void lcd_material_reset_defaults()
{
//Fill in the defaults
char buffer[8];
strcpy_P(buffer, PSTR("PLA"));
eeprom_write_block(buffer, EEPROM_MATERIAL_NAME_OFFSET(0), 4);
eeprom_write_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(0), 210);
// eeprom_write_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(0), 60);
eeprom_write_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(0), 100);
eeprom_write_word(EEPROM_MATERIAL_FLOW_OFFSET(0), 100);
eeprom_write_float(EEPROM_MATERIAL_DIAMETER_OFFSET(0), 2.85);
strcpy_P(buffer, PSTR("ABS"));
eeprom_write_block(buffer, EEPROM_MATERIAL_NAME_OFFSET(1), 4);
eeprom_write_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(1), 260);
// eeprom_write_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(1), 90);
eeprom_write_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(1), 50);
eeprom_write_word(EEPROM_MATERIAL_FLOW_OFFSET(1), 107);
eeprom_write_float(EEPROM_MATERIAL_DIAMETER_OFFSET(1), 2.85);
strcpy_P(buffer, PSTR("UPET"));
eeprom_write_block(buffer, EEPROM_MATERIAL_NAME_OFFSET(2), 5);
eeprom_write_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(2), 250);
// eeprom_write_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(2), 60);
eeprom_write_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(2), 50);
eeprom_write_word(EEPROM_MATERIAL_FLOW_OFFSET(2), 100);
eeprom_write_float(EEPROM_MATERIAL_DIAMETER_OFFSET(2), 2.85);
eeprom_write_byte(EEPROM_MATERIAL_COUNT_OFFSET(), 3);
}
void lcd_material_set_material(uint8_t nr, uint8_t e)
{
material[e].temperature = eeprom_read_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(nr));
#if TEMP_SENSOR_BED != 0
material[e].bed_temperature = eeprom_read_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(nr));
#endif
material[e].flow = eeprom_read_word(EEPROM_MATERIAL_FLOW_OFFSET(nr));
material[e].fan_speed = eeprom_read_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(nr));
material[e].diameter = eeprom_read_float(EEPROM_MATERIAL_DIAMETER_OFFSET(nr));
eeprom_read_block(card.longFilename, EEPROM_MATERIAL_NAME_OFFSET(nr), 8);
card.longFilename[8] = '\0';
if (material[e].temperature > HEATER_0_MAXTEMP - 15)
material[e].temperature = HEATER_0_MAXTEMP - 15;
#if TEMP_SENSOR_BED != 0
if (material[e].bed_temperature > BED_MAXTEMP - 15)
material[e].bed_temperature = BED_MAXTEMP - 15;
#endif
material[e].change_temperature = eeprom_read_word(EEPROM_MATERIAL_CHANGE_TEMPERATURE(nr));
material[e].change_preheat_wait_time = eeprom_read_byte(EEPROM_MATERIAL_CHANGE_WAIT_TIME(nr));
if (material[e].change_temperature < 10)
material[e].change_temperature = material[e].temperature;
lcd_material_store_current_material();
}
static void lcd_material_select_details_callback(uint8_t nr)
{
uint8_t count = eeprom_read_byte(EEPROM_MATERIAL_COUNT_OFFSET());
if (nr == 0)
{
}
else if (nr <= count)
{
char buffer[32];
char* c = buffer;
nr -= 1;
if (led_glow_dir)
{
c = float_to_string(eeprom_read_float(EEPROM_MATERIAL_DIAMETER_OFFSET(nr)), c, PSTR("mm"));
while(c < buffer + 10) *c++ = ' ';
strcpy_P(c, PSTR("Flow:"));
c += 5;
c = int_to_string(eeprom_read_word(EEPROM_MATERIAL_FLOW_OFFSET(nr)), c, PSTR("%"));
}else{
c = int_to_string(eeprom_read_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(nr)), c, PSTR("C"));
*c++ = ' ';
c = int_to_string(eeprom_read_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(nr)), c, PSTR("C"));
while(c < buffer + 10) *c++ = ' ';
strcpy_P(c, PSTR("Fan: "));
c += 5;
c = int_to_string(eeprom_read_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(nr)), c, PSTR("%"));
}
lcd_lib_draw_string(5, 53, buffer);
}else{
lcd_lib_draw_string_centerP(53, PSTR("Modify the settings"));
}
}
static void lcd_menu_change_material_select_material_details_callback(uint8_t nr)
{
char buffer[32];
char* c = buffer;
if (led_glow_dir)
{
c = float_to_string(eeprom_read_float(EEPROM_MATERIAL_DIAMETER_OFFSET(nr)), c, PSTR("mm"));
while(c < buffer + 10) *c++ = ' ';
strcpy_P(c, PSTR("Flow:"));
c += 5;
c = int_to_string(eeprom_read_word(EEPROM_MATERIAL_FLOW_OFFSET(nr)), c, PSTR("%"));
}else{
c = int_to_string(eeprom_read_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(nr)), c, PSTR("C"));
#if TEMP_SENSOR_BED != 0
*c++ = ' ';
c = int_to_string(eeprom_read_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(nr)), c, PSTR("C"));
#endif
while(c < buffer + 10) *c++ = ' ';
strcpy_P(c, PSTR("Fan: "));
c += 5;
c = int_to_string(eeprom_read_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(nr)), c, PSTR("%"));
}
lcd_lib_draw_string(5, 53, buffer);
}
void lcd_material_reset_defaults()
{
//Fill in the defaults
SERIAL_ECHO_START;
SERIAL_ECHOLNPGM("Materials reset");
char buffer[MATERIAL_NAME_LENGTH];
for (int a= 0; a< MATERIAL_PRESETS; a++)
{
strncpy_P(buffer, (char PROGMEM *) presets[a].name,MATERIAL_NAME_LENGTH); // this will pad out the whole length with 0 as needed.
eeprom_write_block(buffer , EEPROM_MATERIAL_NAME_OFFSET(a), MATERIAL_NAME_LENGTH);
material_preset temp;
memcpy_P((void*) &temp,&presets[a],sizeof (material_preset));
eeprom_write_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(a) ,temp.temperature);
eeprom_write_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(a),temp.bed);
eeprom_write_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(a) ,temp.fan_speed);
eeprom_write_word(EEPROM_MATERIAL_FLOW_OFFSET(a) ,temp.flow);
eeprom_write_float(EEPROM_MATERIAL_DIAMETER_OFFSET(a) ,temp.diameter);
}
uint8_t e;
for(e=0; e<EXTRUDERS; e++)
{
makeCustomName(e);
strcpy(material_name[e],material_name_buf);
lcd_material_store_current_material();
}
eeprom_write_byte(EEPROM_MATERIAL_COUNT_OFFSET(), MATERIAL_PRESETS);
lcd_lib_beep_ext(500,150);
lcd_lib_beep_ext(750,100);
}
void lcd_material_store_material(uint8_t nr)
{
eeprom_write_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(nr), material[active_extruder].temperature);
eeprom_write_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(nr), material[active_extruder].bed_temperature);
eeprom_write_word(EEPROM_MATERIAL_FLOW_OFFSET(nr), material[active_extruder].flow);
eeprom_write_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(nr), material[active_extruder].fan_speed);
eeprom_write_float(EEPROM_MATERIAL_DIAMETER_OFFSET(nr), material[active_extruder].diameter);
//eeprom_write_block(card.longFilename, EEPROM_MATERIAL_NAME_OFFSET(nr), 8);
}
bool lcd_material_verify_material_settings()
{
bool hasUPET = false;
uint8_t cnt = eeprom_read_byte(EEPROM_MATERIAL_COUNT_OFFSET());
if (cnt < 2 || cnt > EEPROM_MATERIAL_SETTINGS_MAX_COUNT)
return false;
while(cnt > 0)
{
cnt --;
if (eeprom_read_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(cnt)) > HEATER_0_MAXTEMP)
return false;
// if (eeprom_read_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(cnt)) > BED_MAXTEMP)
// return false;
if (eeprom_read_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(cnt)) > 100)
return false;
if (eeprom_read_word(EEPROM_MATERIAL_FLOW_OFFSET(cnt)) > 1000)
return false;
if (eeprom_read_float(EEPROM_MATERIAL_DIAMETER_OFFSET(cnt)) > 10.0)
return false;
if (eeprom_read_float(EEPROM_MATERIAL_DIAMETER_OFFSET(cnt)) < 0.1)
return false;
eeprom_read_block(card.longFilename, EEPROM_MATERIAL_NAME_OFFSET(cnt), 8);
if (strcmp_P(card.longFilename, PSTR("UPET")) == 0)
hasUPET = true;
}
cnt = eeprom_read_byte(EEPROM_MATERIAL_COUNT_OFFSET());
if (!hasUPET && cnt < EEPROM_MATERIAL_SETTINGS_MAX_COUNT)
{
strcpy_P(card.longFilename, PSTR("UPET"));
eeprom_write_block(card.longFilename, EEPROM_MATERIAL_NAME_OFFSET(cnt), 5);
eeprom_write_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(cnt), 250);
// eeprom_write_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(cnt), 60);
eeprom_write_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(cnt), 50);
eeprom_write_word(EEPROM_MATERIAL_FLOW_OFFSET(cnt), 100);
eeprom_write_float(EEPROM_MATERIAL_DIAMETER_OFFSET(cnt), 2.85);
eeprom_write_byte(EEPROM_MATERIAL_COUNT_OFFSET(), cnt + 1);
}
return true;
}
void lcd_material_store_current_material()
{
for(uint8_t e=0; e<EXTRUDERS; e++)
{
eeprom_write_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e), material[e].temperature);
eeprom_write_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e), material[e].bed_temperature);
eeprom_write_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e), material[e].fan_speed);
eeprom_write_word(EEPROM_MATERIAL_FLOW_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e), material[e].flow);
eeprom_write_float(EEPROM_MATERIAL_DIAMETER_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e), material[e].diameter);
}
}
void lcd_material_read_current_material()
{
for(uint8_t e=0; e<EXTRUDERS; e++)
{
material[e].temperature = eeprom_read_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e));
material[e].bed_temperature = eeprom_read_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e));
material[e].flow = eeprom_read_word(EEPROM_MATERIAL_FLOW_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e));
material[e].fan_speed = eeprom_read_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e));
material[e].diameter = eeprom_read_float(EEPROM_MATERIAL_DIAMETER_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e));
}
}
void lcd_material_store_material(uint8_t nr)
{
eeprom_write_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(nr), material[active_extruder].temperature);
#if TEMP_SENSOR_BED != 0
eeprom_write_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(nr), material[active_extruder].bed_temperature);
#endif
eeprom_write_word(EEPROM_MATERIAL_FLOW_OFFSET(nr), material[active_extruder].flow);
eeprom_write_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(nr), material[active_extruder].fan_speed);
eeprom_write_float(EEPROM_MATERIAL_DIAMETER_OFFSET(nr), material[active_extruder].diameter);
//eeprom_write_block(card.longFilename, EEPROM_MATERIAL_NAME_OFFSET(nr), 8);
eeprom_write_word(EEPROM_MATERIAL_CHANGE_TEMPERATURE(nr), material[active_extruder].change_temperature);
eeprom_write_byte(EEPROM_MATERIAL_CHANGE_WAIT_TIME(nr), material[active_extruder].change_preheat_wait_time);
}
void lcd_material_store_current_material()
{
for(uint8_t e=0; e<EXTRUDERS; e++)
{
eeprom_write_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e), material[e].temperature);
#if TEMP_SENSOR_BED != 0
eeprom_write_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e), material[e].bed_temperature);
#endif
eeprom_write_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e), material[e].fan_speed);
eeprom_write_word(EEPROM_MATERIAL_FLOW_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e), material[e].flow);
eeprom_write_float(EEPROM_MATERIAL_DIAMETER_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e), material[e].diameter);
eeprom_write_word(EEPROM_MATERIAL_CHANGE_TEMPERATURE(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e), material[e].change_temperature);
eeprom_write_byte(EEPROM_MATERIAL_CHANGE_WAIT_TIME(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e), material[e].change_preheat_wait_time);
}
}
void lcd_material_read_current_material()
{
for(uint8_t e=0; e<EXTRUDERS; e++)
{
material[e].temperature = eeprom_read_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e));
material[e].bed_temperature = eeprom_read_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e));
material[e].flow = eeprom_read_word(EEPROM_MATERIAL_FLOW_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e));
material[e].fan_speed = eeprom_read_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e));
material[e].diameter = eeprom_read_float(EEPROM_MATERIAL_DIAMETER_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e));
strcpy_P(material_name[e],PSTR("???"));
eeprom_read_block(material_name[e], EEPROM_MATERIAL_NAME_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e), MATERIAL_NAME_LENGTH);
material_name[e][MATERIAL_NAME_LENGTH] = '\0';
}
}
void lcd_material_set_material(uint8_t nr, uint8_t e)
{
material[e].temperature = eeprom_read_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(nr));
material[e].bed_temperature = eeprom_read_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(nr));
material[e].flow = eeprom_read_word(EEPROM_MATERIAL_FLOW_OFFSET(nr));
material[e].fan_speed = eeprom_read_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(nr));
material[e].diameter = eeprom_read_float(EEPROM_MATERIAL_DIAMETER_OFFSET(nr));
eeprom_read_block(card.longFilename, EEPROM_MATERIAL_NAME_OFFSET(nr), 8);
card.longFilename[8] = '\0';
if (material[e].temperature > HEATER_0_MAXTEMP - 15)
material[e].temperature = HEATER_0_MAXTEMP - 15;
if (material[e].bed_temperature > BED_MAXTEMP - 15)
material[e].bed_temperature = BED_MAXTEMP - 15;
lcd_material_store_current_material();
}
bool lcd_material_verify_material_settings()
{
SERIAL_ECHO_START;
uint8_t max_mats = eeprom_read_byte(EEPROM_MATERIAL_COUNT_OFFSET());
SERIAL_ECHOPAIR("Checking ", (unsigned long) max_mats);
SERIAL_ECHOPAIR(" presets and ", (unsigned long) EXTRUDERS);
SERIAL_ECHOLNPGM (" extruder settings:");
if (max_mats < 2 || max_mats > EEPROM_MATERIAL_SETTINGS_MAX_COUNT)
return false;
byte cnt =0;
while(cnt < max_mats+EXTRUDERS)
{
SERIAL_ECHOPAIR("Checking preset # ",(unsigned long) cnt);
if (eeprom_read_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(cnt)) > HEATER_0_MAXTEMP)
return false;
if (eeprom_read_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(cnt)) > BED_MAXTEMP)
return false;
if (eeprom_read_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(cnt)) > 100)
return false;
if (eeprom_read_word(EEPROM_MATERIAL_FLOW_OFFSET(cnt)) > 1000)
return false;
if (eeprom_read_float(EEPROM_MATERIAL_DIAMETER_OFFSET(cnt)) > 10.0)
return false;
if (eeprom_read_float(EEPROM_MATERIAL_DIAMETER_OFFSET(cnt)) < 0.1)
return false;
strcpy_P (material_name_buf,"???");
eeprom_read_block(material_name_buf, EEPROM_MATERIAL_NAME_OFFSET(cnt), MATERIAL_NAME_LENGTH);
material_name_buf[MATERIAL_NAME_LENGTH] = '\0';
if (cnt >= max_mats )
{ SERIAL_ECHOPAIR(".....verified extruder setting # ",(unsigned long) cnt-max_mats);}
else
{ SERIAL_ECHOPAIR(".....verified preset # ",(unsigned long) cnt);}
SERIAL_ECHO(" (");
SERIAL_ECHO(material_name_buf);
SERIAL_ECHO(")");
SERIAL_ECHOLN("");
cnt++;
}
return true;
}
void lcd_material_read_current_material()
{
for(uint8_t e=0; e<EXTRUDERS; e++)
{
material[e].temperature = eeprom_read_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e));
#if TEMP_SENSOR_BED != 0
material[e].bed_temperature = eeprom_read_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e));
#endif
material[e].flow = eeprom_read_word(EEPROM_MATERIAL_FLOW_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e));
material[e].fan_speed = eeprom_read_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e));
material[e].diameter = eeprom_read_float(EEPROM_MATERIAL_DIAMETER_OFFSET(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e));
material[e].change_temperature = eeprom_read_word(EEPROM_MATERIAL_CHANGE_TEMPERATURE(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e));
material[e].change_preheat_wait_time = eeprom_read_byte(EEPROM_MATERIAL_CHANGE_WAIT_TIME(EEPROM_MATERIAL_SETTINGS_MAX_COUNT+e));
if (material[e].change_temperature < 10)
material[e].change_temperature = material[e].temperature;
}
}
bool lcd_material_verify_material_settings()
{
uint8_t cnt = eeprom_read_byte(EEPROM_MATERIAL_COUNT_OFFSET());
if (cnt < 2 || cnt > 16)
return false;
while(cnt > 0)
{
cnt --;
if (eeprom_read_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(cnt)) > HEATER_0_MAXTEMP)
return false;
if (eeprom_read_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(cnt)) > BED_MAXTEMP)
return false;
if (eeprom_read_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(cnt)) > 100)
return false;
if (eeprom_read_word(EEPROM_MATERIAL_FLOW_OFFSET(cnt)) > 1000)
return false;
if (eeprom_read_float(EEPROM_MATERIAL_DIAMETER_OFFSET(cnt)) > 10.0)
return false;
if (eeprom_read_float(EEPROM_MATERIAL_DIAMETER_OFFSET(cnt)) < 0.1)
return false;
}
return true;
}
static void lcd_menu_material_export()
{
if (!card.sdInserted)
{
LED_GLOW();
lcd_lib_encoder_pos = MAIN_MENU_ITEM_POS(0);
lcd_info_screen(lcd_menu_material_select);
lcd_lib_draw_string_centerP(15, PSTR("No SD-CARD!"));
lcd_lib_draw_string_centerP(25, PSTR("Please insert card"));
lcd_lib_update_screen();
card.release();
return;
}
if (!card.isOk())
{
lcd_info_screen(lcd_menu_material_select);
lcd_lib_draw_string_centerP(16, PSTR("Reading card..."));
lcd_lib_update_screen();
card.initsd();
return;
}
card.setroot();
card.openFile("MATERIAL.TXT", false);
uint8_t count = eeprom_read_byte(EEPROM_MATERIAL_COUNT_OFFSET());
for(uint8_t n=0; n<count; n++)
{
char buffer[32];
strcpy_P(buffer, PSTR("[material]\n"));
card.write_string(buffer);
strcpy_P(buffer, PSTR("name="));
char* ptr = buffer + strlen(buffer);
eeprom_read_block(ptr, EEPROM_MATERIAL_NAME_OFFSET(n), 8);
ptr[8] = '\0';
strcat_P(buffer, PSTR("\n"));
card.write_string(buffer);
strcpy_P(buffer, PSTR("temperature="));
ptr = buffer + strlen(buffer);
int_to_string(eeprom_read_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(n)), ptr, PSTR("\n"));
card.write_string(buffer);
#if TEMP_SENSOR_BED != 0
strcpy_P(buffer, PSTR("bed_temperature="));
ptr = buffer + strlen(buffer);
int_to_string(eeprom_read_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(n)), ptr, PSTR("\n"));
card.write_string(buffer);
#endif
strcpy_P(buffer, PSTR("fan_speed="));
ptr = buffer + strlen(buffer);
int_to_string(eeprom_read_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(n)), ptr, PSTR("\n"));
card.write_string(buffer);
strcpy_P(buffer, PSTR("flow="));
ptr = buffer + strlen(buffer);
int_to_string(eeprom_read_word(EEPROM_MATERIAL_FLOW_OFFSET(n)), ptr, PSTR("\n"));
card.write_string(buffer);
strcpy_P(buffer, PSTR("diameter="));
ptr = buffer + strlen(buffer);
float_to_string(eeprom_read_float(EEPROM_MATERIAL_DIAMETER_OFFSET(n)), ptr, PSTR("\n\n"));
card.write_string(buffer);
#ifdef USE_CHANGE_TEMPERATURE
strcpy_P(buffer, PSTR("change_temp="));
ptr = buffer + strlen(buffer);
float_to_string(eeprom_read_word(EEPROM_MATERIAL_CHANGE_TEMPERATURE(n)), ptr, PSTR("\n\n"));
card.write_string(buffer);
strcpy_P(buffer, PSTR("change_wait="));
ptr = buffer + strlen(buffer);
float_to_string(eeprom_read_byte(EEPROM_MATERIAL_CHANGE_WAIT_TIME(n)), ptr, PSTR("\n\n"));
card.write_string(buffer);
#endif
}
card.closefile();
currentMenu = lcd_menu_material_export_done;
}
static void lcd_menu_material_import()
{
if (!card.sdInserted)
{
LED_GLOW();
lcd_lib_encoder_pos = MAIN_MENU_ITEM_POS(0);
lcd_info_screen(lcd_menu_material_select);
lcd_lib_draw_string_centerP(15, PSTR("No SD-CARD!"));
lcd_lib_draw_string_centerP(25, PSTR("Please insert card"));
lcd_lib_update_screen();
card.release();
return;
}
if (!card.isOk())
{
lcd_info_screen(lcd_menu_material_select);
lcd_lib_draw_string_centerP(16, PSTR("Reading card..."));
lcd_lib_update_screen();
card.initsd();
return;
}
card.setroot();
card.openFile("MATERIAL.TXT", true);
if (!card.isFileOpen())
{
lcd_info_screen(lcd_menu_material_select);
lcd_lib_draw_string_centerP(15, PSTR("No export file"));
lcd_lib_draw_string_centerP(25, PSTR("Found on card."));
lcd_lib_update_screen();
return;
}
char buffer[32];
uint8_t count = 0xFF;
while(card.fgets(buffer, sizeof(buffer)) > 0)
{
buffer[sizeof(buffer)-1] = '\0';
char* c = strchr(buffer, '\n');
if (c) *c = '\0';
if(strcmp_P(buffer, PSTR("[material]")) == 0)
{
count++;
}else if (count < EEPROM_MATERIAL_SETTINGS_MAX_COUNT)
{
c = strchr(buffer, '=');
if (c)
{
*c++ = '\0';
if (strcmp_P(buffer, PSTR("name")) == 0)
{
eeprom_write_block(c, EEPROM_MATERIAL_NAME_OFFSET(count), 8);
}else if (strcmp_P(buffer, PSTR("temperature")) == 0)
{
eeprom_write_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(count), strtol(c, NULL, 10));
}else if (strcmp_P(buffer, PSTR("bed_temperature")) == 0)
{
eeprom_write_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(count), strtol(c, NULL, 10));
}else if (strcmp_P(buffer, PSTR("fan_speed")) == 0)
{
eeprom_write_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(count), strtol(c, NULL, 10));
}else if (strcmp_P(buffer, PSTR("flow")) == 0)
{
eeprom_write_word(EEPROM_MATERIAL_FLOW_OFFSET(count), strtol(c, NULL, 10));
}else if (strcmp_P(buffer, PSTR("diameter")) == 0)
{
eeprom_write_float(EEPROM_MATERIAL_DIAMETER_OFFSET(count), strtod(c, NULL));
#ifdef USE_CHANGE_TEMPERATURE
}else if (strcmp_P(buffer, PSTR("change_temp")) == 0)
{
eeprom_write_word(EEPROM_MATERIAL_CHANGE_TEMPERATURE(count), strtol(c, NULL, 10));
}else if (strcmp_P(buffer, PSTR("change_wait")) == 0)
{
eeprom_write_byte(EEPROM_MATERIAL_CHANGE_WAIT_TIME(count), strtol(c, NULL, 10));
#endif
}
}
}
}
count++;
if (count > 0)
{
eeprom_write_byte(EEPROM_MATERIAL_COUNT_OFFSET(), count);
}
card.closefile();
currentMenu = lcd_menu_material_import_done;
}
bool lcd_material_verify_material_settings()
{
bool hasCPE = false;
uint8_t cnt = eeprom_read_byte(EEPROM_MATERIAL_COUNT_OFFSET());
if (cnt < 2 || cnt > EEPROM_MATERIAL_SETTINGS_MAX_COUNT)
return false;
while(cnt > 0)
{
cnt --;
if (eeprom_read_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(cnt)) > HEATER_0_MAXTEMP)
return false;
#if TEMP_SENSOR_BED != 0
if (eeprom_read_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(cnt)) > BED_MAXTEMP)
return false;
#endif
if (eeprom_read_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(cnt)) > 100)
return false;
if (eeprom_read_word(EEPROM_MATERIAL_FLOW_OFFSET(cnt)) > 1000)
return false;
if (eeprom_read_float(EEPROM_MATERIAL_DIAMETER_OFFSET(cnt)) > 10.0)
return false;
if (eeprom_read_float(EEPROM_MATERIAL_DIAMETER_OFFSET(cnt)) < 0.1)
return false;
eeprom_read_block(card.longFilename, EEPROM_MATERIAL_NAME_OFFSET(cnt), 8);
if (strcmp_P(card.longFilename, PSTR("UPET")) == 0)
{
strcpy_P(card.longFilename, PSTR("CPE"));
eeprom_write_block(card.longFilename, EEPROM_MATERIAL_NAME_OFFSET(cnt), 4);
}
if (strcmp_P(card.longFilename, PSTR("CPE")) == 0)
{
hasCPE = true;
}
if (eeprom_read_word(EEPROM_MATERIAL_CHANGE_TEMPERATURE(cnt)) > HEATER_0_MAXTEMP || eeprom_read_word(EEPROM_MATERIAL_CHANGE_TEMPERATURE(cnt)) < 10)
{
//Invalid temperature for change temperature.
eeprom_write_word(EEPROM_MATERIAL_CHANGE_TEMPERATURE(cnt), eeprom_read_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(cnt)));
eeprom_write_byte(EEPROM_MATERIAL_CHANGE_WAIT_TIME(cnt), 0);
}
}
cnt = eeprom_read_byte(EEPROM_MATERIAL_COUNT_OFFSET());
if (!hasCPE && cnt < EEPROM_MATERIAL_SETTINGS_MAX_COUNT)
{
strcpy_P(card.longFilename, PSTR("CPE"));
eeprom_write_block(card.longFilename, EEPROM_MATERIAL_NAME_OFFSET(cnt), 4);
eeprom_write_word(EEPROM_MATERIAL_TEMPERATURE_OFFSET(cnt), 250);
eeprom_write_word(EEPROM_MATERIAL_BED_TEMPERATURE_OFFSET(cnt), 60);
eeprom_write_byte(EEPROM_MATERIAL_FAN_SPEED_OFFSET(cnt), 50);
eeprom_write_word(EEPROM_MATERIAL_FLOW_OFFSET(cnt), 100);
eeprom_write_float(EEPROM_MATERIAL_DIAMETER_OFFSET(cnt), 2.85);
eeprom_write_word(EEPROM_MATERIAL_CHANGE_TEMPERATURE(cnt), 250);
eeprom_write_byte(EEPROM_MATERIAL_CHANGE_WAIT_TIME(cnt), 0);
eeprom_write_byte(EEPROM_MATERIAL_COUNT_OFFSET(), cnt + 1);
}
return true;
}
