/*************************************************************************//**
* @brief
* This function locks the debug interface by first enabling debug mode by
* bit-banging a SWD init sequence on the SWD interface and then setting
* the Debug lock bit in the flash.
* @return
* Returns true if the DLW has been sucessfully set, false otherwise.
****************************************************************************/
__ramfunc bool DEBUGLOCK_lock(void)
{
/* Start debug interface. */
DEBUGLOCK_startDebugInterface();
/* Set the debug lock word */
FLASH_writeWord(DEBUG_LOCK_WORD, 0x0);
/* Verify sucessful write by checking the DLW. */
if (*((uint32_t *) DEBUG_LOCK_WORD) == 0x0)
{
return true;
}
return false;
}
/**************************************************************************//**
* @brief
* The main command line loop. Placed in Ram so that it can still run after
* a destructive write operation.
* NOTE: __ramfunc is a IAR specific instruction to put code into RAM.
* This allows the bootloader to survive a destructive upload.
*****************************************************************************/
static void commandlineLoop( void )
{
uint8_t c;
/* The main command loop */
while (1)
{
/* Retrieve new character */
c = BOOTLDIO_rxByte();
/* Echo */
if (c != 0)
{
BOOTLDIO_txByte( c );
}
switch (c)
{
/* Bootloader version command */
case 'i':
/* Print version */
BOOTLDIO_printString("\r\n\r\n" BOOTLOADER_VERSION_STRING );
/* Print the chip ID */
BOOTLDIO_printHex(DEVINFO->UNIQUEH);
BOOTLDIO_printHex(DEVINFO->UNIQUEL);
BOOTLDIO_printString("\r\n");
break;
/* Upload command */
case 'u':
BOOTLDIO_printString( readyString );
XMODEM_download( BOOTLOADER_SIZE, flashSize );
break;
/* Destructive upload command */
case 'd':
BOOTLDIO_printString( readyString );
XMODEM_download( 0, flashSize );
break;
/* Write to user page */
case 't':
BOOTLDIO_printString( readyString );
XMODEM_download( USER_PAGE_START, USER_PAGE_END );
break;
/* Write to lock bits */
case 'p':
BOOTLDIO_printString( readyString );
XMODEM_download( LOCK_PAGE_START, LOCK_PAGE_END );
break;
/* Boot into new program */
case 'b':
Disconnect( 5000, 2000 );
BOOT_boot();
break;
/* Debug lock */
case 'l':
#if defined( BL_DEBUG )
/* We check if there is a debug session active in DHCSR. If there is we
* abort the locking. This is because we wish to make sure that the debug
* lock functionality works without a debugger attatched. */
if ((CoreDebug->DHCSR & CoreDebug_DHCSR_C_DEBUGEN_Msk) != 0x0)
{
USB_PUTS( "\r\n\r\n **** WARNING: DEBUG SESSION ACTIVE. NOT LOCKING! **** \r\n\r\n" );
BOOTLDIO_printString( "Debug active.\r\n" );
}
else
{
USB_PUTS( "Starting debug lock sequence.\r\n" );
#endif
FLASH_writeWord( DEBUG_LOCK_WORD, 0x0 );
if ( *(volatile uint32_t*)DEBUG_LOCK_WORD == 0x0 )
{
BOOTLDIO_printString( okString );
}
else
{
BOOTLDIO_printString( failString );
}
#if defined( BL_DEBUG )
USB_PRINTF( "Debug lock word: 0x%x \r\n", *((uint32_t *) DEBUG_LOCK_WORD) );
}
#endif
break;
/* Verify content by calculating CRC of entire flash */
case 'v':
verify( 0, flashSize );
break;
/* Verify content by calculating CRC of application area */
case 'c':
verify( BOOTLOADER_SIZE, flashSize );
break;
/* Verify content by calculating CRC of user page.*/
case 'n':
verify( USER_PAGE_START, USER_PAGE_END );
break;
/* Verify content by calculating CRC of lock page */
case 'm':
verify( LOCK_PAGE_START, LOCK_PAGE_END );
break;
/* Reset command */
case 'r':
Disconnect( 5000, 2000 );
/* Write to the Application Interrupt/Reset Command Register to reset
* the EFM32. See section 9.3.7 in the reference manual. */
SCB->AIRCR = 0x05FA0004;
break;
/* Unknown command */
case 0:
/* Timeout waiting for RX - avoid printing the unknown string. */
break;
default:
BOOTLDIO_printString( unknownString );
}
}
}
