/*
* disable the divil module bar space.
*/
static void divil_lbar_disable(void)
{
u32 hi, lo;
int offset;
for (offset = DIVIL_LBAR_SMB; offset <= DIVIL_LBAR_PMS; offset++) {
_rdmsr(DIVIL_MSR_REG(offset), &hi, &lo);
hi &= ~0x01;
_wrmsr(DIVIL_MSR_REG(offset), hi, lo);
}
}
/*
* enable the divil module bar space.
*
* For all the DIVIL module LBAR, you should control the DIVIL LBAR reg
* and the RCONFx(0~5) reg to use the modules.
*/
static void divil_lbar_enable(void)
{
u32 hi, lo;
int offset;
/*
* The DIVIL IRQ is not used yet. and make the RCONF0 reserved.
*/
for (offset = DIVIL_LBAR_SMB; offset <= DIVIL_LBAR_PMS; offset++) {
_rdmsr(DIVIL_MSR_REG(offset), &hi, &lo);
hi |= 0x01;
_wrmsr(DIVIL_MSR_REG(offset), hi, lo);
}
}
static void get_gpio_base(void)
{
unsigned int hi, lo;
_rdmsr(DIVIL_MSR_REG(DIVIL_LBAR_GPIO), &hi, &lo);
GPIO_BASE_ADDR = lo;
printf("GPIO_BASE_ADDR is %x\n", GPIO_BASE_ADDR);
gpio_base_inited = 1;
}
static void fl2f_reboot(void)
{
reset_cpu();
/* send a reset signal to south bridge.
*
* NOTE: if enable "Power Management" in kernel, rtl8169 will not reset
* normally with this reset operation and it will not work in PMON, but
* you can type halt command and then reboot, seems the hardware reset
* logic not work normally.
*/
{
u32 hi, lo;
_rdmsr(DIVIL_MSR_REG(DIVIL_SOFT_RESET), &hi, &lo);
lo |= 0x00000001;
_wrmsr(DIVIL_MSR_REG(DIVIL_SOFT_RESET), hi, lo);
}
}
static irqreturn_t timer_interrupt(int irq, void *dev_id)
{
u32 basehi;
_rdmsr(DIVIL_MSR_REG(DIVIL_LBAR_MFGPT), &basehi, &mfgpt_base);
outw(inw(MFGPT0_SETUP) | 0x4000, MFGPT0_SETUP);
mfgpt_clockevent.event_handler(&mfgpt_clockevent);
return IRQ_HANDLED;
}
void __init setup_mfgpt0_timer(void)
{
u32 basehi;
struct clock_event_device *cd = &mfgpt_clockevent;
unsigned int cpu = smp_processor_id();
cd->cpumask = cpumask_of(cpu);
clockevent_set_clock(cd, MFGPT_TICK_RATE);
cd->max_delta_ns = clockevent_delta2ns(0xffff, cd);
cd->min_delta_ns = clockevent_delta2ns(0xf, cd);
_wrmsr(DIVIL_MSR_REG(MFGPT_IRQ), 0, 0x100);
_wrmsr(DIVIL_MSR_REG(PIC_ZSEL_LOW), 0, 0x50000);
_rdmsr(DIVIL_MSR_REG(DIVIL_LBAR_MFGPT), &basehi, &mfgpt_base);
clockevents_register_device(cd);
setup_irq(CS5536_MFGPT_INTR, &irq5);
}
/*
* Initialize the conversion factor and the min/max deltas of the clock event
* structure and register the clock event source with the framework.
*/
void __init setup_mfgpt0_timer(void)
{
u32 basehi;
struct clock_event_device *cd = &mfgpt_clockevent;
unsigned int cpu = smp_processor_id();
cd->cpumask = cpumask_of(cpu);
clockevent_set_clock(cd, MFGPT_TICK_RATE);
cd->max_delta_ns = clockevent_delta2ns(0xffff, cd);
cd->min_delta_ns = clockevent_delta2ns(0xf, cd);
/* Enable MFGPT0 Comparator 2 Output to the Interrupt Mapper */
_wrmsr(DIVIL_MSR_REG(MFGPT_IRQ), 0, 0x100);
/* Enable Interrupt Gate 5 */
_wrmsr(DIVIL_MSR_REG(PIC_ZSEL_LOW), 0, 0x50000);
/* get MFGPT base address */
_rdmsr(DIVIL_MSR_REG(DIVIL_LBAR_MFGPT), &basehi, &mfgpt_base);
clockevents_register_device(cd);
setup_irq(CS5536_MFGPT_INTR, &irq5);
}
static irqreturn_t timer_interrupt(int irq, void *dev_id)
{
u32 basehi;
/*
* get MFGPT base address
*
* NOTE: do not remove me, it's need for the value of mfgpt_base is
* variable
*/
_rdmsr(DIVIL_MSR_REG(DIVIL_LBAR_MFGPT), &basehi, &mfgpt_base);
/* ack */
outw(inw(MFGPT0_SETUP) | 0x4000, MFGPT0_SETUP);
mfgpt_clockevent.event_handler(&mfgpt_clockevent);
return IRQ_HANDLED;
}
static void fl2f_shutdown(void)
{
u32 hi, lo, val;
int gpio_base;
/* get gpio base */
_rdmsr(DIVIL_MSR_REG(DIVIL_LBAR_GPIO), &hi, &lo);
gpio_base = lo & 0xff00;
/* make cs5536 gpio13 output enable */
val = inl(gpio_base + GPIOL_OUT_EN);
val &= ~(1 << (16 + 13));
val |= (1 << 13);
outl(val, gpio_base + GPIOL_OUT_EN);
mmiowb();
/* make cs5536 gpio13 output low level voltage. */
val = inl(gpio_base + GPIOL_OUT_VAL) & ~(1 << (13));
val |= (1 << (16 + 13));
outl(val, gpio_base + GPIOL_OUT_VAL);
mmiowb();
}
/*
* isa_read: ISA read transfers
*
* We assume that this is not a bus master transfer.
*/
u32 pci_isa_read_reg(int reg)
{
u32 conf_data = 0;
u32 hi, lo;
switch (reg) {
case PCI_VENDOR_ID:
conf_data =
CFG_PCI_VENDOR_ID(CS5536_ISA_DEVICE_ID, CS5536_VENDOR_ID);
break;
case PCI_COMMAND:
/* we just check the first LBAR for the IO enable bit, */
/* maybe we should changed later. */
_rdmsr(DIVIL_MSR_REG(DIVIL_LBAR_SMB), &hi, &lo);
if (hi & 0x01)
conf_data |= PCI_COMMAND_IO;
break;
case PCI_STATUS:
conf_data |= PCI_STATUS_66MHZ;
conf_data |= PCI_STATUS_DEVSEL_MEDIUM;
conf_data |= PCI_STATUS_FAST_BACK;
_rdmsr(SB_MSR_REG(SB_ERROR), &hi, &lo);
if (lo & SB_TAS_ERR_FLAG)
conf_data |= PCI_STATUS_SIG_TARGET_ABORT;
if (lo & SB_TAR_ERR_FLAG)
conf_data |= PCI_STATUS_REC_TARGET_ABORT;
if (lo & SB_MAR_ERR_FLAG)
conf_data |= PCI_STATUS_REC_MASTER_ABORT;
if (lo & SB_PARE_ERR_FLAG)
conf_data |= PCI_STATUS_DETECTED_PARITY;
break;
case PCI_CLASS_REVISION:
_rdmsr(GLCP_MSR_REG(GLCP_CHIP_REV_ID), &hi, &lo);
conf_data = lo & 0x000000ff;
conf_data |= (CS5536_ISA_CLASS_CODE << 8);
break;
case PCI_CACHE_LINE_SIZE:
_rdmsr(SB_MSR_REG(SB_CTRL), &hi, &lo);
hi &= 0x000000f8;
conf_data = CFG_PCI_CACHE_LINE_SIZE(PCI_BRIDGE_HEADER_TYPE, hi);
break;
/*
* we only use the LBAR of DIVIL, no RCONF used.
* all of them are IO space.
*/
case PCI_BAR0_REG:
return pci_isa_read_bar(0);
break;
case PCI_BAR1_REG:
return pci_isa_read_bar(1);
break;
case PCI_BAR2_REG:
return pci_isa_read_bar(2);
break;
case PCI_BAR3_REG:
break;
case PCI_BAR4_REG:
return pci_isa_read_bar(4);
break;
case PCI_BAR5_REG:
return pci_isa_read_bar(5);
break;
case PCI_CARDBUS_CIS:
conf_data = PCI_CARDBUS_CIS_POINTER;
break;
case PCI_SUBSYSTEM_VENDOR_ID:
conf_data =
CFG_PCI_VENDOR_ID(CS5536_ISA_SUB_ID, CS5536_SUB_VENDOR_ID);
break;
case PCI_ROM_ADDRESS:
conf_data = PCI_EXPANSION_ROM_BAR;
break;
case PCI_CAPABILITY_LIST:
conf_data = PCI_CAPLIST_POINTER;
break;
case PCI_INTERRUPT_LINE:
/* no interrupt used here */
conf_data = CFG_PCI_INTERRUPT_LINE(0x00, 0x00);
break;
default:
break;
}
return conf_data;
}
/*
* isa_write: ISA write transfer
*
* We assume that this is not a bus master transfer.
*/
void pci_isa_write_reg(int reg, u32 value)
{
u32 hi = 0, lo = value;
u32 temp;
switch (reg) {
case PCI_COMMAND:
if (value & PCI_COMMAND_IO)
divil_lbar_enable();
else
divil_lbar_disable();
break;
case PCI_STATUS:
_rdmsr(SB_MSR_REG(SB_ERROR), &hi, &lo);
temp = lo & 0x0000ffff;
if ((value & PCI_STATUS_SIG_TARGET_ABORT) &&
(lo & SB_TAS_ERR_EN))
temp |= SB_TAS_ERR_FLAG;
if ((value & PCI_STATUS_REC_TARGET_ABORT) &&
(lo & SB_TAR_ERR_EN))
temp |= SB_TAR_ERR_FLAG;
if ((value & PCI_STATUS_REC_MASTER_ABORT)
&& (lo & SB_MAR_ERR_EN))
temp |= SB_MAR_ERR_FLAG;
if ((value & PCI_STATUS_DETECTED_PARITY)
&& (lo & SB_PARE_ERR_EN))
temp |= SB_PARE_ERR_FLAG;
lo = temp;
_wrmsr(SB_MSR_REG(SB_ERROR), hi, lo);
break;
case PCI_CACHE_LINE_SIZE:
value &= 0x0000ff00;
_rdmsr(SB_MSR_REG(SB_CTRL), &hi, &lo);
hi &= 0xffffff00;
hi |= (value >> 8);
_wrmsr(SB_MSR_REG(SB_CTRL), hi, lo);
break;
case PCI_BAR0_REG:
pci_isa_write_bar(0, value);
break;
case PCI_BAR1_REG:
pci_isa_write_bar(1, value);
break;
case PCI_BAR2_REG:
pci_isa_write_bar(2, value);
break;
case PCI_BAR3_REG:
pci_isa_write_bar(3, value);
break;
case PCI_BAR4_REG:
pci_isa_write_bar(4, value);
break;
case PCI_BAR5_REG:
pci_isa_write_bar(5, value);
break;
case PCI_UART1_INT_REG:
_rdmsr(DIVIL_MSR_REG(PIC_YSEL_HIGH), &hi, &lo);
/* disable uart1 interrupt in PIC */
lo &= ~(0xf << 24);
if (value) /* enable uart1 interrupt in PIC */
lo |= (CS5536_UART1_INTR << 24);
_wrmsr(DIVIL_MSR_REG(PIC_YSEL_HIGH), hi, lo);
break;
case PCI_UART2_INT_REG:
_rdmsr(DIVIL_MSR_REG(PIC_YSEL_HIGH), &hi, &lo);
/* disable uart2 interrupt in PIC */
lo &= ~(0xf << 28);
if (value) /* enable uart2 interrupt in PIC */
lo |= (CS5536_UART2_INTR << 28);
_wrmsr(DIVIL_MSR_REG(PIC_YSEL_HIGH), hi, lo);
break;
case PCI_ISA_FIXUP_REG:
if (value) {
/* enable the TARGET ABORT/MASTER ABORT etc. */
_rdmsr(SB_MSR_REG(SB_ERROR), &hi, &lo);
lo |= 0x00000063;
_wrmsr(SB_MSR_REG(SB_ERROR), hi, lo);
}
default:
/* ALL OTHER PCI CONFIG SPACE HEADER IS NOT IMPLEMENTED. */
break;
}
}
* Copyright (C) 2009 Lemote, Inc. * Author: Wu Zhangjin, [email protected] * * This program is free software; you can redistribute it and/or modify it * under the terms of the GNU General Public License as published by the * Free Software Foundation; either version 2 of the License, or (at your * option) any later version. */ #include <linux/pci.h> #include <cs5536/cs5536.h> #include <cs5536/cs5536_pci.h> /* common variables for PCI_ISA_READ/WRITE_BAR */ static const u32 divil_msr_reg[6] = { DIVIL_MSR_REG(DIVIL_LBAR_SMB), DIVIL_MSR_REG(DIVIL_LBAR_GPIO), DIVIL_MSR_REG(DIVIL_LBAR_MFGPT), DIVIL_MSR_REG(DIVIL_LBAR_IRQ), DIVIL_MSR_REG(DIVIL_LBAR_PMS), DIVIL_MSR_REG(DIVIL_LBAR_ACPI), }; static const u32 soft_bar_flag[6] = { SOFT_BAR_SMB_FLAG, SOFT_BAR_GPIO_FLAG, SOFT_BAR_MFGPT_FLAG, SOFT_BAR_IRQ_FLAG, SOFT_BAR_PMS_FLAG, SOFT_BAR_ACPI_FLAG, }; static const u32 sb_msr_reg[6] = { SB_MSR_REG(SB_R0), SB_MSR_REG(SB_R1), SB_MSR_REG(SB_R2), SB_MSR_REG(SB_R3), SB_MSR_REG(SB_R4), SB_MSR_REG(SB_R5), }; static const u32 bar_space_range[6] = {
