_CSA);
at91_ramc_write(0, AT91_EBI_CSA, csa | AT91_EBI_CS4A_SMC_COMPACTFLASH);
/*
* Static memory controller timing adjustments.
* REVISIT: these timings are in terms of MCK cycles, so
* when MCK changes (cpufreq etc) so must these values...
*/
at91_ramc_write(0, AT91_SMC_CSR(4),
AT91_SMC_ACSS_STD
| AT91_SMC_DBW_16
| AT91_SMC_BAT
| AT91_SMC_WSEN
| AT91_SMC_NWS_(32) /* wait states */
| AT91_SMC_RWSETUP_(6) /* setup time */
| AT91_SMC_RWHOLD_(4) /* hold time */
);
/* input/irq */
if (gpio_is_valid(data->irq_pin)) {
at91_set_gpio_input(data->irq_pin, 1);
at91_set_deglitch(data->irq_pin, 1);
}
at91_set_gpio_input(data->det_pin, 1);
at91_set_deglitch(data->det_pin, 1);
/* outputs, initially off */
if (gpio_is_valid(data->vcc_pin))
at91_set_gpio_output(data->vcc_pin, 0);
at91_set_gpio_output(data->rst_pin, 0);
/* force poweron defaults for these pins ... */
at91_set_A_periph(AT91_PIN_PC9, 0); /* A25/CFRNW */
at91_set_A_periph(AT91_PIN_PC10, 0); /* NCS4/CFCS */
at91_set_A_periph(AT91_PIN_PC11, 0); /* NCS5/CFCE1 */
at91_set_A_periph(AT91_PIN_PC12, 0); /* NCS6/CFCE2 */
/* nWAIT is _not_ a default setting */
at91_set_A_periph(AT91_PIN_PC6, 1); /* nWAIT */
cf_data = *data;
platform_device_register(&at91rm9200_cf_device);
}
static void __init ek_init_video(void)
{
/* NWAIT Signal */
at91_set_A_periph(AT91_PIN_PC6, 0);
/* Initialization of the Static Memory Controller for Chip Select 3 */
at91_sys_write(AT91_SMC_CSR(3), AT91_SMC_DBW_16 /* 16 bit */
| AT91_SMC_WSEN | AT91_SMC_NWS_(5) /* wait states */
| AT91_SMC_TDF_(1) /* float time */
);
at91_ics1523_init();
}
/* we already mapped the I/O region */
static int at91_cf_set_io_map(struct pcmcia_socket *s, struct pccard_io_map *io)
{
struct at91_cf_socket *cf;
u32 csr;
cf = container_of(s, struct at91_cf_socket, socket);
io->flags &= (MAP_ACTIVE | MAP_16BIT | MAP_AUTOSZ);
/*
* Use 16 bit accesses unless/until we need 8-bit i/o space.
* Always set CSR4 ... PCMCIA won't always unmap things.
*/
csr = at91_sys_read(AT91_SMC_CSR(4)) & ~AT91_SMC_DBW;
/*
* NOTE: this CF controller ignores IOIS16, so we can't really do
* MAP_AUTOSZ. The 16bit mode allows single byte access on either
* D0-D7 (even addr) or D8-D15 (odd), so it's close enough for many
* purposes (and handles ide-cs).
*
* The 8bit mode is needed for odd byte access on D0-D7. It seems
* some cards only like that way to get at the odd byte, despite
* CF 3.0 spec table 35 also giving the D8-D15 option.
*/
if (!(io->flags & (MAP_16BIT|MAP_AUTOSZ))) {
csr |= AT91_SMC_DBW_8;
pr_debug("%s: 8bit i/o bus\n", driver_name);
} else {
csr |= AT91_SMC_DBW_16;
pr_debug("%s: 16bit i/o bus\n", driver_name);
}
at91_sys_write(AT91_SMC_CSR(4), csr);
io->start = cf->socket.io_offset;
io->stop = io->start + SZ_2K - 1;
return 0;
}
static int at91_cf_set_io_map(struct pcmcia_socket *s, struct pccard_io_map *io)
{
struct at91_cf_socket *cf;
u32 csr;
cf = container_of(s, struct at91_cf_socket, socket);
io->flags &= (MAP_ACTIVE | MAP_16BIT | MAP_AUTOSZ);
/*
*/
csr = at91_ramc_read(0, AT91_SMC_CSR(cf->board->chipselect)) & ~AT91_SMC_DBW;
/*
*/
if (!(io->flags & (MAP_16BIT | MAP_AUTOSZ))) {
csr |= AT91_SMC_DBW_8;
pr_debug("%s: 8bit i/o bus\n", driver_name);
} else {
csr |= AT91_SMC_DBW_16;
pr_debug("%s: 16bit i/o bus\n", driver_name);
}
at91_ramc_write(0, AT91_SMC_CSR(cf->board->chipselect), csr);
io->start = cf->socket.io_offset;
io->stop = io->start + SZ_2K - 1;
return 0;
}
static void __init yl_9200_init_video(void)
{
at91_sys_write(AT91_PIOC + PIO_ASR,AT91_PIN_PC6);
at91_sys_write(AT91_PIOC + PIO_BSR,0);
at91_sys_write(AT91_PIOC + PIO_ASR,AT91_PIN_PC6);
at91_sys_write( AT91_SMC_CSR(2),
AT91_SMC_NWS_(0x4) |
AT91_SMC_WSEN |
AT91_SMC_TDF_(0x100) |
AT91_SMC_DBW
);
}
/*
* Enable NAND and detect card.
*/
static void at91_nand_enable(struct at91_nand_host *host)
{
unsigned int csa;
/* Setup Smart Media, first enable the address range of CS3 */
csa = at91_sys_read(AT91_EBI_CSA);
at91_sys_write(AT91_EBI_CSA, csa | AT91_EBI_CS3A_SMC_SMARTMEDIA);
/* set the bus interface characteristics */
at91_sys_write(AT91_SMC_CSR(3), AT91_SMC_ACSS_STD | AT91_SMC_DBW_8 | AT91_SMC_WSEN
| AT91_SMC_NWS_(5)
| AT91_SMC_TDF_(1)
| AT91_SMC_RWSETUP_(0) /* tDS Data Set up Time 30 - ns */
| AT91_SMC_RWHOLD_(1) /* tDH Data Hold Time 20 - ns */
);
if (host->board->enable_pin)
at91_set_gpio_value(host->board->enable_pin, 0);
}
void __init at91_add_device_nand(struct atmel_nand_data *data)
{
unsigned int csa;
if (!data)
return;
/* enable the address range of CS3 */
csa = at91_ramc_read(0, AT91_EBI_CSA);
at91_ramc_write(0, AT91_EBI_CSA, csa | AT91_EBI_CS3A_SMC_SMARTMEDIA);
/* set the bus interface characteristics */
at91_ramc_write(0, AT91_SMC_CSR(3), AT91_SMC_ACSS_STD | AT91_SMC_DBW_8 | AT91_SMC_WSEN
| AT91_SMC_NWS_(5)
| AT91_SMC_TDF_(1)
| AT91_SMC_RWSETUP_(0) /* tDS Data Set up Time 30 - ns */
| AT91_SMC_RWHOLD_(1) /* tDH Data Hold Time 20 - ns */
);
/* enable pin */
if (gpio_is_valid(data->enable_pin))
at91_set_gpio_output(data->enable_pin, 1);
/* ready/busy pin */
if (gpio_is_valid(data->rdy_pin))
at91_set_gpio_input(data->rdy_pin, 1);
/* card detect pin */
if (gpio_is_valid(data->det_pin))
at91_set_gpio_input(data->det_pin, 1);
at91_set_A_periph(AT91_PIN_PC1, 0); /* SMOE */
at91_set_A_periph(AT91_PIN_PC3, 0); /* SMWE */
nand_data = *data;
platform_device_register(&at91rm9200_nand_device);
}
void __init at91_add_device_nand(struct atmel_nand_data *data)
{
unsigned int csa;
if (!data)
return;
/* enable the address range of CS3 */
csa = at91_sys_read(AT91_EBI_CSA);
at91_sys_write(AT91_EBI_CSA, csa | AT91_EBI_CS3A_SMC_SMARTMEDIA);
/* set the bus interface characteristics */
at91_sys_write(AT91_SMC_CSR(3), AT91_SMC_ACSS_STD | AT91_SMC_DBW_8 | AT91_SMC_WSEN
| AT91_SMC_NWS_(5)
| AT91_SMC_TDF_(1)
| AT91_SMC_RWSETUP_(0) /* tDS Data Set up Time 30 - ns */
| AT91_SMC_RWHOLD_(1) /* tDH Data Hold Time 20 - ns */
);
/* enable pin */
if (data->enable_pin)
at91_set_gpio_output(data->enable_pin, 1);
/* ready/busy pin */
if (data->rdy_pin)
at91_set_gpio_input(data->rdy_pin, 1);
/* card detect pin */
if (data->det_pin)
at91_set_gpio_input(data->det_pin, 1);
at91_set_A_periph(AT91_PIN_PC1, 0); /* SMOE */
at91_set_A_periph(AT91_PIN_PC3, 0); /* SMWE */
add_generic_device("atmel_nand", 0, NULL, AT91_CHIPSELECT_3, 0x10,
IORESOURCE_MEM, data);
}
static int __init at91_cf_probe(struct device *dev)
{
struct at91_cf_socket *cf;
struct at91_cf_data *board = dev->platform_data;
struct platform_device *pdev = to_platform_device(dev);
struct resource *io;
unsigned int csa;
int status;
if (!board || !board->det_pin || !board->rst_pin)
return -ENODEV;
io = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!io)
return -ENODEV;
cf = kcalloc(1, sizeof *cf, GFP_KERNEL);
if (!cf)
return -ENOMEM;
cf->board = board;
cf->pdev = pdev;
dev_set_drvdata(dev, cf);
/* CF takes over CS4, CS5, CS6 */
csa = at91_sys_read(AT91_EBI_CSA);
at91_sys_write(AT91_EBI_CSA, csa | AT91_EBI_CS4A_SMC_COMPACTFLASH);
/* force poweron defaults for these pins ... */
(void) at91_set_A_periph(AT91_PIN_PC9, 0); /* A25/CFRNW */
(void) at91_set_A_periph(AT91_PIN_PC10, 0); /* NCS4/CFCS */
(void) at91_set_A_periph(AT91_PIN_PC11, 0); /* NCS5/CFCE1 */
(void) at91_set_A_periph(AT91_PIN_PC12, 0); /* NCS6/CFCE2 */
/* nWAIT is _not_ a default setting */
(void) at91_set_A_periph(AT91_PIN_PC6, 1); /* nWAIT */
/*
* Static memory controller timing adjustments.
* REVISIT: these timings are in terms of MCK cycles, so
* when MCK changes (cpufreq etc) so must these values...
*/
at91_sys_write(AT91_SMC_CSR(4),
AT91_SMC_ACSS_STD
| AT91_SMC_DBW_16
| AT91_SMC_BAT
| AT91_SMC_WSEN
| AT91_SMC_NWS_(32) /* wait states */
| AT91_SMC_RWSETUP_(6) /* setup time */
| AT91_SMC_RWHOLD_(4) /* hold time */
);
/* must be a GPIO; ergo must trigger on both edges */
status = request_irq(board->det_pin, at91_cf_irq,
SA_SAMPLE_RANDOM, driver_name, cf);
if (status < 0)
goto fail0;
/*
* The card driver will request this irq later as needed.
* but it causes lots of "irqNN: nobody cared" messages
* unless we report that we handle everything (sigh).
* (Note: DK board doesn't wire the IRQ pin...)
*/
if (board->irq_pin) {
status = request_irq(board->irq_pin, at91_cf_irq,
SA_SHIRQ, driver_name, cf);
if (status < 0)
goto fail0a;
cf->socket.pci_irq = board->irq_pin;
} else
cf->socket.pci_irq = NR_IRQS + 1;
/* pcmcia layer only remaps "real" memory not iospace */
cf->socket.io_offset = (unsigned long) ioremap(CF_IO_PHYS, SZ_2K);
if (!cf->socket.io_offset)
goto fail1;
/* reserve CS4, CS5, and CS6 regions; but use just CS4 */
if (!request_mem_region(io->start, io->end + 1 - io->start,
driver_name))
goto fail1;
pr_info("%s: irqs det #%d, io #%d\n", driver_name,
board->det_pin, board->irq_pin);
cf->socket.owner = THIS_MODULE;
cf->socket.dev.dev = dev;
cf->socket.ops = &at91_cf_ops;
cf->socket.resource_ops = &pccard_static_ops;
cf->socket.features = SS_CAP_PCCARD | SS_CAP_STATIC_MAP
| SS_CAP_MEM_ALIGN;
cf->socket.map_size = SZ_2K;
cf->socket.io[0].res = io;
status = pcmcia_register_socket(&cf->socket);
if (status < 0)
goto fail2;
return 0;
fail2:
iounmap((void __iomem *) cf->socket.io_offset);
release_mem_region(io->start, io->end + 1 - io->start);
fail1:
if (board->irq_pin)
free_irq(board->irq_pin, cf);
fail0a:
free_irq(board->det_pin, cf);
fail0:
at91_sys_write(AT91_EBI_CSA, csa);
kfree(cf);
return status;
}