int serial_getc(serial_t *obj)
{
PHAL_RUART_ADAPTER pHalRuartAdapter=(PHAL_RUART_ADAPTER)&(obj->hal_uart_adp);
u8 uart_idx = pHalRuartAdapter->UartIndex;
while (!serial_readable(obj));
return (int)((HAL_RUART_READ32(uart_idx, RUART_REV_BUF_REG_OFF)) & 0xFF);
}
void serial_break_clear(serial_t *obj)
{
PHAL_RUART_ADAPTER pHalRuartAdapter=(PHAL_RUART_ADAPTER)&(obj->hal_uart_adp);
u8 uart_idx = pHalRuartAdapter->UartIndex;
u32 RegValue;
RegValue = HAL_RUART_READ32(uart_idx, RUART_LINE_CTL_REG_OFF);
RegValue &= ~(BIT_UART_LCR_BREAK_CTRL);
HAL_RUART_WRITE32(uart_idx, RUART_LINE_CTL_REG_OFF, RegValue);
}
int serial_readable(serial_t *obj)
{
PHAL_RUART_ADAPTER pHalRuartAdapter=(PHAL_RUART_ADAPTER)&(obj->hal_uart_adp);
u8 uart_idx = pHalRuartAdapter->UartIndex;
if ((HAL_RUART_READ32(uart_idx, RUART_LINE_STATUS_REG_OFF)) & RUART_LINE_STATUS_REG_DR) {
return 1;
}
else {
return 0;
}
}
int serial_getc(serial_t *obj)
{
#ifdef CONFIG_MBED_ENABLED
if (obj->index == UART_3) {
return log_uart_getc(&stdio_uart_log);
}
#endif
PHAL_RUART_ADAPTER pHalRuartAdapter=(PHAL_RUART_ADAPTER)&(obj->hal_uart_adp);
u8 uart_idx = pHalRuartAdapter->UartIndex;
while (!serial_readable(obj));
return (int)((HAL_RUART_READ32(uart_idx, RUART_REV_BUF_REG_OFF)) & 0xFF);
}
void serial_break_clear(serial_t *obj)
{
#ifdef CONFIG_MBED_ENABLED
if (obj->index == UART_3) {
log_uart_break_clear(&stdio_uart_log);
return;
}
#endif
PHAL_RUART_ADAPTER pHalRuartAdapter=(PHAL_RUART_ADAPTER)&(obj->hal_uart_adp);
u8 uart_idx = pHalRuartAdapter->UartIndex;
u32 RegValue;
RegValue = HAL_RUART_READ32(uart_idx, RUART_LINE_CTL_REG_OFF);
RegValue &= ~(BIT_UART_LCR_BREAK_CTRL);
HAL_RUART_WRITE32(uart_idx, RUART_LINE_CTL_REG_OFF, RegValue);
}
int serial_writable(serial_t *obj)
{
#ifdef CONFIG_MBED_ENABLED
if (obj->index == UART_3) {
return log_uart_writable(&stdio_uart_log);
}
#endif
PHAL_RUART_ADAPTER pHalRuartAdapter=(PHAL_RUART_ADAPTER)&(obj->hal_uart_adp);
u8 uart_idx = pHalRuartAdapter->UartIndex;
if (HAL_RUART_READ32(uart_idx, RUART_LINE_STATUS_REG_OFF) & (RUART_LINE_STATUS_REG_THRE)) {
return 1;
} else {
return 0;
}
}
HAL_Status
HalRuartInitRtl8195a_Patch(
IN VOID *Data ///< RUART Adapter
)
{
/* DBG_ENTRANCE; */
u32 RegValue;
u32 Divisor;
u32 Dll;
u32 Dlm;
u8 UartIndex;
s32 ElementIndex;
RUART_SPEED_SETTING RuartSpeedSetting;
u8 PinmuxSelect;
PHAL_RUART_ADAPTER pHalRuartAdapter = (PHAL_RUART_ADAPTER) Data;
UartIndex = pHalRuartAdapter->UartIndex;
PinmuxSelect = pHalRuartAdapter->PinmuxSelect;
if (UartIndex > 2) {
DBG_UART_ERR(ANSI_COLOR_MAGENTA"HalRuartInitRtl8195a: Invalid UART Index\n"ANSI_COLOR_RESET);
return HAL_ERR_PARA;
}
DBG_UART_INFO("%s==>\n", __FUNCTION__);
DBG_UART_INFO("HalRuartInitRtl8195a: [UART %d] PinSel=%d\n", UartIndex, PinmuxSelect);
if(( PinmuxSelect == RUART0_MUX_TO_GPIOE ) && ((UartIndex == 0) || (UartIndex == 1))) {
// confict with J-Teg pin, so we disable the J-Teg
DBG_UART_WARN(ANSI_COLOR_MAGENTA"Disable JTAG function due to pin conflict\n"ANSI_COLOR_RESET);
JTAG_PIN_FCTRL(OFF);
}
// switch Pin from EEPROM to UART0
if(( PinmuxSelect == RUART0_MUX_TO_GPIOC ) && (UartIndex == 0)) {
RegValue = HAL_READ32(SYSTEM_CTRL_BASE, 0xa4);
if (RegValue & 0x10) {
DBG_UART_WARN("Disable EEPROM Pin for UART 0\n");
HAL_WRITE32(SYSTEM_CTRL_BASE, 0xa4, (RegValue & (~0x10)));
}
}
switch (UartIndex) {
case 0:
/* UART 0 */
ACTCK_UART0_CCTRL(ON);
SLPCK_UART0_CCTRL(ON);
PinCtrl(UART0, PinmuxSelect, ON);
UART0_FCTRL(ON);
UART0_BD_FCTRL(ON);
break;
case 1:
/* UART 1 */
ACTCK_UART1_CCTRL(ON);
SLPCK_UART1_CCTRL(ON);
PinCtrl(UART1, PinmuxSelect, ON);
UART1_FCTRL(ON);
UART1_BD_FCTRL(ON);
break;
case 2:
/* UART 1 */
ACTCK_UART2_CCTRL(ON);
SLPCK_UART2_CCTRL(ON);
PinCtrl(UART2, PinmuxSelect, ON);
UART2_FCTRL(ON);
UART2_BD_FCTRL(ON);
break;
default:
DBG_UART_ERR("Invalid UART Index(%d)\n", UartIndex);
return HAL_ERR_PARA;
}
/* Reset RX FIFO */
HalRuartResetRxFifoRtl8195a(Data);
DBG_UART_INFO(ANSI_COLOR_CYAN"HAL UART Init[UART %d]\n"ANSI_COLOR_RESET, UartIndex);
/* Disable all interrupts */
HAL_RUART_WRITE32(UartIndex, RUART_INTERRUPT_EN_REG_OFF, 0x00);
/* Set DLAB bit to 1 to access DLL/DLM */
RegValue = HAL_RUART_READ32(UartIndex, RUART_LINE_CTL_REG_OFF);
RegValue |= RUART_LINE_CTL_REG_DLAB_ENABLE;
HAL_RUART_WRITE32(UartIndex, RUART_LINE_CTL_REG_OFF, RegValue);
DBG_UART_INFO("[R] RUART_LINE_CTL_REG_OFF(0x0C) = %x\n", HAL_RUART_READ32(UartIndex, RUART_LINE_CTL_REG_OFF));
/* Set Baudrate Division */
#if 1
ElementIndex = FindElementIndex(pHalRuartAdapter->BaudRate, BAUDRATE);
if (ElementIndex < 0) {
ElementIndex = 5;
DBG_UART_ERR("Invalid BaudRate(%d), Force it as default(%d)\n", pHalRuartAdapter->BaudRate, BAUDRATE[ElementIndex]);
}
RuartSpeedSetting.BaudRate = BAUDRATE[ElementIndex];
RuartSpeedSetting.Ovsr = OVSR_PATCH[ElementIndex];
RuartSpeedSetting.Div = DIV_PATCH[ElementIndex];
RuartSpeedSetting.Ovsr_adj = OVSR_ADJ_PATCH[ElementIndex];
#else
RuartSpeedSetting.BaudRate = 38400;
RuartSpeedSetting.Ovsr = 10;
RuartSpeedSetting.Div = 217;
RuartSpeedSetting.Ovsr_adj = 0x0;
#endif
DBG_UART_INFO("Baud %d, Ovsr %d, Div %d, OvsrAdj 0x%X\n",
RuartSpeedSetting.BaudRate,
RuartSpeedSetting.Ovsr,
RuartSpeedSetting.Div,
RuartSpeedSetting.Ovsr_adj
);
/* Divisor = (SYSTEM_CLK / ((ovsr + 5 + ovsr_adj/11) * (UartAdapter.BaudRate))); */
/* Set Divisor */
Divisor = RuartSpeedSetting.Div;
Dll = Divisor & 0xFF;
Dlm = (Divisor & 0xFF00) >> 8;
DBG_UART_INFO("Calculated Dll, Dlm = %02x, %02x\n", Dll, Dlm);
DBG_UART_INFO("---- Before setting baud rate ----\n");
DBG_UART_INFO(" [R] RUART_DLL_OFF(0x00) = %x\n", HAL_RUART_READ32(UartIndex, RUART_DLL_OFF));
DBG_UART_INFO(" [R] RUART_DLM_OFF(0x04) = %x\n", HAL_RUART_READ32(UartIndex, RUART_DLM_OFF));
HAL_RUART_WRITE32(UartIndex, RUART_DLL_OFF, Dll);
HAL_RUART_WRITE32(UartIndex, RUART_DLM_OFF, Dlm);
DBG_UART_INFO("---- After setting baud rate ----\n");
DBG_UART_INFO(" [R] RUART_DLL_OFF(0x00) = %x\n", HAL_RUART_READ32(UartIndex, RUART_DLL_OFF));
DBG_UART_INFO(" [R] RUART_DLM_OFF(0x04) = %x\n", HAL_RUART_READ32(UartIndex, RUART_DLM_OFF));
DBG_UART_INFO(ANSI_COLOR_CYAN"---- Befor OVSR & OVSR_ADJ ----\n"ANSI_COLOR_RESET);
RegValue = HAL_RUART_READ32(UartIndex, RUART_SCRATCH_PAD_REG_OFF);
DBG_UART_INFO("UART%d SPR(0x1C) = %X\n", UartIndex, RegValue);
RegValue = HAL_RUART_READ32(UartIndex, RUART_STS_REG_OFF);
DBG_UART_INFO("UART%d SIS(0x20) = %X\n", UartIndex, RegValue);
/**
* Clean Rx break signal interrupt status at initial stage.
*/
RegValue = HAL_RUART_READ32(UartIndex, RUART_SCRATCH_PAD_REG_OFF);
RegValue |= RUART_SP_REG_RXBREAK_INT_STATUS;
HAL_RUART_WRITE32(UartIndex, RUART_SCRATCH_PAD_REG_OFF, RegValue);
/* Set OVSR(xfactor) */
RegValue = HAL_RUART_READ32(UartIndex, RUART_STS_REG_OFF);
RegValue &= ~(RUART_STS_REG_XFACTOR);
RegValue |= (((RuartSpeedSetting.Ovsr - 5) << 4) & RUART_STS_REG_XFACTOR);
HAL_RUART_WRITE32(UartIndex, RUART_STS_REG_OFF, RegValue);
/* Set OVSR_ADJ[10:0] (xfactor_adj[26:16]) */
RegValue = HAL_RUART_READ32(UartIndex, RUART_SCRATCH_PAD_REG_OFF);
RegValue &= ~(RUART_SP_REG_XFACTOR_ADJ);
RegValue |= ((RuartSpeedSetting.Ovsr_adj << 16) & RUART_SP_REG_XFACTOR_ADJ);
HAL_RUART_WRITE32(UartIndex, RUART_SCRATCH_PAD_REG_OFF, RegValue);
DBG_UART_INFO(ANSI_COLOR_CYAN"---- After OVSR & OVSR_ADJ ----\n"ANSI_COLOR_RESET);
RegValue = HAL_RUART_READ32(UartIndex, RUART_SCRATCH_PAD_REG_OFF);
DBG_UART_INFO("UART%d SPR(0x1C) = %X\n", UartIndex, RegValue);
RegValue = HAL_RUART_READ32(UartIndex, RUART_STS_REG_OFF);
DBG_UART_INFO("UART%d SIS(0x20) = %X\n", UartIndex, RegValue);
/* clear DLAB bit */
RegValue = HAL_RUART_READ32(UartIndex, RUART_LINE_CTL_REG_OFF);
RegValue &= ~(RUART_LINE_CTL_REG_DLAB_ENABLE);
HAL_RUART_WRITE32(UartIndex, RUART_LINE_CTL_REG_OFF, RegValue);
DBG_UART_INFO("[R] RUART_LINE_CTL_REG_OFF(0x0C) = %x\n", HAL_RUART_READ32(UartIndex, RUART_LINE_CTL_REG_OFF));
DBG_UART_INFO("[R] UART%d INT_EN(0x04) = %x\n", UartIndex, pHalRuartAdapter->Interrupts);
RegValue = ((pHalRuartAdapter->Interrupts) & 0xFF);
HAL_RUART_WRITE32(UartIndex, RUART_INTERRUPT_EN_REG_OFF, RegValue);
DBG_UART_INFO("[W] UART%d INT_EN(0x04) = %x\n", UartIndex, RegValue);
/* Configure FlowControl */
if (pHalRuartAdapter->FlowControl == AUTOFLOW_ENABLE) {
RegValue = HAL_RUART_READ32(UartIndex, RUART_MODEM_CTL_REG_OFF);
RegValue |= RUART_MCL_AUTOFLOW_ENABLE;
HAL_RUART_WRITE32(UartIndex, RUART_MODEM_CTL_REG_OFF, RegValue);
}
/* RUART DMA Initialization */
HalRuartDmaInitRtl8195a(pHalRuartAdapter);
DBG_UART_INFO("[R] UART%d LCR(0x%02X): %X\n", UartIndex, RUART_LINE_CTL_REG_OFF, HAL_RUART_READ32(UartIndex, RUART_LINE_CTL_REG_OFF));
RegValue = HAL_RUART_READ32(UartIndex, RUART_LINE_CTL_REG_OFF);
/* PARITY CONTROL */
RegValue &= BIT_CLR_LCR_WLS;
RegValue |= BIT_LCR_WLS(pHalRuartAdapter->WordLen);
RegValue &= BIT_INVC_LCR_STB_EN;
RegValue |= BIT_LCR_STB_EN(pHalRuartAdapter->StopBit);
RegValue &= BIT_INVC_LCR_PARITY_EN;
RegValue |= BIT_LCR_PARITY_EN(pHalRuartAdapter->Parity);
/* PARITY TYPE SELECT */
RegValue &= BIT_INVC_LCR_PARITY_TYPE;
RegValue |= BIT_LCR_PARITY_TYPE(pHalRuartAdapter->ParityType);
/* STICK PARITY CONTROL */
RegValue &= BIT_INVC_LCR_STICK_PARITY_EN;
RegValue |= BIT_LCR_STICK_PARITY_EN(pHalRuartAdapter->StickParity);
HAL_RUART_WRITE32(UartIndex, RUART_LINE_CTL_REG_OFF, RegValue);
DBG_UART_INFO("[W] UART%d LCR(0x%02X): %X\n", UartIndex, RUART_LINE_CTL_REG_OFF, HAL_RUART_READ32(UartIndex, RUART_LINE_CTL_REG_OFF));
/* Need to assert RTS during initial stage. */
if (pHalRuartAdapter->FlowControl == AUTOFLOW_ENABLE) {
HalRuartRTSCtrlRtl8195a(Data, 1);
}
pHalRuartAdapter->State = HAL_UART_STATE_READY;
return HAL_OK;
}