/**
* ixgbe_reset_phy_generic - Performs a PHY reset
* @hw: pointer to hardware structure
**/
s32 ixgbe_reset_phy_generic(struct ixgbe_hw *hw)
{
u32 i;
u16 ctrl = 0;
s32 status = 0;
if (hw->phy.type == ixgbe_phy_unknown)
status = ixgbe_identify_phy_generic(hw);
if (status != 0 || hw->phy.type == ixgbe_phy_none)
goto out;
/* Don't reset PHY if it's shut down due to overtemp. */
if (!hw->phy.reset_if_overtemp &&
(IXGBE_ERR_OVERTEMP == hw->phy.ops.check_overtemp(hw)))
goto out;
/*
* Perform soft PHY reset to the PHY_XS.
* This will cause a soft reset to the PHY
*/
hw->phy.ops.write_reg(hw, IXGBE_MDIO_PHY_XS_CONTROL,
IXGBE_MDIO_PHY_XS_DEV_TYPE,
IXGBE_MDIO_PHY_XS_RESET);
/*
* Poll for reset bit to self-clear indicating reset is complete.
* Some PHYs could take up to 3 seconds to complete and need about
* 1.7 usec delay after the reset is complete.
*/
for (i = 0; i < 30; i++) {
msleep(100);
hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_XS_CONTROL,
IXGBE_MDIO_PHY_XS_DEV_TYPE, &ctrl);
if (!(ctrl & IXGBE_MDIO_PHY_XS_RESET)) {
udelay(2);
break;
}
}
if (ctrl & IXGBE_MDIO_PHY_XS_RESET) {
status = IXGBE_ERR_RESET_FAILED;
ERROR_REPORT1(IXGBE_ERROR_POLLING,
"PHY reset polling failed to complete.\n");
}
out:
return status;
}
/**
* ixgbe_identify_phy_generic - Get physical layer module
* @hw: pointer to hardware structure
*
* Determines the physical layer module found on the current adapter.
**/
s32 ixgbe_identify_phy_generic(struct ixgbe_hw *hw)
{
s32 status = IXGBE_ERR_PHY_ADDR_INVALID;
u32 phy_addr;
u16 ext_ability = 0;
if (hw->phy.type == ixgbe_phy_unknown) {
for (phy_addr = 0; phy_addr < IXGBE_MAX_PHY_ADDR; phy_addr++) {
if (ixgbe_validate_phy_addr(hw, phy_addr)) {
hw->phy.addr = phy_addr;
ixgbe_get_phy_id(hw);
hw->phy.type =
ixgbe_get_phy_type_from_id(hw->phy.id);
if (hw->phy.type == ixgbe_phy_unknown) {
hw->phy.ops.read_reg(hw,
IXGBE_MDIO_PHY_EXT_ABILITY,
IXGBE_MDIO_PMA_PMD_DEV_TYPE,
&ext_ability);
if (ext_ability &
(IXGBE_MDIO_PHY_10GBASET_ABILITY |
IXGBE_MDIO_PHY_1000BASET_ABILITY))
hw->phy.type =
ixgbe_phy_cu_unknown;
else
hw->phy.type =
ixgbe_phy_generic;
}
status = 0;
break;
}
}
/* clear value if nothing found */
if (status != 0) {
hw->phy.addr = 0;
ERROR_REPORT1(IXGBE_ERROR_INVALID_STATE,
"Could not identify valid PHY address");
}
} else {
status = 0;
}
return status;
}
/**
* ixgbe_reset_hw_X540 - Perform hardware reset
* @hw: pointer to hardware structure
*
* Resets the hardware by resetting the transmit and receive units, masks
* and clears all interrupts, and perform a reset.
**/
s32 ixgbe_reset_hw_X540(struct ixgbe_hw *hw)
{
s32 status;
u32 ctrl, i;
DEBUGFUNC("ixgbe_reset_hw_X540");
/* Call adapter stop to disable tx/rx and clear interrupts */
status = hw->mac.ops.stop_adapter(hw);
if (status != IXGBE_SUCCESS)
goto reset_hw_out;
/* flush pending Tx transactions */
ixgbe_clear_tx_pending(hw);
mac_reset_top:
ctrl = IXGBE_CTRL_RST;
ctrl |= IXGBE_READ_REG(hw, IXGBE_CTRL);
IXGBE_WRITE_REG(hw, IXGBE_CTRL, ctrl);
IXGBE_WRITE_FLUSH(hw);
/* Poll for reset bit to self-clear indicating reset is complete */
for (i = 0; i < 10; i++) {
usec_delay(1);
ctrl = IXGBE_READ_REG(hw, IXGBE_CTRL);
if (!(ctrl & IXGBE_CTRL_RST_MASK))
break;
}
if (ctrl & IXGBE_CTRL_RST_MASK) {
status = IXGBE_ERR_RESET_FAILED;
ERROR_REPORT1(IXGBE_ERROR_POLLING,
"Reset polling failed to complete.\n");
}
msec_delay(100);
/*
* Double resets are required for recovery from certain error
* conditions. Between resets, it is necessary to stall to allow time
* for any pending HW events to complete.
*/
if (hw->mac.flags & IXGBE_FLAGS_DOUBLE_RESET_REQUIRED) {
hw->mac.flags &= ~IXGBE_FLAGS_DOUBLE_RESET_REQUIRED;
goto mac_reset_top;
}
/* Set the Rx packet buffer size. */
IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(0), 384 << IXGBE_RXPBSIZE_SHIFT);
/* Store the permanent mac address */
hw->mac.ops.get_mac_addr(hw, hw->mac.perm_addr);
/*
* Store MAC address from RAR0, clear receive address registers, and
* clear the multicast table. Also reset num_rar_entries to 128,
* since we modify this value when programming the SAN MAC address.
*/
hw->mac.num_rar_entries = 128;
hw->mac.ops.init_rx_addrs(hw);
/* Store the permanent SAN mac address */
hw->mac.ops.get_san_mac_addr(hw, hw->mac.san_addr);
/* Add the SAN MAC address to the RAR only if it's a valid address */
if (ixgbe_validate_mac_addr(hw->mac.san_addr) == 0) {
hw->mac.ops.set_rar(hw, hw->mac.num_rar_entries - 1,
hw->mac.san_addr, 0, IXGBE_RAH_AV);
/* Save the SAN MAC RAR index */
hw->mac.san_mac_rar_index = hw->mac.num_rar_entries - 1;
/* Reserve the last RAR for the SAN MAC address */
hw->mac.num_rar_entries--;
}
/* Store the alternative WWNN/WWPN prefix */
hw->mac.ops.get_wwn_prefix(hw, &hw->mac.wwnn_prefix,
&hw->mac.wwpn_prefix);
reset_hw_out:
return status;
}
/**
* ixgbe_read_phy_reg_generic - Reads a value from a specified PHY register
* @hw: pointer to hardware structure
* @reg_addr: 32 bit address of PHY register to read
* @phy_data: Pointer to read data from PHY register
**/
s32 ixgbe_read_phy_reg_generic(struct ixgbe_hw *hw, u32 reg_addr,
u32 device_type, u16 *phy_data)
{
u32 command;
u32 i;
u32 data;
s32 status = 0;
u16 gssr;
if (IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_LAN_ID_1)
gssr = IXGBE_GSSR_PHY1_SM;
else
gssr = IXGBE_GSSR_PHY0_SM;
if (hw->mac.ops.acquire_swfw_sync(hw, gssr) != 0)
status = IXGBE_ERR_SWFW_SYNC;
if (status == 0) {
/* Setup and write the address cycle command */
command = ((reg_addr << IXGBE_MSCA_NP_ADDR_SHIFT) |
(device_type << IXGBE_MSCA_DEV_TYPE_SHIFT) |
(hw->phy.addr << IXGBE_MSCA_PHY_ADDR_SHIFT) |
(IXGBE_MSCA_ADDR_CYCLE | IXGBE_MSCA_MDI_COMMAND));
IXGBE_WRITE_REG(hw, IXGBE_MSCA, command);
/*
* Check every 10 usec to see if the address cycle completed.
* The MDI Command bit will clear when the operation is
* complete
*/
for (i = 0; i < IXGBE_MDIO_COMMAND_TIMEOUT; i++) {
udelay(10);
command = IXGBE_READ_REG(hw, IXGBE_MSCA);
if ((command & IXGBE_MSCA_MDI_COMMAND) == 0)
break;
}
if ((command & IXGBE_MSCA_MDI_COMMAND) != 0) {
ERROR_REPORT1(IXGBE_ERROR_POLLING,
"PHY address command did not complete.\n");
status = IXGBE_ERR_PHY;
}
if (status == 0) {
/*
* Address cycle complete, setup and write the read
* command
*/
command = ((reg_addr << IXGBE_MSCA_NP_ADDR_SHIFT) |
(device_type << IXGBE_MSCA_DEV_TYPE_SHIFT) |
(hw->phy.addr << IXGBE_MSCA_PHY_ADDR_SHIFT) |
(IXGBE_MSCA_READ | IXGBE_MSCA_MDI_COMMAND));
IXGBE_WRITE_REG(hw, IXGBE_MSCA, command);
/*
* Check every 10 usec to see if the address cycle
* completed. The MDI Command bit will clear when the
* operation is complete
*/
for (i = 0; i < IXGBE_MDIO_COMMAND_TIMEOUT; i++) {
udelay(10);
command = IXGBE_READ_REG(hw, IXGBE_MSCA);
if ((command & IXGBE_MSCA_MDI_COMMAND) == 0)
break;
}
if ((command & IXGBE_MSCA_MDI_COMMAND) != 0) {
ERROR_REPORT1(IXGBE_ERROR_POLLING,
"PHY read command didn't complete\n");
status = IXGBE_ERR_PHY;
} else {
/*
* Read operation is complete. Get the data
* from MSRWD
*/
data = IXGBE_READ_REG(hw, IXGBE_MSRWD);
data >>= IXGBE_MSRWD_READ_DATA_SHIFT;
*phy_data = (u16)(data);
}
}
