static int sh_eth_config(struct sh_eth_dev *eth, bd_t *bd)
{
int port = eth->port, ret = 0;
u32 val, phy_status;
struct sh_eth_info *port_info = ð->port_info[port];
struct eth_device *dev = port_info->dev;
/* Configure e-dmac registers */
outl((inl(EDMR(port)) & ~EMDR_DESC_R) | EDMR_EL, EDMR(port));
outl(0, EESIPR(port));
outl(0, TRSCER(port));
outl(0, TFTR(port));
outl((FIFO_SIZE_T | FIFO_SIZE_R), FDR(port));
outl(RMCR_RST, RMCR(port));
outl(0, RPADIR(port));
outl((FIFO_F_D_RFF | FIFO_F_D_RFD), FCFTR(port));
/* Configure e-mac registers */
outl(0, ECSIPR(port));
/* Set Mac address */
val = dev->enetaddr[0] << 24 | dev->enetaddr[1] << 16 |
dev->enetaddr[2] << 8 | dev->enetaddr[3];
outl(val, MAHR(port));
val = dev->enetaddr[4] << 8 | dev->enetaddr[5];
outl(val, MALR(port));
outl(RFLR_RFL_MIN, RFLR(port));
outl(0, PIPR(port));
outl(APR_AP, APR(port));
outl(MPR_MP, MPR(port));
outl(TPAUSER_TPAUSE, TPAUSER(port));
/* Configure phy */
ret = sh_eth_phy_config(eth);
if (ret) {
printf(SHETHER_NAME ": phy config timeout\n");
goto err_phy_cfg;
}
/* Read phy status to finish configuring the e-mac */
phy_status = sh_eth_mii_read_phy_reg(port, port_info->phy_addr, 1);
/* Set the transfer speed */
if (phy_status & (PHY_S_100X_F|PHY_S_100X_H)) {
printf(SHETHER_NAME ": 100Base/");
outl(GECMR_100B, GECMR(port));
} else {
printf(SHETHER_NAME ": 10Base/");
outl(GECMR_10B, GECMR(port));
}
/* Check if full duplex mode is supported by the phy */
if (phy_status & (PHY_S_100X_F|PHY_S_10T_F)) {
printf("Full\n");
outl((ECMR_CHG_DM|ECMR_RE|ECMR_TE|ECMR_DM), ECMR(port));
} else {
printf("Half\n");
outl((ECMR_CHG_DM|ECMR_RE|ECMR_TE), ECMR(port));
}
return ret;
err_phy_cfg:
return ret;
}
static int sh_eth_config(struct sh_eth_dev *eth, bd_t *bd)
{
int port = eth->port, ret = 0;
u32 val;
struct sh_eth_info *port_info = ð->port_info[port];
struct eth_device *dev = port_info->dev;
struct phy_device *phy;
/* Configure e-dmac registers */
outl((inl(EDMR(port)) & ~EMDR_DESC_R) | EDMR_EL, EDMR(port));
outl(0, EESIPR(port));
outl(0, TRSCER(port));
outl(0, TFTR(port));
outl((FIFO_SIZE_T | FIFO_SIZE_R), FDR(port));
outl(RMCR_RST, RMCR(port));
#if !defined(CONFIG_CPU_SH7757) && !defined(CONFIG_CPU_SH7724)
outl(0, RPADIR(port));
#endif
outl((FIFO_F_D_RFF | FIFO_F_D_RFD), FCFTR(port));
/* Configure e-mac registers */
#if defined(CONFIG_CPU_SH7757)
outl(ECSIPR_BRCRXIP | ECSIPR_PSRTOIP | ECSIPR_LCHNGIP |
ECSIPR_MPDIP | ECSIPR_ICDIP, ECSIPR(port));
#else
outl(0, ECSIPR(port));
#endif
/* Set Mac address */
val = dev->enetaddr[0] << 24 | dev->enetaddr[1] << 16 |
dev->enetaddr[2] << 8 | dev->enetaddr[3];
outl(val, MAHR(port));
val = dev->enetaddr[4] << 8 | dev->enetaddr[5];
outl(val, MALR(port));
outl(RFLR_RFL_MIN, RFLR(port));
#if !defined(CONFIG_CPU_SH7757) && !defined(CONFIG_CPU_SH7724)
outl(0, PIPR(port));
#endif
#if !defined(CONFIG_CPU_SH7724)
outl(APR_AP, APR(port));
outl(MPR_MP, MPR(port));
#endif
#if defined(CONFIG_CPU_SH7763)
outl(TPAUSER_TPAUSE, TPAUSER(port));
#elif defined(CONFIG_CPU_SH7757)
outl(TPAUSER_UNLIMITED, TPAUSER(port));
#endif
/* Configure phy */
ret = sh_eth_phy_config(eth);
if (ret) {
printf(SHETHER_NAME ": phy config timeout\n");
goto err_phy_cfg;
}
phy = port_info->phydev;
phy_startup(phy);
val = 0;
/* Set the transfer speed */
if (phy->speed == 100) {
printf(SHETHER_NAME ": 100Base/");
#ifdef CONFIG_CPU_SH7763
outl(GECMR_100B, GECMR(port));
#elif defined(CONFIG_CPU_SH7757)
outl(1, RTRATE(port));
#elif defined(CONFIG_CPU_SH7724)
val = ECMR_RTM;
#endif
} else if (phy->speed == 10) {
printf(SHETHER_NAME ": 10Base/");
#ifdef CONFIG_CPU_SH7763
outl(GECMR_10B, GECMR(port));
#elif defined(CONFIG_CPU_SH7757)
outl(0, RTRATE(port));
#endif
}
/* Check if full duplex mode is supported by the phy */
if (phy->duplex) {
printf("Full\n");
outl(val | (ECMR_CHG_DM|ECMR_RE|ECMR_TE|ECMR_DM), ECMR(port));
} else {
printf("Half\n");
outl(val | (ECMR_CHG_DM|ECMR_RE|ECMR_TE), ECMR(port));
}
return ret;
err_phy_cfg:
return ret;
}