//*************************************************************************************************************************
//NAME: initSysCtrl
//
//DESC: Initialize the system
//
//DATE: 23 March 2016
//
//AUTHOR: Dylan Schindler
//*************************************************************************************************************************
void InitSysCtrl(void)
{
// Disable Watchdog
WatchDogDisable();
#ifdef _FLASH
// If true then #define _FLASH has been provided to linker meaning code will be
// to flash memory.
// Copy time critical code and Flash setup code to RAM. This includes function InitFlash()
// The RamfuncsRunstart, RamfuncsLoadStart, and RamfuncsLoadSize are created by the linker.
// These can be found in the device .cmd file.
memcpy(&RamfuncsRunStart, &RamfuncsLoadStart, (size_t)&RamfuncsLoadSize);
// Call Flash Initilization to setup flash waitstates. --> This function must reside in RAM.
InitFlashAPS(0);
InitFlashAPS(1);
#endif
//enable pull-ups on unbonded IOs as soon as possible to reduce power consumption.
GPIO_EnableUnbondedIOPullups();
EALLOW;
CpuSysRegs.PCLKCR13.bit.ADC_A = 1;
CpuSysRegs.PCLKCR13.bit.ADC_B = 1;
CpuSysRegs.PCLKCR13.bit.ADC_C = 1;
CpuSysRegs.PCLKCR13.bit.ADC_D = 1;
//check if device is trimmed
if(*((Uint16 *)0x5D1B6) == 0x0000){
//device is not trimmed, apply static calibration values
AnalogSubsysRegs.ANAREFTRIMA.all = 31709;
AnalogSubsysRegs.ANAREFTRIMB.all = 31709;
AnalogSubsysRegs.ANAREFTRIMC.all = 31709;
AnalogSubsysRegs.ANAREFTRIMD.all = 31709;
}
CpuSysRegs.PCLKCR13.bit.ADC_A = 0;
CpuSysRegs.PCLKCR13.bit.ADC_B = 0;
CpuSysRegs.PCLKCR13.bit.ADC_C = 0;
CpuSysRegs.PCLKCR13.bit.ADC_D = 0;
EDIS;
#ifndef _TEST
//USB is being used.
initSysPLL(0);
#endif
//USB is not being used.
initSysPLL(0);
//Initialize peripheral clocks
initPeripheralClocks();
}
void InitSysCtrl(void)
{
// Disable the watchdog
DisableDog();
#ifdef _FLASH
// Copy time critical code and Flash setup code to RAM
// This includes the following functions: InitFlash();
// The RamfuncsLoadStart, RamfuncsLoadSize, and RamfuncsRunStart
// symbols are created by the linker. Refer to the device .cmd file.
memcpy(&RamfuncsRunStart, &RamfuncsLoadStart, (size_t)&RamfuncsLoadSize);
// Call Flash Initialization to setup flash waitstates
// This function must reside in RAM
InitFlash();
#endif
// *IMPORTANT*
// The Device_cal function, which copies the ADC & oscillator calibration values
// from TI reserved OTP into the appropriate trim registers, occurs automatically
// in the Boot ROM. If the boot ROM code is bypassed during the debug process, the
// following function MUST be called for the ADC and oscillators to function according
// to specification. The clocks to the ADC MUST be enabled before calling this
// function.
// See the device data manual and/or the ADC Reference
// Manual for more information.
#ifdef CPU1
EALLOW;
//enable pull-ups on unbonded IOs as soon as possible to reduce power consumption.
GPIO_EnableUnbondedIOPullups();
CpuSysRegs.PCLKCR13.bit.ADC_A = 1;
CpuSysRegs.PCLKCR13.bit.ADC_B = 1;
CpuSysRegs.PCLKCR13.bit.ADC_C = 1;
CpuSysRegs.PCLKCR13.bit.ADC_D = 1;
//check if device is trimmed
if(*((Uint16 *)0x5D1B6) == 0x0000){
//device is not trimmed, apply static calibration values
AnalogSubsysRegs.ANAREFTRIMA.all = 31709;
AnalogSubsysRegs.ANAREFTRIMB.all = 31709;
AnalogSubsysRegs.ANAREFTRIMC.all = 31709;
AnalogSubsysRegs.ANAREFTRIMD.all = 31709;
}
CpuSysRegs.PCLKCR13.bit.ADC_A = 0;
CpuSysRegs.PCLKCR13.bit.ADC_B = 0;
CpuSysRegs.PCLKCR13.bit.ADC_C = 0;
CpuSysRegs.PCLKCR13.bit.ADC_D = 0;
EDIS;
// Initialize the PLL control: PLLCR and CLKINDIV
// F28_PLLCR and F28_CLKINDIV are defined in F2837xD_Examples.h
// Note: The internal oscillator CANNOT be used as the PLL source if the
// PLLSYSCLK is configured to frequencies above 194 MHz.
InitSysPll(XTAL_OSC,IMULT_20,FMULT_1,PLLCLK_BY_2); //PLLSYSCLK = 20MHz(XTAL_OSC) * 20 (IMULT) * 1 (FMULT) / 2 (PLLCLK_BY_2)
//Turn on all peripherals
InitPeripheralClocks();
#endif
}
