/**
* @brief Initialize the EXTI registers according to the specified parameters in EXTI_InitStruct.
* @param EXTI_InitStruct pointer to a @ref LL_EXTI_InitTypeDef structure.
* @retval An ErrorStatus enumeration value:
* - SUCCESS: EXTI registers are initialized
* - ERROR: not applicable
*/
uint32_t LL_EXTI_Init(LL_EXTI_InitTypeDef *EXTI_InitStruct)
{
ErrorStatus status = SUCCESS;
/* Check the parameters */
assert_param(IS_LL_EXTI_LINE_0_31(EXTI_InitStruct->Line_0_31));
assert_param(IS_FUNCTIONAL_STATE(EXTI_InitStruct->LineCommand));
assert_param(IS_LL_EXTI_MODE(EXTI_InitStruct->Mode));
/* ENABLE LineCommand */
if (EXTI_InitStruct->LineCommand != DISABLE)
{
assert_param(IS_LL_EXTI_TRIGGER(EXTI_InitStruct->Trigger));
/* Configure EXTI Lines in range from 0 to 31 */
if (EXTI_InitStruct->Line_0_31 != LL_EXTI_LINE_NONE)
{
switch (EXTI_InitStruct->Mode)
{
case LL_EXTI_MODE_IT:
/* First Disable Event on provided Lines */
LL_EXTI_DisableEvent_0_31(EXTI_InitStruct->Line_0_31);
/* Then Enable IT on provided Lines */
LL_EXTI_EnableIT_0_31(EXTI_InitStruct->Line_0_31);
break;
case LL_EXTI_MODE_EVENT:
/* First Disable IT on provided Lines */
LL_EXTI_DisableIT_0_31(EXTI_InitStruct->Line_0_31);
/* Then Enable Event on provided Lines */
LL_EXTI_EnableEvent_0_31(EXTI_InitStruct->Line_0_31);
break;
case LL_EXTI_MODE_IT_EVENT:
/* Directly Enable IT & Event on provided Lines */
LL_EXTI_EnableIT_0_31(EXTI_InitStruct->Line_0_31);
LL_EXTI_EnableEvent_0_31(EXTI_InitStruct->Line_0_31);
break;
default:
status = ERROR;
break;
}
if (EXTI_InitStruct->Trigger != LL_EXTI_TRIGGER_NONE)
{
switch (EXTI_InitStruct->Trigger)
{
case LL_EXTI_TRIGGER_RISING:
/* First Disable Falling Trigger on provided Lines */
LL_EXTI_DisableFallingTrig_0_31(EXTI_InitStruct->Line_0_31);
/* Then Enable Rising Trigger on provided Lines */
LL_EXTI_EnableRisingTrig_0_31(EXTI_InitStruct->Line_0_31);
break;
case LL_EXTI_TRIGGER_FALLING:
/* First Disable Rising Trigger on provided Lines */
LL_EXTI_DisableRisingTrig_0_31(EXTI_InitStruct->Line_0_31);
/* Then Enable Falling Trigger on provided Lines */
LL_EXTI_EnableFallingTrig_0_31(EXTI_InitStruct->Line_0_31);
break;
case LL_EXTI_TRIGGER_RISING_FALLING:
LL_EXTI_EnableRisingTrig_0_31(EXTI_InitStruct->Line_0_31);
LL_EXTI_EnableFallingTrig_0_31(EXTI_InitStruct->Line_0_31);
break;
default:
status = ERROR;
break;
}
}
}
}
/* DISABLE LineCommand */
else
{
/* De-configure EXTI Lines in range from 0 to 31 */
LL_EXTI_DisableIT_0_31(EXTI_InitStruct->Line_0_31);
LL_EXTI_DisableEvent_0_31(EXTI_InitStruct->Line_0_31);
}
return status;
}
/**
* @brief Initialize the COMP according to the specified
* parameters in the COMP_InitTypeDef and initialize the associated handle.
* @note If the selected comparator is locked, initialization can't be performed.
* To unlock the configuration, perform a system reset.
* @param hcomp COMP handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_COMP_Init(COMP_HandleTypeDef *hcomp)
{
uint32_t tmp_csr = 0U;
uint32_t exti_line = 0U;
uint32_t comp_voltage_scaler_not_initialized = 0U;
__IO uint32_t wait_loop_index = 0U;
HAL_StatusTypeDef status = HAL_OK;
/* Check the COMP handle allocation and lock status */
if((hcomp == NULL) || (__HAL_COMP_IS_LOCKED(hcomp)))
{
status = HAL_ERROR;
}
else
{
/* Check the parameters */
assert_param(IS_COMP_ALL_INSTANCE(hcomp->Instance));
assert_param(IS_COMP_INPUT_PLUS(hcomp->Instance, hcomp->Init.NonInvertingInput));
assert_param(IS_COMP_INPUT_MINUS(hcomp->Instance, hcomp->Init.InvertingInput));
assert_param(IS_COMP_OUTPUTPOL(hcomp->Init.OutputPol));
assert_param(IS_COMP_POWERMODE(hcomp->Init.Mode));
assert_param(IS_COMP_HYSTERESIS(hcomp->Init.Hysteresis));
assert_param(IS_COMP_BLANKINGSRC_INSTANCE(hcomp->Instance, hcomp->Init.BlankingSrce));
assert_param(IS_COMP_TRIGGERMODE(hcomp->Init.TriggerMode));
assert_param(IS_COMP_WINDOWMODE(hcomp->Init.WindowMode));
if(hcomp->State == HAL_COMP_STATE_RESET)
{
/* Allocate lock resource and initialize it */
hcomp->Lock = HAL_UNLOCKED;
/* Init SYSCFG and the low level hardware to access comparators */
/* Note: HAL_COMP_Init() calls __HAL_RCC_SYSCFG_CLK_ENABLE() */
/* to enable internal control clock of the comparators. */
/* However, this is a legacy strategy. In future STM32 families, */
/* COMP clock enable must be implemented by user */
/* in "HAL_COMP_MspInit()". */
/* Therefore, for compatibility anticipation, it is recommended */
/* to implement __HAL_RCC_SYSCFG_CLK_ENABLE() */
/* in "HAL_COMP_MspInit()". */
__HAL_RCC_SYSCFG_CLK_ENABLE();
/* Init the low level hardware */
HAL_COMP_MspInit(hcomp);
}
/* Memorize voltage scaler state before initialization */
comp_voltage_scaler_not_initialized = (READ_BIT(hcomp->Instance->CSR, COMP_CSR_SCALEN) == 0);
/* Set COMP parameters */
tmp_csr = ( hcomp->Init.NonInvertingInput
| hcomp->Init.InvertingInput
| hcomp->Init.BlankingSrce
| hcomp->Init.Hysteresis
| hcomp->Init.OutputPol
| hcomp->Init.Mode
);
/* Set parameters in COMP register */
/* Note: Update all bits except read-only, lock and enable bits */
#if defined (COMP_CSR_INMESEL)
MODIFY_REG(hcomp->Instance->CSR,
COMP_CSR_PWRMODE | COMP_CSR_INMSEL | COMP_CSR_INPSEL |
COMP_CSR_WINMODE | COMP_CSR_POLARITY | COMP_CSR_HYST |
COMP_CSR_BLANKING | COMP_CSR_BRGEN | COMP_CSR_SCALEN | COMP_CSR_INMESEL,
tmp_csr
);
#else
MODIFY_REG(hcomp->Instance->CSR,
COMP_CSR_PWRMODE | COMP_CSR_INMSEL | COMP_CSR_INPSEL |
COMP_CSR_WINMODE | COMP_CSR_POLARITY | COMP_CSR_HYST |
COMP_CSR_BLANKING | COMP_CSR_BRGEN | COMP_CSR_SCALEN,
tmp_csr
);
#endif
/* Set window mode */
/* Note: Window mode bit is located into 1 out of the 2 pairs of COMP */
/* instances. Therefore, this function can update another COMP */
/* instance that the one currently selected. */
if(hcomp->Init.WindowMode == COMP_WINDOWMODE_COMP1_INPUT_PLUS_COMMON)
{
SET_BIT(COMP12_COMMON->CSR, COMP_CSR_WINMODE);
}
else
{
CLEAR_BIT(COMP12_COMMON->CSR, COMP_CSR_WINMODE);
}
/* Delay for COMP scaler bridge voltage stabilization */
/* Apply the delay if voltage scaler bridge is enabled for the first time */
if ((READ_BIT(hcomp->Instance->CSR, COMP_CSR_SCALEN) != 0U) &&
(comp_voltage_scaler_not_initialized != 0U) )
{
/* Wait loop initialization and execution */
/* Note: Variable divided by 2 to compensate partially */
/* CPU processing cycles. */
wait_loop_index = (COMP_DELAY_VOLTAGE_SCALER_STAB_US * (SystemCoreClock / (1000000 * 2U)));
while(wait_loop_index != 0U)
{
wait_loop_index--;
}
}
/* Get the EXTI line corresponding to the selected COMP instance */
exti_line = COMP_GET_EXTI_LINE(hcomp->Instance);
/* Manage EXTI settings */
if((hcomp->Init.TriggerMode & (COMP_EXTI_IT | COMP_EXTI_EVENT)) != RESET)
{
/* Configure EXTI rising edge */
if((hcomp->Init.TriggerMode & COMP_EXTI_RISING) != RESET)
{
LL_EXTI_EnableRisingTrig_0_31(exti_line);
}
else
{
LL_EXTI_DisableRisingTrig_0_31(exti_line);
}
/* Configure EXTI falling edge */
if((hcomp->Init.TriggerMode & COMP_EXTI_FALLING) != RESET)
{
LL_EXTI_EnableFallingTrig_0_31(exti_line);
}
else
{
LL_EXTI_DisableFallingTrig_0_31(exti_line);
}
/* Clear COMP EXTI pending bit (if any) */
LL_EXTI_ClearFlag_0_31(exti_line);
/* Configure EXTI event mode */
if((hcomp->Init.TriggerMode & COMP_EXTI_EVENT) != RESET)
{
LL_EXTI_EnableEvent_0_31(exti_line);
}
else
{
LL_EXTI_DisableEvent_0_31(exti_line);
}
/* Configure EXTI interrupt mode */
if((hcomp->Init.TriggerMode & COMP_EXTI_IT) != RESET)
{
LL_EXTI_EnableIT_0_31(exti_line);
}
else
{
LL_EXTI_DisableIT_0_31(exti_line);
}
}
else
{
/* Disable EXTI event mode */
LL_EXTI_DisableEvent_0_31(exti_line);
/* Disable EXTI interrupt mode */
LL_EXTI_DisableIT_0_31(exti_line);
}
/* Set HAL COMP handle state */
/* Note: Transition from state reset to state ready, */
/* otherwise (coming from state ready or busy) no state update. */
if (hcomp->State == HAL_COMP_STATE_RESET)
{
hcomp->State = HAL_COMP_STATE_READY;
}
}
return status;
}
