/**
* @brief To select HSI as System clock source
* @caller ADC_Icc_Test
* @param None
* @retval None
*/
void SetHSICLK(void)
{
/* Enable HSI Clock */
RCC_HSICmd(ENABLE);
/*!< Wait till HSI is ready */
while (RCC_GetFlagStatus(RCC_FLAG_HSIRDY) == RESET);
/* Enable 64-bit access */
FLASH_ReadAccess64Cmd(ENABLE);
/* Enable Prefetch Buffer */
FLASH_PrefetchBufferCmd(ENABLE);
/* Flash 1 wait state */
FLASH_SetLatency(FLASH_Latency_1);
RCC_SYSCLKConfig(RCC_SYSCLKSource_HSI);
while (RCC_GetSYSCLKSource() != 0x04);
RCC_HCLKConfig(RCC_SYSCLK_Div1);
/* PCLK2 = HCLK */
RCC_PCLK2Config(RCC_HCLK_Div1);
/* PCLK1 = HCLK */
RCC_PCLK1Config(RCC_HCLK_Div1);
}
/**
* @brief Selects HSE as System clock source and configure HCLK, PCLK2 and PCLK1 prescalers.
* @param None
* @retval None
*/
void SetHCLKTo8(void)
{
/* SYSCLK, HCLK, PCLK2 and PCLK1 configuration -----------------------------*/
/* RCC system reset(for debug purpose) */
RCC_DeInit();
/* Enable HSE */
RCC_HSEConfig(RCC_HSE_ON);
/* Wait till HSE is ready */
HSEStartUpStatus = RCC_WaitForHSEStartUp();
if (HSEStartUpStatus == SUCCESS)
{
/* Flash 0 wait state */
FLASH_SetLatency(FLASH_Latency_0);
/* Disable Prefetch Buffer */
FLASH_PrefetchBufferCmd(DISABLE);
/* Disable 64-bit access */
FLASH_ReadAccess64Cmd(DISABLE);
/* Enable the PWR APB1 Clock */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);
/* Select the Voltage Range 2 (1.5V) */
PWR_VoltageScalingConfig(PWR_VoltageScaling_Range2);
/* Wait Until the Voltage Regulator is ready */
while (PWR_GetFlagStatus(PWR_FLAG_VOS) != RESET)
{}
/* HCLK = SYSCLK */
RCC_HCLKConfig(RCC_SYSCLK_Div1);
/* PCLK2 = HCLK */
RCC_PCLK2Config(RCC_HCLK_Div1);
/* PCLK1 = HCLK */
RCC_PCLK1Config(RCC_HCLK_Div1);
/* Select HSE as system clock source */
RCC_SYSCLKConfig(RCC_SYSCLKSource_HSE);
/* Wait till HSE is used as system clock source */
while (RCC_GetSYSCLKSource() != 0x08)
{}
}
else
{ /* If HSE fails to start-up, the application will have wrong clock configuration.
User can add here some code to deal with this error */
/* Go to infinite loop */
while (1)
{}
}
}
/**
* @brief To select MSI as System clock source
* @caller ADC_Icc_Test
* @param Frequence, DIV by 2 ot not , With or without RTC
* @retval None
*/
void SetHSICLKToMSI(uint32_t freq,bool div2,bool With_RTC)
{
/* RCC system reset */
RCC_DeInit();
/* Flash 1 wait state */
FLASH_SetLatency(FLASH_Latency_0);
/* Disable Prefetch Buffer */
FLASH_PrefetchBufferCmd(DISABLE);
/* Disable 64-bit access */
FLASH_ReadAccess64Cmd(DISABLE);
/* Disable FLASH during SLeep */
FLASH_SLEEPPowerDownCmd(ENABLE);
/* Enable the PWR APB1 Clock */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);
/* Select the Voltage Range 3 (1.2V) */
PWR_VoltageScalingConfig(PWR_VoltageScaling_Range3);
/* Wait Until the Voltage Regulator is ready */
while (PWR_GetFlagStatus(PWR_FLAG_VOS) != RESET)
{}
/* To configure the MSI frequency */
RCC_MSIRangeConfig(freq);
/* Select MSI as system clock source */
RCC_SYSCLKConfig(RCC_SYSCLKSource_MSI);
/* Wait till MSI is used as system clock source */
while (RCC_GetSYSCLKSource() != 0x00)
{}
if (div2)
{
RCC_HCLKConfig(RCC_SYSCLK_Div2);
}
RCC_HSICmd(DISABLE);
/* Disable HSE clock */
RCC_HSEConfig(RCC_HSE_OFF);
/* Disable LSE clock */
if (! With_RTC)
RCC_LSEConfig(RCC_LSE_OFF);
/* Disable LSI clock */
RCC_LSICmd(DISABLE);
}
void initPowerSubsystem() {
RCC_MSIRangeConfig(RCC_MSIRange_4);
new_power_state = POWER_STATE_MED_SPEED;
currentCPU_HZ = powerStateClockFrequency(new_power_state);
SysTick_Config(powerStateClockFrequency(new_power_state) / configTICK_RATE_HZ);
current_power_state = new_power_state;
PWR_VoltageScalingConfig(PWR_VoltageScaling_Range3);
FLASH_SetLatency(FLASH_Latency_0);
FLASH_PrefetchBufferCmd(DISABLE);
FLASH_ReadAccess64Cmd(DISABLE);
}
/**
* @brief Selects MSI (64KHz) as System clock source and configure
* HCLK, PCLK2 and PCLK1 prescalers.
* @param None
* @retval None
*/
void SetHCLKToMSI_64KHz(void)
{
/* RCC system reset */
RCC_DeInit();
/* Flash 0 wait state */
FLASH_SetLatency(FLASH_Latency_0);
/* Disable Prefetch Buffer */
FLASH_PrefetchBufferCmd(DISABLE);
/* Disable 64-bit access */
FLASH_ReadAccess64Cmd(DISABLE);
/* Enable the PWR APB1 Clock */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);
/* Select the Voltage Range 3 (1.2V) */
PWR_VoltageScalingConfig(PWR_VoltageScaling_Range3);
/* Wait Until the Voltage Regulator is ready */
while (PWR_GetFlagStatus(PWR_FLAG_VOS) != RESET)
{}
/* HCLK = SYSCLK */
RCC_HCLKConfig(RCC_SYSCLK_Div1);
/* PCLK2 = HCLK */
RCC_PCLK2Config(RCC_HCLK_Div1);
/* PCLK1 = HCLK */
RCC_PCLK1Config(RCC_HCLK_Div1);
/* Set MSI clock range to 64KHz */
RCC_MSIRangeConfig(RCC_MSIRange_0);
/* Select MSI as system clock source */
RCC_SYSCLKConfig(RCC_SYSCLKSource_MSI);
/* Wait till PLL is used as system clock source */
while (RCC_GetSYSCLKSource() != 0x00)
{}
}
/**
* @brief Selects MSI (Default Value, 2MHz) as System clock source and configure
* HCLK, PCLK2 and PCLK1 prescalers.
* @param None
* @retval None
*/
void SetHCLKToMSI_2MHz(void)
{
/* RCC system reset */
RCC_DeInit();
/* Flash 0 wait state */
FLASH_SetLatency(FLASH_Latency_0);
/* Disable Prefetch Buffer */
FLASH_PrefetchBufferCmd(DISABLE);
/* Disable 64-bit access */
FLASH_ReadAccess64Cmd(DISABLE);
/* Enable the PWR APB1 Clock */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);
/* Select the Voltage Range 3 (1.2V) */
PWR_VoltageScalingConfig(PWR_VoltageScaling_Range3);
/* Wait Until the Voltage Regulator is ready */
while (PWR_GetFlagStatus(PWR_FLAG_VOS) != RESET)
{}
}
/**
* @brief Selects HSI as System clock source and configure HCLK, PCLK2 and PCLK1 prescalers.
* @param None
* @retval None
*/
void SetHCLKToHSI(void)
{
__IO uint32_t StartUpCounter = 0, HSIStatus = 0;
/* SYSCLK, HCLK, PCLK2 and PCLK1 configuration -----------------------------*/
/* RCC system reset(for debug purpose) */
RCC_DeInit();
/* Enable HSI */
RCC_HSICmd(ENABLE);
/* Wait till HSI is ready and if Time out is reached exit */
do
{
HSIStatus = RCC_GetFlagStatus(RCC_FLAG_HSIRDY);
StartUpCounter++;
}
while ((HSIStatus == 0) && (StartUpCounter != HSI_STARTUP_TIMEOUT));
if (RCC_GetFlagStatus(RCC_FLAG_HSIRDY) != RESET)
{
HSIStatus = (uint32_t)0x01;
}
else
{
HSIStatus = (uint32_t)0x00;
}
if (HSIStatus == 0x01)
{
/* Flash 0 wait state */
FLASH_SetLatency(FLASH_Latency_0);
/* Disable Prefetch Buffer */
FLASH_PrefetchBufferCmd(DISABLE);
/* Disable 64-bit access */
FLASH_ReadAccess64Cmd(DISABLE);
/* Enable the PWR APB1 Clock */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);
/* Select the Voltage Range 1 (1.8V) */
PWR_VoltageScalingConfig(PWR_VoltageScaling_Range1);
/* Wait Until the Voltage Regulator is ready */
while (PWR_GetFlagStatus(PWR_FLAG_VOS) != RESET)
{}
/* HCLK = SYSCLK */
RCC_HCLKConfig(RCC_SYSCLK_Div1);
/* PCLK2 = HCLK */
RCC_PCLK2Config(RCC_HCLK_Div1);
/* PCLK1 = HCLK */
RCC_PCLK1Config(RCC_HCLK_Div1);
/* Select HSI as system clock source */
RCC_SYSCLKConfig(RCC_SYSCLKSource_HSI);
/* Wait till HSI is used as system clock source */
while (RCC_GetSYSCLKSource() != 0x04)
{}
}
else
{ /* If HSI fails to start-up, the application will have wrong clock configuration.
User can add here some code to deal with this error */
/* Go to infinite loop */
while (1)
{}
}
}
/**
* @brief This function configures the system to enter Low Power Run mode for
* current consumption measurement purpose.
* The maximum clock when the system is in Low Power Run mode is ~128KHz.
* This mode can only be entered when Voltage Range 2 is selected.
* Low Power Run Mode from SRAM:
* =============================
* - System Running at MSI (~32KHz)
* - Flash 0 wait state
* - Voltage Range 2
* - Code running from Internal SRAM
* - All peripherals OFF
* - FLASH switched OFF
* - VDD from 1.65V to 3.6V
* - Current Consumption ~10.5uA
* - Wakeup using Key Button PA.00
* Low Power Run Mode from FLASH:
* ==============================
* - System Running at MSI (~32KHz)
* - Flash 0 wait state
* - Voltage Range 2
* - Code running from Internal FLASH
* - All peripherals OFF
* - VDD from 1.65V to 3.6V
* - Current Consumption ~25uA
* - Wakeup using Key Button PA.00
* @param None
* @retval None
*/
void LowPowerRunMode_Measure(void)
{
/* Configure the System Clock to MSI Range 0 (65KHz). ----------------------*/
/* RCC system reset */
RCC_DeInit();
/* Flash 0 wait state */
FLASH_SetLatency(FLASH_Latency_0);
/* Disable Prefetch Buffer */
FLASH_PrefetchBufferCmd(DISABLE);
/* Disable 64-bit access */
FLASH_ReadAccess64Cmd(DISABLE);
/* Enable the PWR APB1 Clock */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);
/* Select the Voltage Range 2 (1.5V) */
PWR_VoltageScalingConfig(PWR_VoltageScaling_Range2);
/* Wait Until the Voltage Regulator is ready */
while(PWR_GetFlagStatus(PWR_FLAG_VOS) != RESET)
{
}
/* HCLK = SYSCLK/2 = ~32KHz */
RCC_HCLKConfig(RCC_SYSCLK_Div2);
/* PCLK2 = HCLK */
RCC_PCLK2Config(RCC_HCLK_Div1);
/* PCLK1 = HCLK */
RCC_PCLK1Config(RCC_HCLK_Div1);
/* Set MSI clock range to 65.536KHz */
RCC_MSIRangeConfig(RCC_MSIRange_0);
/* Select MSI as system clock source */
RCC_SYSCLKConfig(RCC_SYSCLKSource_MSI);
/* Wait till PLL is used as system clock source */
while (RCC_GetSYSCLKSource() != 0x00)
{}
/* Configure all GPIO as analog to reduce current consumption on non used IOs */
/* Enable GPIOs clock */
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA | RCC_AHBPeriph_GPIOB | RCC_AHBPeriph_GPIOC |
RCC_AHBPeriph_GPIOD | RCC_AHBPeriph_GPIOE | RCC_AHBPeriph_GPIOH |
RCC_AHBPeriph_GPIOF | RCC_AHBPeriph_GPIOG, ENABLE);
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_40MHz;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_All;
GPIO_Init(GPIOC, &GPIO_InitStructure);
GPIO_Init(GPIOD, &GPIO_InitStructure);
GPIO_Init(GPIOE, &GPIO_InitStructure);
GPIO_Init(GPIOH, &GPIO_InitStructure);
GPIO_Init(GPIOF, &GPIO_InitStructure);
GPIO_Init(GPIOG, &GPIO_InitStructure);
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_Init(GPIOB, &GPIO_InitStructure);
/* Disable GPIOs clock */
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA | RCC_AHBPeriph_GPIOB | RCC_AHBPeriph_GPIOC |
RCC_AHBPeriph_GPIOD | RCC_AHBPeriph_GPIOE | RCC_AHBPeriph_GPIOH |
RCC_AHBPeriph_GPIOF | RCC_AHBPeriph_GPIOG, DISABLE);
/* Configure Key Button*/
STM_EVAL_PBInit(BUTTON_KEY,BUTTON_MODE_GPIO);
/* Wait Until Key button pressed */
while(STM_EVAL_PBGetState(BUTTON_KEY) == RESET)
{
}
/* Wait Until Key button pressed */
while(STM_EVAL_PBGetState(BUTTON_KEY) != RESET)
{
}
/* Enter RUN LP Mode */
PWR_EnterLowPowerRunMode(ENABLE);
/* Wait until the system enters RUN LP and the Regulator is in LP mode */
while(PWR_GetFlagStatus(PWR_FLAG_REGLP) == RESET)
{
}
/* Jump to Internal SRAM and Switch the internal FLASH OFF */
#if defined (LP_RUN_SRAM_MODE)
LowPowerRunModeSRAM_Measure();
#elif defined (LP_RUN_FLASH_MODE)
/* Wait Until Key button pressed */
while(STM_EVAL_PBGetState(BUTTON_KEY) == RESET)
{
}
/* Wait Until Key button pressed */
while(STM_EVAL_PBGetState(BUTTON_KEY) != RESET)
{
}
#endif
/* Exit the RUN LP Mode */
PWR_EnterLowPowerRunMode(DISABLE);
/* Wait until the system exits RUN LP and the Regulator is in main mode */
while(PWR_GetFlagStatus(PWR_FLAG_REGLP) != RESET)
{
}
/* Infinite loop */
while (1)
{
}
}
/**
* @brief This function configures the system to enter Low Power Sleep mode for
* current consumption measurement purpose.
* The maximum clock when the system is in Low Power Run mode is ~128KHz.
* This mode can only be entered when Voltage Range 2 is selected.
* Low Power Sleep Mode
* ====================
* - System Running at MSI (~32KHz)
* - Flash 0 wait state
* - Voltage Range 2
* - Code running from Internal FLASH
* - All peripherals OFF
* - VDD from 1.65V to 3.6V
* - Current Consumption ~4.07uA
* - Wakeup using EXTI Line (Key Button PA.00)
* @param None
* @retval None
*/
void LowPowerSleepMode_Measure(void)
{
/* Configure the System Clock to MSI Range 0 (65KHz). ----------------------*/
/* RCC system reset */
RCC_DeInit();
/* Flash 0 wait state */
FLASH_SetLatency(FLASH_Latency_0);
/* Disable Prefetch Buffer */
FLASH_PrefetchBufferCmd(DISABLE);
/* Disable 64-bit access */
FLASH_ReadAccess64Cmd(DISABLE);
/* Enable the PWR APB1 Clock */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);
/* Select the Voltage Range 2 (1.5V) */
PWR_VoltageScalingConfig(PWR_VoltageScaling_Range2);
/* Wait Until the Voltage Regulator is ready */
while(PWR_GetFlagStatus(PWR_FLAG_VOS) != RESET)
{
}
/* HCLK = SYSCLK/2 = ~32KHz */
RCC_HCLKConfig(RCC_SYSCLK_Div2);
/* PCLK2 = HCLK */
RCC_PCLK2Config(RCC_HCLK_Div1);
/* PCLK1 = HCLK */
RCC_PCLK1Config(RCC_HCLK_Div1);
/* Set MSI clock range to 65.536KHz */
RCC_MSIRangeConfig(RCC_MSIRange_0);
/* Select MSI as system clock source */
RCC_SYSCLKConfig(RCC_SYSCLKSource_MSI);
/* Wait till PLL is used as system clock source */
while (RCC_GetSYSCLKSource() != 0x00)
{}
/* Configure all GPIO as analog to reduce current consumption on non used IOs */
/* Enable GPIOs clock */
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA | RCC_AHBPeriph_GPIOB | RCC_AHBPeriph_GPIOC |
RCC_AHBPeriph_GPIOD | RCC_AHBPeriph_GPIOE | RCC_AHBPeriph_GPIOH |
RCC_AHBPeriph_GPIOF | RCC_AHBPeriph_GPIOG, ENABLE);
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_40MHz;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_All;
GPIO_Init(GPIOC, &GPIO_InitStructure);
GPIO_Init(GPIOD, &GPIO_InitStructure);
GPIO_Init(GPIOE, &GPIO_InitStructure);
GPIO_Init(GPIOH, &GPIO_InitStructure);
GPIO_Init(GPIOF, &GPIO_InitStructure);
GPIO_Init(GPIOG, &GPIO_InitStructure);
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_Init(GPIOB, &GPIO_InitStructure);
/* Disable GPIOs clock */
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA | RCC_AHBPeriph_GPIOB | RCC_AHBPeriph_GPIOC |
RCC_AHBPeriph_GPIOD | RCC_AHBPeriph_GPIOE | RCC_AHBPeriph_GPIOH |
RCC_AHBPeriph_GPIOF | RCC_AHBPeriph_GPIOG, DISABLE);
/* Configure Key Button*/
STM_EVAL_PBInit(BUTTON_KEY,BUTTON_MODE_GPIO);
/* Wait Until Key button pressed */
while(STM_EVAL_PBGetState(BUTTON_KEY) == RESET)
{
}
/* Wait Until Key button pressed */
while(STM_EVAL_PBGetState(BUTTON_KEY) != RESET)
{
}
/* Configure Key Button*/
STM_EVAL_PBInit(BUTTON_KEY,BUTTON_MODE_EXTI);
/* Enable The ultra Low Power Mode */
PWR_UltraLowPowerCmd(ENABLE);
/* Enable the power down mode during Sleep mode */
FLASH_SLEEPPowerDownCmd(ENABLE);
/* Request to enter SLEEP mode with regulator in low power mode */
PWR_EnterSleepMode(PWR_Regulator_LowPower, PWR_SLEEPEntry_WFI);
/* Initialize LED1 on STM32L152-EVAL board */
STM_EVAL_LEDInit(LED1);
/* Infinite loop */
while (1)
{
/* Toggle The LED1 */
STM_EVAL_LEDToggle(LED1);
/* Inserted Delay */
for(index = 0; index < 0x5FF; index++);
}
}
/**
* @brief This function configures the system to enter Sleep mode for
* current consumption measurement purpose.
* Sleep Mode
* ==========
* - System Running at HSI (16MHz)
* - Flash 1 wait state
* - Voltage Range 2
* - Code running from Internal FLASH
* - Current Consumption ~1mA
* - Wakeup using EXTI Line (Key Button PA.00)
* @param None
* @retval None
*/
void SleepMode_Measure(void)
{
/* Configure System Clock to HSI (16MHz) */
__IO uint32_t StartUpCounter = 0, HSIStatus = 0;
/* SYSCLK, HCLK, PCLK2 and PCLK1 configuration -----------------------------*/
/* RCC system reset(for debug purpose) */
RCC_DeInit();
/* Enable HSI */
RCC_HSICmd(ENABLE);
/* Wait till HSI is ready and if Time out is reached exit */
do
{
HSIStatus = RCC_GetFlagStatus(RCC_FLAG_HSIRDY);
StartUpCounter++;
} while((HSIStatus == 0) && (StartUpCounter != HSI_STARTUP_TIMEOUT));
if (RCC_GetFlagStatus(RCC_FLAG_HSIRDY) != RESET)
{
HSIStatus = (uint32_t)0x01;
}
else
{
HSIStatus = (uint32_t)0x00;
}
if (HSIStatus == 0x01)
{
/* Enable 64-bit access */
FLASH_ReadAccess64Cmd(ENABLE);
/* Enable Prefetch Buffer */
FLASH_PrefetchBufferCmd(ENABLE);
/* Flash 1 wait state */
FLASH_SetLatency(FLASH_Latency_1);
/* Enable the PWR APB1 Clock */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);
/* Select the Voltage Range 2 (1.5V) */
PWR_VoltageScalingConfig(PWR_VoltageScaling_Range2);
/* Wait Until the Voltage Regulator is ready */
while(PWR_GetFlagStatus(PWR_FLAG_VOS) != RESET)
{
}
/* HCLK = SYSCLK */
RCC_HCLKConfig(RCC_SYSCLK_Div1);
/* PCLK2 = HCLK */
RCC_PCLK2Config(RCC_HCLK_Div1);
/* PCLK1 = HCLK */
RCC_PCLK1Config(RCC_HCLK_Div1);
/* Select HSI as system clock source */
RCC_SYSCLKConfig(RCC_SYSCLKSource_HSI);
/* Wait till HSI is used as system clock source */
while (RCC_GetSYSCLKSource() != 0x04)
{}
}
else
{
/* If HSI fails to start-up, the application will have wrong clock configuration.
User can add here some code to deal with this error */
/* Go to infinite loop */
while (1)
{}
}
/* Configure all GPIO as analog to reduce current consumption on non used IOs */
/* Enable GPIOs clock */
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA | RCC_AHBPeriph_GPIOB | RCC_AHBPeriph_GPIOC |
RCC_AHBPeriph_GPIOD | RCC_AHBPeriph_GPIOE | RCC_AHBPeriph_GPIOH |
RCC_AHBPeriph_GPIOF | RCC_AHBPeriph_GPIOG, ENABLE);
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_40MHz;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_All;
GPIO_Init(GPIOC, &GPIO_InitStructure);
GPIO_Init(GPIOD, &GPIO_InitStructure);
GPIO_Init(GPIOE, &GPIO_InitStructure);
GPIO_Init(GPIOH, &GPIO_InitStructure);
GPIO_Init(GPIOF, &GPIO_InitStructure);
GPIO_Init(GPIOG, &GPIO_InitStructure);
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_Init(GPIOB, &GPIO_InitStructure);
/* Disable GPIOs clock */
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA | RCC_AHBPeriph_GPIOB | RCC_AHBPeriph_GPIOC |
RCC_AHBPeriph_GPIOD | RCC_AHBPeriph_GPIOE | RCC_AHBPeriph_GPIOH |
RCC_AHBPeriph_GPIOF | RCC_AHBPeriph_GPIOG, DISABLE);
/* Configure Key Button*/
STM_EVAL_PBInit(BUTTON_KEY,BUTTON_MODE_GPIO);
/* Wait Until Key button pressed */
while(STM_EVAL_PBGetState(BUTTON_KEY) == RESET)
{
}
/* Wait Until Key button pressed */
while(STM_EVAL_PBGetState(BUTTON_KEY) != RESET)
{
}
/* Configure Key Button*/
STM_EVAL_PBInit(BUTTON_KEY,BUTTON_MODE_EXTI);
/* Request to enter SLEEP mode with regulator ON */
PWR_EnterSleepMode(PWR_Regulator_ON, PWR_SLEEPEntry_WFI);
/* Initialize LED1 on STM32L152-EVAL board */
STM_EVAL_LEDInit(LED1);
/* Infinite loop */
while (1)
{
/* Toggle The LED1 */
STM_EVAL_LEDToggle(LED1);
/* Inserted Delay */
for(index = 0; index < 0x5FFFF; index++);
}
}
//**************************************************************************//
void hal_system_RCC_init(void)
{
RCC_DeInit();//RCC system reset(for debug purpose)
RCC_HSEConfig(RCC_HSE_ON);//Enable HSE
//RCC_HSEConfig(RCC_HSE_ON);
if ( RCC_WaitForHSEStartUp() == SUCCESS)
{
FLASH_ReadAccess64Cmd(ENABLE);
FLASH_PrefetchBufferCmd(ENABLE);
// Flash 0 wait state
FLASH_SetLatency(FLASH_Latency_1);
//Power enable
RCC->APB1ENR |= RCC_APB1ENR_PWREN;
// Select the Voltage Range 1 (1.8 V) */
PWR->CR = PWR_CR_VOS_0;
// HCLK = SYSCLK
RCC_HCLKConfig(RCC_SYSCLK_Div1);
// PCLK2 = HCLK
RCC_PCLK2Config(RCC_HCLK_Div1);
// PCLK1 = HCLK
RCC_PCLK1Config(RCC_HCLK_Div1);
//PLLCLK = 16MHz *4/2 = 32 MHz
RCC_PLLConfig(RCC_PLLSource_HSE, RCC_PLLMul_4,RCC_PLLDiv_2);//RCC_PLLDiv_2
//RCC_PLLConfig(RCC_PLLSource_HSI, RCC_PLLMul_4,RCC_PLLDiv_2);
RCC_PLLCmd(ENABLE);// Enable PLL
while (RCC_GetFlagStatus(RCC_FLAG_PLLRDY) == RESET)// Wait till PLL is ready
{}
RCC_SYSCLKConfig(RCC_SYSCLKSource_PLLCLK);//Select PLL as system clock source
//RCC_HCLKConfig(RCC_SYSCLK_Div1);// HCLK = SYSCLK
//RCC_PCLK2Config(RCC_HCLK_Div1);// PCLK2 = HCLK/4
//RCC_PCLK1Config(RCC_HCLK_Div1);//RCC_HCLK_Div1 PCLK1 = HCLK/1
/* Wait till PLL is used as system clock source */
// while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)RCC_CFGR_SWS_HSE)
// {
// }
}
//SystemInit();
/*RCC_ClocksTypeDef RCC_ClockFreq;
RCC_ClockFreq.SYSCLK_Frequency=RCC_SYSCLKSource_HSE;
RCC_ClockFreq.HCLK_Frequency=RCC_SYSCLK_Div1;
RCC_ClockFreq.PCLK1_Frequency=RCC_HCLK_Div1;
RCC_ClockFreq.PCLK2_Frequency=RCC_HCLK_Div2;
RCC_GetClocksFreq(&RCC_ClockFreq);*/
RCC_ClockSecuritySystemCmd(ENABLE);
}
