/**
* @brief Program option bytes
* @param pOBInit: pointer to an FLASH_OBInitStruct structure that
* contains the configuration information for the programming.
*
* @retval HAL Status
*/
HAL_StatusTypeDef HAL_FLASHEx_OBProgram(FLASH_OBProgramInitTypeDef *pOBInit)
{
HAL_StatusTypeDef status = HAL_ERROR;
/* Process Locked */
__HAL_LOCK(&pFlash);
/* Check the parameters */
assert_param(IS_OPTIONBYTE(pOBInit->OptionType));
/*Write protection configuration*/
if((pOBInit->OptionType & OPTIONBYTE_WRP) == OPTIONBYTE_WRP)
{
assert_param(IS_WRPSTATE(pOBInit->WRPState));
if(pOBInit->WRPState == OB_WRPSTATE_ENABLE)
{
/*Enable of Write protection on the selected Sector*/
status = FLASH_OB_EnableWRP(pOBInit->WRPSector, pOBInit->Banks);
}
else
{
/*Disable of Write protection on the selected Sector*/
status = FLASH_OB_DisableWRP(pOBInit->WRPSector, pOBInit->Banks);
}
}
/*Read protection configuration*/
if((pOBInit->OptionType & OPTIONBYTE_RDP) == OPTIONBYTE_RDP)
{
status = FLASH_OB_RDP_LevelConfig(pOBInit->RDPLevel);
}
/*USER configuration*/
if((pOBInit->OptionType & OPTIONBYTE_USER) == OPTIONBYTE_USER)
{
status = FLASH_OB_UserConfig(pOBInit->USERConfig&OB_IWDG_SW,
pOBInit->USERConfig&OB_STOP_NO_RST,
pOBInit->USERConfig&OB_STDBY_NO_RST);
}
/*BOR Level configuration*/
if((pOBInit->OptionType & OPTIONBYTE_BOR) == OPTIONBYTE_BOR)
{
status = FLASH_OB_BOR_LevelConfig(pOBInit->BORLevel);
}
/* Process Unlocked */
__HAL_UNLOCK(&pFlash);
return status;
}
/**
* @brief Program option bytes
* @note The function HAL_FLASH_Unlock() should be called before to unlock the FLASH interface
* The function HAL_FLASH_OB_Unlock() should be called before to unlock the options bytes
* The function HAL_FLASH_OB_Launch() should be called after to force the reload of the options bytes
* (system reset will occur)
*
* @param pOBInit: pointer to an FLASH_OBInitStruct structure that
* contains the configuration information for the programming.
*
* @retval HAL_StatusTypeDef HAL Status
*/
HAL_StatusTypeDef HAL_FLASHEx_OBProgram(FLASH_OBProgramInitTypeDef *pOBInit)
{
HAL_StatusTypeDef status = HAL_ERROR;
/* Check the parameters */
assert_param(IS_OPTIONBYTE(pOBInit->OptionType));
/* Write protection configuration */
if((pOBInit->OptionType & OPTIONBYTE_WRP) == OPTIONBYTE_WRP)
{
assert_param(IS_WRPSTATE(pOBInit->WRPState));
if (pOBInit->WRPState == OB_WRPSTATE_ENABLE)
{
/* Enable of Write protection on the selected page */
status = FLASH_OB_EnableWRP(pOBInit->WRPPage);
}
else
{
/* Disable of Write protection on the selected page */
status = FLASH_OB_DisableWRP(pOBInit->WRPPage);
}
}
/* Read protection configuration */
if((pOBInit->OptionType & OPTIONBYTE_RDP) == OPTIONBYTE_RDP)
{
status = FLASH_OB_RDP_LevelConfig(pOBInit->RDPLevel);
}
/* USER configuration */
if((pOBInit->OptionType & OPTIONBYTE_USER) == OPTIONBYTE_USER)
{
status = FLASH_OB_UserConfig(pOBInit->USERConfig);
}
/* DATA configuration*/
if((pOBInit->OptionType & OPTIONBYTE_DATA) == OPTIONBYTE_DATA)
{
status = FLASH_OB_ProgramData(pOBInit->DATAAddress, pOBInit->DATAData);
}
return status;
}
/**
* @brief Program option bytes
* @param pOBInit pointer to an FLASH_OBInitStruct structure that
* contains the configuration information for the programming.
*
* @retval HAL Status
*/
HAL_StatusTypeDef HAL_FLASHEx_OBProgram(FLASH_OBProgramInitTypeDef *pOBInit)
{
HAL_StatusTypeDef status = HAL_OK;
/* Process Locked */
__HAL_LOCK(&pFlash);
/* Check the parameters */
assert_param(IS_OPTIONBYTE(pOBInit->OptionType));
pFlash.ErrorCode = HAL_FLASH_ERROR_NONE;
/*Write protection configuration*/
if((pOBInit->OptionType & OPTIONBYTE_WRP) == OPTIONBYTE_WRP)
{
assert_param(IS_WRPSTATE(pOBInit->WRPState));
assert_param(IS_FLASH_BANK(pOBInit->Banks));
if(pOBInit->WRPState == OB_WRPSTATE_ENABLE)
{
/*Enable of Write protection on the selected Sector*/
status = FLASH_OB_EnableWRP(pOBInit->WRPSector,pOBInit->Banks);
}
else
{
/*Disable of Write protection on the selected Sector*/
status = FLASH_OB_DisableWRP(pOBInit->WRPSector, pOBInit->Banks);
}
if(status != HAL_OK)
{
/* Process Unlocked */
__HAL_UNLOCK(&pFlash);
return status;
}
}
/* Read protection configuration */
if((pOBInit->OptionType & OPTIONBYTE_RDP) != RESET)
{
/* Configure the Read protection level */
status = FLASH_OB_RDPConfig(pOBInit->RDPLevel);
if(status != HAL_OK)
{
/* Process Unlocked */
__HAL_UNLOCK(&pFlash);
return status;
}
}
/* User Configuration */
if((pOBInit->OptionType & OPTIONBYTE_USER) != RESET)
{
/* Configure the user option bytes */
status = FLASH_OB_UserConfig(pOBInit->USERType, pOBInit->USERConfig);
if(status != HAL_OK)
{
/* Process Unlocked */
__HAL_UNLOCK(&pFlash);
return status;
}
}
/* PCROP Configuration */
if((pOBInit->OptionType & OPTIONBYTE_PCROP) != RESET)
{
assert_param(IS_FLASH_BANK(pOBInit->Banks));
/*Configure the Proprietary code readout protection */
status = FLASH_OB_PCROPConfig(pOBInit->PCROPConfig, pOBInit->PCROPStartAddr, pOBInit->PCROPEndAddr, pOBInit->Banks);
if(status != HAL_OK)
{
/* Process Unlocked */
__HAL_UNLOCK(&pFlash);
return status;
}
}
/*BOR Level configuration*/
if((pOBInit->OptionType & OPTIONBYTE_BOR) == OPTIONBYTE_BOR)
{
status = FLASH_OB_BOR_LevelConfig(pOBInit->BORLevel);
if(status != HAL_OK)
{
/* Process Unlocked */
__HAL_UNLOCK(&pFlash);
return status;
}
}
/*Boot Address configuration*/
if((pOBInit->OptionType & OPTIONBYTE_BOOTADD) == OPTIONBYTE_BOOTADD)
{
status = FLASH_OB_BootAddConfig(pOBInit->BootConfig, pOBInit->BootAddr0, pOBInit->BootAddr1);
if(status != HAL_OK)
{
/* Process Unlocked */
__HAL_UNLOCK(&pFlash);
return status;
}
}
/*Bank1 secure area configuration*/
if((pOBInit->OptionType & OPTIONBYTE_SECURE_AREA) == OPTIONBYTE_SECURE_AREA)
{
status = FLASH_OB_SecureAreaConfig(pOBInit->SecureAreaConfig, pOBInit->SecureAreaStartAddr, pOBInit->SecureAreaEndAddr,pOBInit->Banks);
if(status != HAL_OK)
{
/* Process Unlocked */
__HAL_UNLOCK(&pFlash);
return status;
}
}
/* Process Unlocked */
__HAL_UNLOCK(&pFlash);
return status;
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32l1xx_xx.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32l1xx.c file
*/
/* Set the vector table address */
#if defined(BOOT_FROM_BANK1)
/* Set the vector table to the Bank1 start address */
NVIC_SetVectorTable(NVIC_VectTab_FLASH, BANK1_START_ADDRESS);
#elif defined(BOOT_FROM_BANK2)
/* Set the vector table to the Bank1 start address */
NVIC_SetVectorTable(NVIC_VectTab_FLASH, BANK2_START_ADDRESS);
#endif /* BOOT_FROM_BANK1 */
/* Initialize LEDs, Buttons and LCD on STM32L152D-EVAL board ****************/
STM_EVAL_LEDInit(LED1);
STM_EVAL_LEDInit(LED2);
STM_EVAL_LEDInit(LED3);
STM_EVAL_LEDInit(LED4);
/* Save the first BANK1 page */
FLASH_SaveBANK1();
/* Save the first BANK2 page */
FLASH_SaveBANK2();
/* SysTick end of count event each 10ms */
RCC_GetClocksFreq(&RCC_Clocks);
SysTick_Config(RCC_Clocks.HCLK_Frequency / 100);
/* Configure the Joystick buttons */
STM_EVAL_PBInit(BUTTON_UP, BUTTON_MODE_GPIO);
STM_EVAL_PBInit(BUTTON_SEL, BUTTON_MODE_GPIO);
STM_EVAL_PBInit(BUTTON_DOWN, BUTTON_MODE_GPIO);
STM_EVAL_PBInit(BUTTON_RIGHT, BUTTON_MODE_GPIO);
STM_EVAL_PBInit(BUTTON_LEFT, BUTTON_MODE_GPIO);
/* Initialize the LCD */
STM32L152D_LCD_Init();
/* Display message on STM32L152D-EVAL LCD ************************************/
/* Clear the LCD */
LCD_Clear(LCD_COLOR_WHITE);
/* Set the LCD Back Color */
#if defined(BOOT_FROM_BANK1)
LCD_SetBackColor(LCD_COLOR_BLUE);
#elif defined(BOOT_FROM_BANK2)
LCD_SetBackColor(LCD_COLOR_RED);
#endif /* BOOT_FROM_BANK1 */
/* Set the LCD Text Color */
LCD_SetTextColor(LCD_COLOR_WHITE);
LCD_DisplayStringLine(LCD_LINE_0, MESSAGE1);
LCD_DisplayStringLine(LCD_LINE_1, MESSAGE2);
LCD_DisplayStringLine(LCD_LINE_2, MESSAGE3);
LCD_DisplayStringLine(LCD_LINE_4, MESSAGE4);
LCD_SetFont(&Font12x12);
LCD_SetTextColor(LCD_COLOR_GREEN);
LCD_DisplayStringLine(LCD_LINE_10, MESSAGE5);
LCD_DisplayStringLine(LCD_LINE_11, MESSAGE6);
LCD_SetTextColor(LCD_COLOR_WHITE);
LCD_DisplayStringLine(LCD_LINE_12, MESSAGE7);
LCD_DisplayStringLine(LCD_LINE_13, MESSAGE8);
LCD_SetTextColor(LCD_COLOR_GREEN);
LCD_DisplayStringLine(LCD_LINE_14, MESSAGE9);
LCD_DisplayStringLine(LCD_LINE_15, MESSAGE10);
LCD_SetTextColor(LCD_COLOR_WHITE);
LCD_DisplayStringLine(LCD_LINE_16, MESSAGE11);
LCD_DisplayStringLine(LCD_LINE_17, MESSAGE12);
LCD_SetTextColor(LCD_COLOR_GREEN);
LCD_DisplayStringLine(LCD_LINE_18, MESSAGE13);
LCD_DisplayStringLine(LCD_LINE_19, MESSAGE14);
LCD_SetTextColor(LCD_COLOR_WHITE);
LCD_SetFont(&Font16x24);
/* Turn on leds available on STM32L152D-EVAL ************************************/
STM_EVAL_LEDOn(LED1);
STM_EVAL_LEDOn(LED2);
STM_EVAL_LEDOn(LED3);
STM_EVAL_LEDOn(LED4);
/* Infinite loop */
while (1)
{
/*--- If Joystick DOWN button is pushed, reset BFB2 bit to enable boot from Bank2
(active after next reset, w/ Boot pins set in Boot from Flash memory position ---*/
if (STM_EVAL_PBGetState(BUTTON_DOWN) == 0)
{
/* Reset BFB2 bit to enable boot from Flash Bank2 */
FLASH_Unlock();
FLASH_OB_Unlock();
FLASH_ClearFlag(FLASH_FLAG_EOP|FLASH_FLAG_WRPERR | FLASH_FLAG_PGAERR |
FLASH_FLAG_SIZERR | FLASH_FLAG_OPTVERR | FLASH_FLAG_OPTVERRUSR);
FLASH_OB_UserConfig(OB_IWDG_SW, OB_STOP_NoRST, OB_STDBY_NoRST);
FLASH_OB_BORConfig(OB_BOR_LEVEL1);
if (FLASH_OB_BootConfig(OB_BOOT_BANK2) == FLASH_COMPLETE)
{
/* Generate System Reset to load the new option byte values */
FLASH_OB_Launch();
}
else
{
/* Display information */
LCD_DisplayStringLine(LCD_LINE_6, MESSAGE15);
}
}
/*--- If Joystick UP button is pushed, set BFB2 bit to enable boot from Bank1
(active after next reset, w/ Boot pins set in Boot from Flash memory position ---*/
if (STM_EVAL_PBGetState(BUTTON_UP) == 0)
{
/* Set BFB2 bit to enable boot from Flash Bank2 */
FLASH_Unlock();
FLASH_OB_Unlock();
FLASH_ClearFlag(FLASH_FLAG_EOP|FLASH_FLAG_WRPERR | FLASH_FLAG_PGAERR |
FLASH_FLAG_SIZERR | FLASH_FLAG_OPTVERR | FLASH_FLAG_OPTVERRUSR);
FLASH_OB_UserConfig(OB_IWDG_SW, OB_STOP_NoRST, OB_STDBY_NoRST);
FLASH_OB_BORConfig(OB_BOR_LEVEL1);
if (FLASH_OB_BootConfig(OB_BOOT_BANK1) == FLASH_COMPLETE)
{
/* Generate System Reset to load the new option byte values */
FLASH_OB_Launch();
}
else
{
/* Display information */
LCD_DisplayStringLine(LCD_LINE_6, MESSAGE15);
}
}
/*--- If Joystick LEFT button is pushed, program the content of address 0x08000000
(base address of Bank1) to 0x00 ---*/
if (STM_EVAL_PBGetState(BUTTON_LEFT) == 0)
{
FLASH_Unlock();
FLASH_ClearFlag(FLASH_FLAG_EOP | FLASH_FLAG_WRPERR | FLASH_FLAG_PGAERR |
FLASH_FLAG_SIZERR | FLASH_FLAG_OPTVERR | FLASH_FLAG_OPTVERRUSR);
/* Erase stack pointer value at Bank 1 start address */
FLASH_ErasePage(0x08000000);
FLASH_Lock();
LCD_ClearLine(LCD_LINE_5);
LCD_ClearLine(LCD_LINE_7);
LCD_ClearLine(LCD_LINE_8);
LCD_ClearLine(LCD_LINE_9);
/* Check if erase operation is OK */
if ((uint32_t)(*(uint32_t *)BANK1_START_ADDRESS) != 0x00)
{
/* Display information */
LCD_DisplayStringLine(LCD_LINE_6, MESSAGE15);
}
else
{
/* Display information */
LCD_DisplayStringLine(LCD_LINE_6, MESSAGE16);
}
}
/*--- If Joystick RIGHT button is pushed, program the content of address 0x08030000
(base address of Bank2) to 0x00 ---*/
if (STM_EVAL_PBGetState(BUTTON_RIGHT) == 0)
{
FLASH_Unlock();
FLASH_ClearFlag(FLASH_FLAG_EOP|FLASH_FLAG_WRPERR | FLASH_FLAG_PGAERR |
FLASH_FLAG_SIZERR | FLASH_FLAG_OPTVERR | FLASH_FLAG_OPTVERRUSR);
/* Erase stack pointer value at Bank 2 start address */
FLASH_ErasePage(0x08030000);
FLASH_Lock();
LCD_ClearLine(LCD_LINE_5);
LCD_ClearLine(LCD_LINE_7);
LCD_ClearLine(LCD_LINE_8);
LCD_ClearLine(LCD_LINE_9);
/* Check if erase operation is OK */
if ((uint32_t)(*(uint32_t *)BANK2_START_ADDRESS) != 0x00)
{
/* Display information */
LCD_DisplayStringLine(LCD_LINE_6, MESSAGE15);
}
else
{
/* Display information */
LCD_DisplayStringLine(LCD_LINE_6, MESSAGE16);
}
}
/*--- If Joystick UP button is pushed, copy the program to the cross bank --*/
if (STM_EVAL_PBGetState(BUTTON_SEL) == 0)
{
FLASH_Unlock();
FLASH_ClearFlag(FLASH_FLAG_EOP|FLASH_FLAG_WRPERR | FLASH_FLAG_PGAERR |
FLASH_FLAG_SIZERR | FLASH_FLAG_OPTVERR | FLASH_FLAG_OPTVERRUSR);
#if defined (BOOT_FROM_BANK1)
/* Erase one page in BANK2 to store the first page */
FLASH_ErasePage(0x08030000);
for(index = 0; index < 64; index++)
{
FLASH_FastProgramWord((0x08030000 + (index * 4)), (*(uint32_t *)(0x08020000 + (index * 4))));
}
#elif defined (BOOT_FROM_BANK2)
/* Erase one page in BANK1 to store the first page */
FLASH_ErasePage(0x08000000);
for(index = 0; index < 64; index++)
{
FLASH_FastProgramWord((0x08000000 + (index * 4)), (*(uint32_t *)(0x08050000 + (index * 4))));
}
#endif
}
/* Toggle LD3 */
STM_EVAL_LEDToggle(LED3);
/* Insert 50 ms delay */
Delay(5);
/* Toggle LD2 */
STM_EVAL_LEDToggle(LED2);
/* Insert 100 ms delay */
Delay(10);
}
}
