void MX_UART4_DeInit(void){
point=0;
ready =0;
HAL_UART_MspDeInit(&huart4);
}
void uartTester(){
//UART fogadás, teszteléshez ---------------------------------------------------------
uint8_t pData;
PutString("S");
HAL_UART_Receive(&huart1,&pData,1,100);
if(pData=='O'){
HAL_GPIO_TogglePin(Kimenet_GPIO_Port,Kimenet_Pin);
PutString("R");
HAL_UART_Receive(&huart1,&pData,1,1000);
while(pData != 'A')
HAL_UART_Receive(&huart1,&pData,1,1000);
HAL_GPIO_WritePin( DCDC_EN_GPIO_Port , DCDC_EN_Pin , 1 );
PutString("R");
HAL_UART_Receive(&huart1,&pData,8,1000);
while(pData != 'B')
HAL_UART_Receive(&huart1,&pData,8,1000);
soundNum=1;
sounDelay=10;
SystemClock_Config_48MHz();
HAL_Delay(2);
MX_TIM3_Init();
HAL_TIM_PWM_Init(&htim3);
sConfigOC.OCMode = TIM_OCMODE_PWM1;
sConfigOC.Pulse = 0;
sConfigOC.OCPolarity = TIM_OCPOLARITY_LOW;
sConfigOC.OCFastMode = TIM_OCFAST_DISABLE;
HAL_TIM_PWM_ConfigChannel( &htim3 , &sConfigOC , TIM_CHANNEL_1);
sConfigOC.OCPolarity = TIM_OCPOLARITY_HIGH;
HAL_TIM_PWM_ConfigChannel( &htim3 , &sConfigOC , TIM_CHANNEL_2);
HAL_GPIO_TogglePin(Kimenet_GPIO_Port,Kimenet_Pin);
HAL_TIM_PWM_Start(&htim3, TIM_CHANNEL_1);
HAL_TIM_PWM_Start(&htim3, TIM_CHANNEL_2);
uint16_t i=630;
__HAL_TIM_SetAutoreload(&htim3,i*2);
__HAL_TIM_SetCompare(&htim3,TIM_CHANNEL_1, i);
__HAL_TIM_SetCompare(&htim3,TIM_CHANNEL_2, i);
HAL_Delay(500);
PutString("R");
HAL_UART_Receive(&huart1,&pData,8,1000);
while(pData != 'C')
HAL_UART_Receive(&huart1,&pData,8,1000);
HAL_GPIO_WritePin( DCDC_EN_GPIO_Port , DCDC_EN_Pin , 0);
HAL_TIM_PWM_Stop( &htim3 , TIM_CHANNEL_1 );
HAL_TIM_PWM_Stop( &htim3 , TIM_CHANNEL_2 );
HAL_TIM_PWM_DeInit( &htim3 );
SystemClock_Config_8MHz();
HAL_ADC_MspDeInit(&hadc);
HAL_UART_MspDeInit(&huart1);
HAL_TIM_Base_DeInit(&htim3);
while(1){
HAL_GPIO_TogglePin(Kimenet_GPIO_Port,Kimenet_Pin);
HAL_Delay(200);
}
}
}
/******************************************************************************
* @brief Deinitialise modem UART interface.
* @param None
* @retval None
*****************************************************************************/
void Modem_IO_DeInit( void )
{
HAL_UART_MspDeInit(&huart2);
}
