/* ---------------------------------------------------------------------------
* creates a new pin in an element
*/
PinTypePtr
CreateNewPin (ElementTypePtr Element,
LocationType X, LocationType Y,
BDimension Thickness, BDimension Clearance, BDimension Mask,
BDimension DrillingHole, char *Name, char *Number,
FlagType Flags)
{
PinTypePtr pin = GetPinMemory (Element);
/* copy values */
pin->X = X;
pin->Y = Y;
pin->Thickness = Thickness;
pin->Clearance = Clearance;
pin->Mask = Mask;
pin->Name = STRDUP (Name);
pin->Number = STRDUP (Number);
pin->Flags = Flags;
CLEAR_FLAG (WARNFLAG, pin);
SET_FLAG (PINFLAG, pin);
pin->ID = ID++;
pin->Element = Element;
/*
* If there is no vendor drill map installed, this will simply
* return DrillingHole.
*/
pin->DrillingHole = vendorDrillMap (DrillingHole);
/* Unless we should not map drills on this element, map them! */
if (vendorIsElementMappable (Element))
{
if (pin->DrillingHole < MIN_PINORVIASIZE)
{
Message (_
("Did not map pin #%s (%s) drill hole because %6.2f mil is below the minimum allowed size\n"),
UNKNOWN (Number), UNKNOWN (Name),
0.01 * pin->DrillingHole);
pin->DrillingHole = DrillingHole;
}
else if (pin->DrillingHole > MAX_PINORVIASIZE)
{
Message (_
("Did not map pin #%s (%s) drill hole because %6.2f mil is above the maximum allowed size\n"),
UNKNOWN (Number), UNKNOWN (Name),
0.01 * pin->DrillingHole);
pin->DrillingHole = DrillingHole;
}
else if (!TEST_FLAG (HOLEFLAG, pin)
&& (pin->DrillingHole > pin->Thickness - MIN_PINORVIACOPPER))
{
Message (_
("Did not map pin #%s (%s) drill hole because %6.2f mil does not leave enough copper\n"),
UNKNOWN (Number), UNKNOWN (Name),
0.01 * pin->DrillingHole);
pin->DrillingHole = DrillingHole;
}
}
else
{
pin->DrillingHole = DrillingHole;
}
if (pin->DrillingHole != DrillingHole)
{
Message (_
("Mapped pin drill hole to %.2f mils from %.2f mils per vendor table\n"),
0.01 * pin->DrillingHole, 0.01 * DrillingHole);
}
return (pin);
}
/*!
* \brief Creates a new pin in an element.
*/
PinType *
CreateNewPin (ElementType *Element,
Coord X, Coord Y,
Coord Thickness, Coord Clearance, Coord Mask,
Coord DrillingHole, char *Name, char *Number,
FlagType Flags)
{
PinType *pin = GetPinMemory (Element);
/* copy values */
pin->X = X;
pin->Y = Y;
pin->Thickness = Thickness;
pin->Clearance = Clearance;
pin->Mask = Mask;
pin->Name = STRDUP (Name);
pin->Number = STRDUP (Number);
pin->Flags = Flags;
CLEAR_FLAG (WARNFLAG, pin);
SET_FLAG (PINFLAG, pin);
pin->ID = ID++;
pin->Element = Element;
/*
* If there is no vendor drill map installed, this will simply
* return DrillingHole.
*/
pin->DrillingHole = vendorDrillMap (DrillingHole);
/* Unless we should not map drills on this element, map them! */
if (vendorIsElementMappable (Element))
{
if (pin->DrillingHole < MIN_PINORVIASIZE)
{
Message (_("%m+Did not map pin #%s (%s) drill hole because %$mS is below the minimum allowed size\n"),
Settings.grid_unit->allow, UNKNOWN (Number), UNKNOWN (Name), pin->DrillingHole);
pin->DrillingHole = DrillingHole;
}
else if (pin->DrillingHole > MAX_PINORVIASIZE)
{
Message (_("%m+Did not map pin #%s (%s) drill hole because %$mS is above the maximum allowed size\n"),
Settings.grid_unit->allow, UNKNOWN (Number), UNKNOWN (Name), pin->DrillingHole);
pin->DrillingHole = DrillingHole;
}
else if (!TEST_FLAG (HOLEFLAG, pin)
&& (pin->DrillingHole > pin->Thickness - MIN_PINORVIACOPPER))
{
Message (_("%m+Did not map pin #%s (%s) drill hole because %$mS does not leave enough copper\n"),
Settings.grid_unit->allow, UNKNOWN (Number), UNKNOWN (Name), pin->DrillingHole);
pin->DrillingHole = DrillingHole;
}
}
else
{
pin->DrillingHole = DrillingHole;
}
if (pin->DrillingHole != DrillingHole)
{
Message (_("%m+Mapped pin drill hole to %$mS from %$mS per vendor table\n"),
Settings.grid_unit->allow, pin->DrillingHole, DrillingHole);
}
return (pin);
}
