void DMA_Setup( DMA_CH_t * dmaChannel,
const void * src,
void * dest,
int16_t blockSize,
uint8_t repeatCount )
{
DMA_Enable();
DMA_SetupBlock(
dmaChannel,
src,
DMA_CH_SRCRELOAD_BLOCK_gc,
DMA_CH_SRCDIR_INC_gc,
dest,
DMA_CH_DESTRELOAD_BURST_gc,
DMA_CH_DESTDIR_INC_gc,
blockSize,
DMA_CH_BURSTLEN_2BYTE_gc,
repeatCount,
true
);
// Timer Overflow will trigger DMA
DMA_SetTriggerSource( dmaChannel, 0x40 );
DMA_EnableSingleShot( dmaChannel );
}
/* AsyncMemCopy
*
* Block size 0 = 64k. Enable the DMA channel to use first.
* Then setup channel for copying data, increasing addresses,
* no address pointer reload, with 8-byte bursts.
*
* \note This function is asynchronous and DOES NOT wait for
* completion.This must be handled by the program
* calling this function.
* In this example, an interrupt.
*
*/
void AsyncMemCopy( const void * src,
void * dest,
uint16_t blockSize,
DMA_CH_t * dmaChannel )
{
DMA_EnableChannel( dmaChannel );
DMA_SetupBlock( dmaChannel,
src,
DMA_CH_SRCRELOAD_NONE_gc,
DMA_CH_SRCDIR_INC_gc,
dest,
DMA_CH_DESTRELOAD_NONE_gc,
DMA_CH_DESTDIR_INC_gc,
blockSize,
DMA_CH_BURSTLEN_8BYTE_gc,
0,
false );
DMA_StartTransfer( dmaChannel );
}
bool MemCopy( const void * src, void * dest, uint16_t blockSize,
DMA_CH_t * dmaChannel )
{
uint8_t flags = 0;
DMA_EnableChannel( dmaChannel );
DMA_SetupBlock( dmaChannel,
src,
DMA_CH_SRCRELOAD_NONE_gc,
DMA_CH_SRCDIR_INC_gc,
dest,
DMA_CH_DESTRELOAD_NONE_gc,
DMA_CH_DESTDIR_INC_gc,
blockSize,
DMA_CH_BURSTLEN_8BYTE_gc,
0,
false ); // no repeat
DMA_StartTransfer( dmaChannel );
// Wait until the completion or error flag is set. The flags
// must be cleared manually.
do {
flags = DMA_ReturnStatus_non_blocking( dmaChannel );
} while ( flags == 0 );
// Clear flags
DMA.CH0.CTRLB |= ( flags );
// Check if error flag is set
if ( ( flags & DMA_CH_ERRIF_bm ) != 0x00 )
{
return true;
} else
{
return false;
}
}
/*! \brief Example of a repeated block memory copy operation.
*
* Block size 0 = 64k. Enable the DMA channel to use first and the channel
* will be disabled automatically. A parameter check to avoid illegal values.
* Setup channel for copying data, increasing addresses, no address pointer
* reload, with 8-byte bursts.
*
* \note This function wait until the transfer is complete and use a blocking
* function which also makes this function blocking, hence the function
* will dead-lock if the completion or error flag never get set.
*
* \retval true if success.
* \retval false if failure.
*/
bool MultiBlockMemCopy( const void * src, void * dest, uint16_t blockSize,
uint8_t repeatCount, volatile DMA_CH_t * dmaChannel )
{
uint8_t flags;
DMA_EnableChannel( dmaChannel );
DMA_SetupBlock( dmaChannel,
src,
DMA_CH_SRCRELOAD_NONE_gc,
DMA_CH_SRCDIR_INC_gc,
dest,
DMA_CH_DESTRELOAD_NONE_gc,
DMA_CH_DESTDIR_INC_gc,
blockSize,
DMA_CH_BURSTLEN_8BYTE_gc,
repeatCount,
true );
DMA_StartTransfer( dmaChannel );
/* Wait until the completion or error flag is set. The flags
* must be cleared manually.
*/
do {
flags = DMA_ReturnStatus_non_blocking( dmaChannel );
} while ( flags == 0);
dmaChannel->CTRLB |= ( flags );
/* Check if error flag is set. */
if ( ( flags & DMA_CH_ERRIF_bm ) != 0x00 ) {
return false;
} else {
return true;
}
}
int main(void)
{
facilitatePowersaving();
// Configure switches
PORTCFG.MPCMASK = 0xff; // Configure several PINxCTRL registers at the same time
SWITCHPORT.PIN0CTRL = (SWITCHPORT.PIN0CTRL & ~PORT_OPC_gm) | PORT_OPC_PULLUP_gc; //Enable pull-up to get a defined level on the switches
SWITCHPORT.DIRCLR = 0xff; // Set port as input
// Configure LEDs
PORTCFG.MPCMASK = 0xff; // Configure several PINxCTRL registers at the same time
LEDPORT.PIN0CTRL = PORT_INVEN_bm; // Invert input to turn the leds on when port output value is 1
LEDPORT.DIRSET = 0xff; // Set port as output
LEDPORT.OUT = 0x00; // Set initial value
// Set up ADCB0 on PB0 to read temp sensor. More of this can be achieved by using driver from appnote AVR1300
PORTQ.PIN2CTRL = (PORTQ.PIN2CTRL & ~PORT_OPC_gm) | PORT_OPC_PULLDOWN_gc; // This pin must be grounded to "enable" NTC-resistor
PORTB.DIRCLR = PIN0;
PORTB.PIN0CTRL = (PORTB.PIN0CTRL & ~PORT_OPC_gm);
ADC_CalibrationValues_Load(&ADCB); // Load factory calibration data for ADC
ADCB.CH0.CTRL = (ADCB.CH0.CTRL & ~ADC_CH_INPUTMODE_gm) | ADC_CH_INPUTMODE_SINGLEENDED_gc; // Single ended input
ADCB.CH0.MUXCTRL = (ADCB.CH0.MUXCTRL & ~ADC_CH_MUXPOS_gm) | ADC_CH_MUXPOS_PIN0_gc; // Pin 0 is input
ADCB.REFCTRL = (ADCB.REFCTRL & ~ADC_REFSEL_gm) | ADC_REFSEL_VCC_gc; // Internal AVCC/1.6 as reference
ADCB.CTRLB |= ADC_FREERUN_bm; // Free running mode
ADCB.PRESCALER = (ADCB.PRESCALER & ~ADC_PRESCALER_gm) | ADC_PRESCALER_DIV512_gc; // Divide clock by 1024.
ADCB.CTRLB = (ADCB.CTRLB & ~ADC_RESOLUTION_gm) | ADC_RESOLUTION_8BIT_gc; // Set 8 bit resolution
ADCB.CTRLA |= ADC_ENABLE_bm; // Enable ADC
// Set up DMA CH0 to transfer from ADC to LEDS. We only read low byte.
DMA_Enable();
DMA_SetupBlock(
&DMA.CH0,
(void const *) &(ADCB.CH0RES),
DMA_CH_SRCRELOAD_NONE_gc,
DMA_CH_SRCDIR_FIXED_gc,
(void const *) &(LEDPORT.OUT),
DMA_CH_DESTRELOAD_NONE_gc,
DMA_CH_DESTDIR_FIXED_gc,
1,
DMA_CH_BURSTLEN_1BYTE_gc,
0,
true
);
DMA_EnableSingleShot( &DMA.CH0 );
DMA_SetTriggerSource( &DMA.CH0, DMA_CH_TRIGSRC_ADCB_CH0_gc ); // ADC Channel 0 is trigger source.
// Set up interrupt on button 0, or else we can't come back from IDLE
SWITCHPORT.INTCTRL = (SWITCHPORT.INTCTRL & ~PORT_INT0LVL_gm) | PORT_INT0LVL_LO_gc;
SWITCHPORT.INT0MASK = SWITCHMASK_ACTIVE;
SWITCHPORT.PIN0CTRL = (SWITCHPORT.PIN0CTRL & ~PORT_ISC_gm) | PORT_ISC_FALLING_gc;
// Enable low interrupt level in PMIC and enable global interrupts.
PMIC.CTRL |= PMIC_LOLVLEN_bm;
sei();
// Main loop.
while (1) {
if ((SWITCHPORT.IN & SWITCHMASK_ACTIVE) == 0x00)
{
// Button 0 pressed. Enter ACTIVE mode again.
DMA_DisableChannel( &DMA.CH0 );
SLEEP.CTRL &= ~SLEEP_SEN_bm; // Disable sleep. sleep() is now ineffective.
} else if ((SWITCHPORT.IN & SWITCHMASK_IDLE) == 0x00)
{
// Button 1 pressed. Enter Idle mode
DMA_EnableChannel( &DMA.CH0 );
// Set and enable sleep.
SLEEP.CTRL = (SLEEP.CTRL & ~SLEEP_SMODE_gm) | SLEEP_SMODE_IDLE_gc;
SLEEP.CTRL |= SLEEP_SEN_bm; // Enable sleep.
} else if (SLEEP.CTRL & SLEEP_SEN_bm) {
// We are in wanting-to-sleep mode, but were awake.
sleep();
} else {
// Do active sampling and transfer of ADC data.
LEDPORT.OUT = ADCB.CH0RES & 0xFF;
}
}
}
