static int
write_common(struct ath_hal *ah, const HAL_INI_ARRAY *ia,
HAL_BOOL bChannelChange, int writes)
{
#define IS_NO_RESET_TIMER_ADDR(x) \
( (((x) >= AR_BEACON) && ((x) <= AR_CFP_DUR)) || \
(((x) >= AR_SLEEP1) && ((x) <= AR_SLEEP3)))
#define V(r, c) (ia)->data[((r)*(ia)->cols) + (c)]
int i;
/* Write Common Array Parameters */
for (i = 0; i < ia->rows; i++) {
uint32_t reg = V(i, 0);
/* XXX timer/beacon setup registers? */
/* On channel change, don't reset the PCU registers */
if (!(bChannelChange && IS_NO_RESET_TIMER_ADDR(reg))) {
OS_REG_WRITE(ah, reg, V(i, 1));
DMA_YIELD(writes);
}
}
return writes;
#undef IS_NO_RESET_TIMER_ADDR
#undef V
}
static void
ar9280WriteIni(struct ath_hal *ah, const struct ieee80211_channel *chan)
{
u_int modesIndex, freqIndex;
int regWrites = 0;
int i;
const HAL_INI_ARRAY *ia;
/* Setup the indices for the next set of register array writes */
/* XXX Ignore 11n dynamic mode on the AR5416 for the moment */
if (IEEE80211_IS_CHAN_2GHZ(chan)) {
freqIndex = 2;
if (IEEE80211_IS_CHAN_HT40(chan))
modesIndex = 3;
else if (IEEE80211_IS_CHAN_108G(chan))
modesIndex = 5;
else
modesIndex = 4;
} else {
freqIndex = 1;
if (IEEE80211_IS_CHAN_HT40(chan) ||
IEEE80211_IS_CHAN_TURBO(chan))
modesIndex = 2;
else
modesIndex = 1;
}
/* Set correct Baseband to analog shift setting to access analog chips. */
OS_REG_WRITE(ah, AR_PHY(0), 0x00000007);
OS_REG_WRITE(ah, AR_PHY_ADC_SERIAL_CTL, AR_PHY_SEL_INTERNAL_ADDAC);
/*
* This is unwound because at the moment, there's a requirement
* for Merlin (and later, perhaps) to have a specific bit fixed
* in the AR_AN_TOP2 register before writing it.
*/
ia = &AH5212(ah)->ah_ini_modes;
#if 0
regWrites = ath_hal_ini_write(ah, &AH5212(ah)->ah_ini_modes,
modesIndex, regWrites);
#endif
HALASSERT(modesIndex < ia->cols);
for (i = 0; i < ia->rows; i++) {
uint32_t reg = HAL_INI_VAL(ia, i, 0);
uint32_t val = HAL_INI_VAL(ia, i, modesIndex);
if (reg == AR_AN_TOP2 && AH5416(ah)->ah_need_an_top2_fixup)
val &= ~AR_AN_TOP2_PWDCLKIND;
OS_REG_WRITE(ah, reg, val);
/* Analog shift register delay seems needed for Merlin - PR kern/154220 */
if (reg >= 0x7800 && reg < 0x7900)
OS_DELAY(100);
DMA_YIELD(regWrites);
}
if (AR_SREV_MERLIN_20_OR_LATER(ah)) {
regWrites = ath_hal_ini_write(ah, &AH9280(ah)->ah_ini_rxgain,
modesIndex, regWrites);
regWrites = ath_hal_ini_write(ah, &AH9280(ah)->ah_ini_txgain,
modesIndex, regWrites);
}
/* XXX Merlin 100us delay for shift registers */
regWrites = ath_hal_ini_write(ah, &AH5212(ah)->ah_ini_common,
1, regWrites);
if (AR_SREV_MERLIN_20(ah) && IS_5GHZ_FAST_CLOCK_EN(ah, chan)) {
/* 5GHz channels w/ Fast Clock use different modal values */
regWrites = ath_hal_ini_write(ah, &AH9280(ah)->ah_ini_xmodes,
modesIndex, regWrites);
}
}