/**
* @brief Initializes the COMP peripheral according to the specified parameters
* in COMP_InitStruct
* @note If the selected comparator is locked, initialization can't be performed.
* To unlock the configuration, perform a system reset.
* @note By default, PA1 is selected as COMP1 non inverting input.
* To use PA4 as COMP1 non inverting input call COMP_SwitchCmd() after COMP_Init()
* @param COMP_Selection: the selected comparator.
* This parameter can be one of the following values:
* @arg COMP_Selection_COMP1: COMP1 selected
* @arg COMP_Selection_COMP2: COMP2 selected
* @param COMP_InitStruct: pointer to an COMP_InitTypeDef structure that contains
* the configuration information for the specified COMP peripheral.
* @retval None
*/
void COMP_Init(uint32_t COMP_Selection, COMP_InitTypeDef* COMP_InitStruct)
{
uint32_t tmpreg = 0;
/* Check the parameters */
assert_param(IS_COMP_ALL_PERIPH(COMP_Selection));
assert_param(IS_COMP_INVERTING_INPUT(COMP_InitStruct->COMP_InvertingInput));
assert_param(IS_COMP_OUTPUT(COMP_InitStruct->COMP_Output));
assert_param(IS_COMP_OUTPUT_POL(COMP_InitStruct->COMP_OutputPol));
assert_param(IS_COMP_HYSTERESIS(COMP_InitStruct->COMP_Hysteresis));
assert_param(IS_COMP_MODE(COMP_InitStruct->COMP_Mode));
/*!< Get the COMP_CSR register value */
tmpreg = COMP->CSR;
/*!< Clear the COMP1SW1, COMPx_IN_SEL, COMPx_OUT_TIM_SEL, COMPx_POL, COMPx_HYST and COMPx_PWR_MODE bits */
tmpreg &= (uint32_t) ~(COMP_CSR_CLEAR_MASK<<COMP_Selection);
/*!< Configure COMP: inverting input, output redirection, hysteresis value and power mode */
/*!< Set COMPxINSEL bits according to COMP_InitStruct->COMP_InvertingInput value */
/*!< Set COMPxOUTSEL bits according to COMP_InitStruct->COMP_Output value */
/*!< Set COMPxPOL bit according to COMP_InitStruct->COMP_OutputPol value */
/*!< Set COMPxHYST bits according to COMP_InitStruct->COMP_Hysteresis value */
/*!< Set COMPxMODE bits according to COMP_InitStruct->COMP_Mode value */
tmpreg |= (uint32_t)((COMP_InitStruct->COMP_InvertingInput | COMP_InitStruct->COMP_Output |
COMP_InitStruct->COMP_OutputPol | COMP_InitStruct->COMP_Hysteresis |
COMP_InitStruct->COMP_Mode)<<COMP_Selection);
/*!< Write to COMP_CSR register */
COMP->CSR = tmpreg;
}
/**
* @brief Initializes the COMP peripheral according to the specified parameters
* in COMP_InitStruct
* @note If the selected comparator is locked, initialization can't be performed.
* To unlock the configuration, perform a system reset.
* @note By default, PA1 is selected as COMP1 non inverting input.
* To use PA4 as COMP1 non inverting input call COMP_SwitchCmd() after COMP_Init()
* @param COMP_Selection: the selected comparator.
* This parameter can be COMP_Selection_COMPx where x can be 1 to 7
* to select the COMP peripheral.
* @param COMP_InitStruct: pointer to an COMP_InitTypeDef structure that contains
* the configuration information for the specified COMP peripheral.
* - COMP_InvertingInput specifies the inverting input of COMP
* - COMP_NonInvertingInput specifies the non inverting input of COMP
* - COMP_Output connect COMP output to selected timer
* input (Input capture / Output Compare Reference Clear / Break Input)
* - COMP_BlankingSrce specifies the blanking source of COMP
* - COMP_OutputPol select output polarity
* - COMP_Hysteresis configures COMP hysteresis value
* - COMP_Mode configures COMP power mode
* @note COMP_Hysteresis must be configured only for STM32F303xC. Otherwise, COMP_Hysteresis
* must be kept at reset value(COMP_Hysteresis_No).
* @note COMP_Mode field is only applicable for STM32F303xC devices.
* @retval None
*/
void COMP_Init(uint32_t COMP_Selection, COMP_InitTypeDef* COMP_InitStruct)
{
uint32_t tmpreg = 0;
/* Check the parameters */
assert_param(IS_COMP_ALL_PERIPH(COMP_Selection));
assert_param(IS_COMP_INVERTING_INPUT(COMP_InitStruct->COMP_InvertingInput));
assert_param(IS_COMP_NONINVERTING_INPUT(COMP_InitStruct->COMP_NonInvertingInput));
assert_param(IS_COMP_OUTPUT(COMP_InitStruct->COMP_Output));
assert_param(IS_COMP_BLANKING_SOURCE(COMP_InitStruct->COMP_BlankingSrce));
assert_param(IS_COMP_OUTPUT_POL(COMP_InitStruct->COMP_OutputPol));
assert_param(IS_COMP_HYSTERESIS(COMP_InitStruct->COMP_Hysteresis));
assert_param(IS_COMP_MODE(COMP_InitStruct->COMP_Mode));
/*!< Get the COMPx_CSR register value */
tmpreg = *(__IO uint32_t *) (COMP_BASE + COMP_Selection);
/*!< Clear the COMP1SW1, COMPxINSEL, COMPxOUTSEL, COMPxPOL, COMPxHYST and COMPxMODE bits */
tmpreg &= (uint32_t) (COMP_CSR_CLEAR_MASK);
/*!< Configure COMP: inverting input, output redirection, hysteresis value and power mode */
/*!< Set COMPxINSEL bits according to COMP_InitStruct->COMP_InvertingInput value */
/*!< Set COMPxNONINSEL bits according to COMP_InitStruct->COMP_NonInvertingInput value */
/*!< Set COMPxBLANKING bits according to COMP_InitStruct->COMP_BlankingSrce value */
/*!< Set COMPxOUTSEL bits according to COMP_InitStruct->COMP_Output value */
/*!< Set COMPxPOL bit according to COMP_InitStruct->COMP_OutputPol value */
/*!< Set COMPxHYST bits according to COMP_InitStruct->COMP_Hysteresis value */
/*!< Set COMPxMODE bits according to COMP_InitStruct->COMP_Mode value */
tmpreg |= (uint32_t)(COMP_InitStruct->COMP_InvertingInput | COMP_InitStruct->COMP_NonInvertingInput |
COMP_InitStruct->COMP_Output | COMP_InitStruct->COMP_OutputPol | COMP_InitStruct->COMP_BlankingSrce |
COMP_InitStruct->COMP_Hysteresis | COMP_InitStruct->COMP_Mode);
/*!< Write to COMPx_CSR register */
*(__IO uint32_t *) (COMP_BASE + COMP_Selection) = tmpreg;
}
/**
* @brief Initialize the COMP peripheral according to the specified
* parameters in the COMP_InitTypeDef and initialize the associated handle.
* @note If the selected comparator is locked, initialization cannot be performed.
* To unlock the configuration, perform a system reset.
* @param hcomp COMP handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_COMP_Init(COMP_HandleTypeDef *hcomp)
{
HAL_StatusTypeDef status = HAL_OK;
/* Check the COMP handle allocation and lock status */
if((hcomp == NULL) || ((hcomp->State & COMP_STATE_BIT_LOCK) != RESET))
{
status = HAL_ERROR;
}
else
{
/* Check the parameters */
assert_param(IS_COMP_ALL_INSTANCE(hcomp->Instance));
assert_param(IS_COMP_INVERTINGINPUT(hcomp->Init.InvertingInput));
assert_param(IS_COMP_NONINVERTINGINPUT(hcomp->Init.NonInvertingInput));
assert_param(IS_COMP_NONINVERTINGINPUT_INSTANCE(hcomp->Instance, hcomp->Init.NonInvertingInput));
assert_param(IS_COMP_OUTPUT(hcomp->Init.Output));
assert_param(IS_COMP_OUTPUT_INSTANCE(hcomp->Instance, hcomp->Init.Output));
assert_param(IS_COMP_OUTPUTPOL(hcomp->Init.OutputPol));
assert_param(IS_COMP_HYSTERESIS(hcomp->Init.Hysteresis));
assert_param(IS_COMP_MODE(hcomp->Init.Mode));
assert_param(IS_COMP_BLANKINGSRCE(hcomp->Init.BlankingSrce));
assert_param(IS_COMP_BLANKINGSRCE_INSTANCE(hcomp->Instance, hcomp->Init.BlankingSrce));
assert_param(IS_COMP_TRIGGERMODE(hcomp->Init.TriggerMode));
if(hcomp->Init.WindowMode != COMP_WINDOWMODE_DISABLE)
{
assert_param(IS_COMP_WINDOWMODE_INSTANCE(hcomp->Instance));
assert_param(IS_COMP_WINDOWMODE(hcomp->Init.WindowMode));
}
/* Init SYSCFG and the low level hardware to access comparators */
__HAL_RCC_SYSCFG_CLK_ENABLE();
/* Init the low level hardware : SYSCFG to access comparators */
HAL_COMP_MspInit(hcomp);
if(hcomp->State == HAL_COMP_STATE_RESET)
{
/* Allocate lock resource and initialize it */
hcomp->Lock = HAL_UNLOCKED;
}
/* Set COMP parameters */
/* Set COMPxINSEL bits according to hcomp->Init.InvertingInput value */
/* Set COMPxNONINSEL bits according to hcomp->Init.NonInvertingInput value */
/* Set COMPxBLANKING bits according to hcomp->Init.BlankingSrce value */
/* Set COMPxOUTSEL bits according to hcomp->Init.Output value */
/* Set COMPxPOL bit according to hcomp->Init.OutputPol value */
/* Set COMPxHYST bits according to hcomp->Init.Hysteresis value */
/* Set COMPxMODE bits according to hcomp->Init.Mode value */
COMP_INIT(hcomp);
/* Initialize the COMP state*/
hcomp->State = HAL_COMP_STATE_READY;
}
return status;
}
/**
* @brief Initialize the COMP according to the specified
* parameters in the COMP_InitTypeDef and initialize the associated handle.
* @note If the selected comparator is locked, initialization can't be performed.
* To unlock the configuration, perform a system reset.
* @param hcomp COMP handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_COMP_Init(COMP_HandleTypeDef *hcomp)
{
uint32_t tmpcsr = 0;
HAL_StatusTypeDef status = HAL_OK;
/* Check the COMP handle allocation and lock status */
if((hcomp == NULL) || ((hcomp->State & COMP_STATE_BIT_LOCK) != RESET))
{
status = HAL_ERROR;
}
else
{
/* Check the parameters */
assert_param(IS_COMP_ALL_INSTANCE(hcomp->Instance));
assert_param(IS_COMP_INVERTINGINPUT(hcomp->Init.InvertingInput));
assert_param(IS_COMP_NONINVERTINGINPUT(hcomp->Init.NonInvertingInput));
assert_param(IS_COMP_OUTPUTPOL(hcomp->Init.OutputPol));
assert_param(IS_COMP_MODE(hcomp->Init.Mode));
assert_param(IS_COMP_HYSTERESIS(hcomp->Init.Hysteresis));
assert_param(IS_COMP_BLANKINGSRCE(hcomp->Init.BlankingSrce));
assert_param(IS_COMP_BLANKINGSRCE_INSTANCE(hcomp->Instance, hcomp->Init.BlankingSrce));
assert_param(IS_COMP_TRIGGERMODE(hcomp->Init.TriggerMode));
if(hcomp->Init.WindowMode != COMP_WINDOWMODE_DISABLE)
{
assert_param(IS_COMP_WINDOWMODE_INSTANCE(hcomp->Instance));
assert_param(IS_COMP_WINDOWMODE(hcomp->Init.WindowMode));
}
/* Init SYSCFG and the low level hardware to access comparators */
__HAL_RCC_SYSCFG_CLK_ENABLE();
/* Init the low level hardware : SYSCFG to access comparators */
HAL_COMP_MspInit(hcomp);
if(hcomp->State == HAL_COMP_STATE_RESET)
{
/* Allocate lock resource and initialize it */
hcomp->Lock = HAL_UNLOCKED;
}
/* Change COMP peripheral state */
hcomp->State = HAL_COMP_STATE_BUSY;
/* Set COMP parameters */
/* Set INMSEL bits according to hcomp->Init.InvertingInput value */
/* Set INPSEL bits according to hcomp->Init.NonInvertingInput value */
/* Set BLANKING bits according to hcomp->Init.BlankingSrce value */
/* Set HYST bits according to hcomp->Init.Hysteresis value */
/* Set POLARITY bit according to hcomp->Init.OutputPol value */
/* Set POWERMODE bits according to hcomp->Init.Mode value */
/* Set WINMODE bit according to hcomp->Init.WindowMode value */
tmpcsr = hcomp->Init.InvertingInput | \
hcomp->Init.NonInvertingInput | \
hcomp->Init.BlankingSrce | \
hcomp->Init.Hysteresis | \
hcomp->Init.OutputPol | \
hcomp->Init.Mode | \
hcomp->Init.WindowMode;
/* Check VREFINT use for NonInvertingInput */
if(hcomp->Init.InvertingInput == COMP_INVERTINGINPUT_VREFINT)
{
/* Enable voltage scaler to output VREFINT */
tmpcsr |= COMP_CSR_SCALEN;
}
else
{
if((hcomp->Init.InvertingInput == COMP_INVERTINGINPUT_1_4VREFINT) ||
(hcomp->Init.InvertingInput == COMP_INVERTINGINPUT_1_2VREFINT) ||
(hcomp->Init.InvertingInput == COMP_INVERTINGINPUT_3_4VREFINT))
{
/* Enable voltage & bandgap scaler to output VREFINT */
tmpcsr |= (COMP_CSR_BRGEN | COMP_CSR_SCALEN);
}
}
MODIFY_REG(hcomp->Instance->CSR, COMP_CSR_UPDATE_PARAMETERS_MASK, tmpcsr);
/* Initialize the COMP state*/
hcomp->State = HAL_COMP_STATE_READY;
}
return status;
}
/**
* @brief Initializes the COMP according to the specified
* parameters in the COMP_InitTypeDef and create the associated handle.
* @note If the selected comparator is locked, initialization can't be performed.
* To unlock the configuration, perform a system reset.
* @param hcomp: COMP handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_COMP_Init(COMP_HandleTypeDef *hcomp)
{
HAL_StatusTypeDef status = HAL_OK;
uint32_t regshift = COMP_CSR_COMP1_SHIFT;
/* Check the COMP handle allocation and lock status */
if((hcomp == NULL) || ((hcomp->State & COMP_STATE_BIT_LOCK) != RESET))
{
status = HAL_ERROR;
}
else
{
/* Check the parameter */
assert_param(IS_COMP_ALL_INSTANCE(hcomp->Instance));
assert_param(IS_COMP_INVERTINGINPUT(hcomp->Init.InvertingInput));
assert_param(IS_COMP_NONINVERTINGINPUT(hcomp->Init.NonInvertingInput));
assert_param(IS_COMP_OUTPUT(hcomp->Init.Output));
assert_param(IS_COMP_OUTPUTPOL(hcomp->Init.OutputPol));
assert_param(IS_COMP_HYSTERESIS(hcomp->Init.Hysteresis));
assert_param(IS_COMP_MODE(hcomp->Init.Mode));
if(hcomp->Init.NonInvertingInput == COMP_NONINVERTINGINPUT_DAC1SWITCHCLOSED)
{
assert_param(IS_COMP_DAC1SWITCH_INSTANCE(hcomp->Instance));
}
if(hcomp->Init.WindowMode != COMP_WINDOWMODE_DISABLED)
{
assert_param(IS_COMP_WINDOWMODE_INSTANCE(hcomp->Instance));
}
if(hcomp->State == HAL_COMP_STATE_RESET)
{
/* Init SYSCFG and the low level hardware to access comparators */
__SYSCFG_CLK_ENABLE();
HAL_COMP_MspInit(hcomp);
}
/* Set COMP parameters */
/* Set COMPxINSEL bits according to hcomp->Init.InvertingInput value */
/* Set COMPxOUTSEL bits according to hcomp->Init.Output value */
/* Set COMPxPOL bit according to hcomp->Init.OutputPol value */
/* Set COMPxHYST bits according to hcomp->Init.Hysteresis value */
/* Set COMPxMODE bits according to hcomp->Init.Mode value */
if(hcomp->Instance == COMP2)
{
regshift = COMP_CSR_COMP2_SHIFT;
}
MODIFY_REG(COMP->CSR,
(uint32_t)(COMP_CSR_COMPxINSEL | COMP_CSR_COMPxNONINSEL_MASK | \
COMP_CSR_COMPxOUTSEL | COMP_CSR_COMPxPOL | \
COMP_CSR_COMPxHYST | COMP_CSR_COMPxMODE) << regshift,
(hcomp->Init.InvertingInput | \
hcomp->Init.NonInvertingInput | \
hcomp->Init.Output | \
hcomp->Init.OutputPol | \
hcomp->Init.Hysteresis | \
hcomp->Init.Mode) << regshift);
if(hcomp->Init.WindowMode != COMP_WINDOWMODE_DISABLED)
{
COMP->CSR |= COMP_CSR_WNDWEN;
}
/* Initialize the COMP state*/
if(hcomp->State == HAL_COMP_STATE_RESET)
{
hcomp->State = HAL_COMP_STATE_READY;
}
}
return status;
}
/**
* @brief Initialize the COMP according to the specified
* parameters in the COMP_InitTypeDef and initialize the associated handle.
* @note If the selected comparator is locked, initialization can't be performed.
* To unlock the configuration, perform a system reset.
* @param hcomp COMP handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_COMP_Init(COMP_HandleTypeDef *hcomp)
{
uint32_t tmp_csr = 0U;
uint32_t exti_line = 0U;
uint32_t comp_voltage_scaler_not_initialized = 0U;
__IO uint32_t wait_loop_index = 0U;
HAL_StatusTypeDef status = HAL_OK;
/* Check the COMP handle allocation and lock status */
if((hcomp == NULL) || (__HAL_COMP_IS_LOCKED(hcomp)))
{
status = HAL_ERROR;
}
else
{
/* Check the parameters */
assert_param(IS_COMP_ALL_INSTANCE(hcomp->Instance));
assert_param(IS_COMP_INPUT_PLUS(hcomp->Instance, hcomp->Init.NonInvertingInput));
assert_param(IS_COMP_INPUT_MINUS(hcomp->Instance, hcomp->Init.InvertingInput));
assert_param(IS_COMP_OUTPUTPOL(hcomp->Init.OutputPol));
assert_param(IS_COMP_POWERMODE(hcomp->Init.Mode));
assert_param(IS_COMP_HYSTERESIS(hcomp->Init.Hysteresis));
assert_param(IS_COMP_BLANKINGSRC_INSTANCE(hcomp->Instance, hcomp->Init.BlankingSrce));
assert_param(IS_COMP_TRIGGERMODE(hcomp->Init.TriggerMode));
assert_param(IS_COMP_WINDOWMODE(hcomp->Init.WindowMode));
if(hcomp->State == HAL_COMP_STATE_RESET)
{
/* Allocate lock resource and initialize it */
hcomp->Lock = HAL_UNLOCKED;
/* Init SYSCFG and the low level hardware to access comparators */
/* Note: HAL_COMP_Init() calls __HAL_RCC_SYSCFG_CLK_ENABLE() */
/* to enable internal control clock of the comparators. */
/* However, this is a legacy strategy. In future STM32 families, */
/* COMP clock enable must be implemented by user */
/* in "HAL_COMP_MspInit()". */
/* Therefore, for compatibility anticipation, it is recommended */
/* to implement __HAL_RCC_SYSCFG_CLK_ENABLE() */
/* in "HAL_COMP_MspInit()". */
__HAL_RCC_SYSCFG_CLK_ENABLE();
/* Init the low level hardware */
HAL_COMP_MspInit(hcomp);
}
/* Memorize voltage scaler state before initialization */
comp_voltage_scaler_not_initialized = (READ_BIT(hcomp->Instance->CSR, COMP_CSR_SCALEN) == 0);
/* Set COMP parameters */
tmp_csr = ( hcomp->Init.NonInvertingInput
| hcomp->Init.InvertingInput
| hcomp->Init.BlankingSrce
| hcomp->Init.Hysteresis
| hcomp->Init.OutputPol
| hcomp->Init.Mode
);
/* Set parameters in COMP register */
/* Note: Update all bits except read-only, lock and enable bits */
#if defined (COMP_CSR_INMESEL)
MODIFY_REG(hcomp->Instance->CSR,
COMP_CSR_PWRMODE | COMP_CSR_INMSEL | COMP_CSR_INPSEL |
COMP_CSR_WINMODE | COMP_CSR_POLARITY | COMP_CSR_HYST |
COMP_CSR_BLANKING | COMP_CSR_BRGEN | COMP_CSR_SCALEN | COMP_CSR_INMESEL,
tmp_csr
);
#else
MODIFY_REG(hcomp->Instance->CSR,
COMP_CSR_PWRMODE | COMP_CSR_INMSEL | COMP_CSR_INPSEL |
COMP_CSR_WINMODE | COMP_CSR_POLARITY | COMP_CSR_HYST |
COMP_CSR_BLANKING | COMP_CSR_BRGEN | COMP_CSR_SCALEN,
tmp_csr
);
#endif
/* Set window mode */
/* Note: Window mode bit is located into 1 out of the 2 pairs of COMP */
/* instances. Therefore, this function can update another COMP */
/* instance that the one currently selected. */
if(hcomp->Init.WindowMode == COMP_WINDOWMODE_COMP1_INPUT_PLUS_COMMON)
{
SET_BIT(COMP12_COMMON->CSR, COMP_CSR_WINMODE);
}
else
{
CLEAR_BIT(COMP12_COMMON->CSR, COMP_CSR_WINMODE);
}
/* Delay for COMP scaler bridge voltage stabilization */
/* Apply the delay if voltage scaler bridge is enabled for the first time */
if ((READ_BIT(hcomp->Instance->CSR, COMP_CSR_SCALEN) != 0U) &&
(comp_voltage_scaler_not_initialized != 0U) )
{
/* Wait loop initialization and execution */
/* Note: Variable divided by 2 to compensate partially */
/* CPU processing cycles. */
wait_loop_index = (COMP_DELAY_VOLTAGE_SCALER_STAB_US * (SystemCoreClock / (1000000 * 2U)));
while(wait_loop_index != 0U)
{
wait_loop_index--;
}
}
/* Get the EXTI line corresponding to the selected COMP instance */
exti_line = COMP_GET_EXTI_LINE(hcomp->Instance);
/* Manage EXTI settings */
if((hcomp->Init.TriggerMode & (COMP_EXTI_IT | COMP_EXTI_EVENT)) != RESET)
{
/* Configure EXTI rising edge */
if((hcomp->Init.TriggerMode & COMP_EXTI_RISING) != RESET)
{
LL_EXTI_EnableRisingTrig_0_31(exti_line);
}
else
{
LL_EXTI_DisableRisingTrig_0_31(exti_line);
}
/* Configure EXTI falling edge */
if((hcomp->Init.TriggerMode & COMP_EXTI_FALLING) != RESET)
{
LL_EXTI_EnableFallingTrig_0_31(exti_line);
}
else
{
LL_EXTI_DisableFallingTrig_0_31(exti_line);
}
/* Clear COMP EXTI pending bit (if any) */
LL_EXTI_ClearFlag_0_31(exti_line);
/* Configure EXTI event mode */
if((hcomp->Init.TriggerMode & COMP_EXTI_EVENT) != RESET)
{
LL_EXTI_EnableEvent_0_31(exti_line);
}
else
{
LL_EXTI_DisableEvent_0_31(exti_line);
}
/* Configure EXTI interrupt mode */
if((hcomp->Init.TriggerMode & COMP_EXTI_IT) != RESET)
{
LL_EXTI_EnableIT_0_31(exti_line);
}
else
{
LL_EXTI_DisableIT_0_31(exti_line);
}
}
else
{
/* Disable EXTI event mode */
LL_EXTI_DisableEvent_0_31(exti_line);
/* Disable EXTI interrupt mode */
LL_EXTI_DisableIT_0_31(exti_line);
}
/* Set HAL COMP handle state */
/* Note: Transition from state reset to state ready, */
/* otherwise (coming from state ready or busy) no state update. */
if (hcomp->State == HAL_COMP_STATE_RESET)
{
hcomp->State = HAL_COMP_STATE_READY;
}
}
return status;
}
