///////////////////////////////////////////////////////////////////////////////////////
//
// 模型参数调节菜单处理过程
//
u32 PageDeltaSet(u8 event)
{
static MENUSTAT ms;
if(event==PV_INIT)
{
LcdClear(0);
if(!ms.Init)
{
ms.iFocus=ms.iStart=0;
ms.Init=1;
}
ms.Param=0xff;
ms.Total=MenuDeltaSet[0].Max;
ms.DrawMask=PD_ALL;
return 1;
}
//根据使能开关确定菜单数
if(Model.Delta.Enable) ms.Total=MenuDeltaSet[0].Max;
else ms.Total=1;
//菜单数变化重绘
if(ms.Param!=ms.Total)
{
LcdClear(0);
ms.Param=ms.Total;
ms.DrawMask=PD_ALL;
}
if(event==PV_REDRAW)
{
ms.DrawMask=PD_ALL;
}
//菜单通用处理过程
PageMenuProc(MenuDeltaSet,&ms);
//返回键处理
if(KeyTstDown(KEY_EXT))
{
//V尾混控和三角翼/襟副翼混控互斥
if(Model.Delta.Enable)
{
Model.Vtail.Enable=0;
Model.FlpAil.Enable=0;
}
PageReturn(PV_REDRAW);
}
KeyClearDown(KEY_MENUALL);
return 0;
}
void setup() {
Serial.begin(9600);
Serial.println("$CLS#Setup()");
pinMode(RED, OUTPUT);
pinMode(GREEN, OUTPUT);
pinMode(BLUE, OUTPUT);
LcdInit();
WiFi.begin(ssid, pass);
while (WiFi.status() != WL_CONNECTED) {
PulseLed(RED, 2, 10, 10);
PulseLed(BLUE, 2, 10, 10);
PulseLed(GREEN, 2, 10, 10);
Serial.print(".");
LcdPrint(".");
}
Udp.begin(localPort);
setSyncInterval(300);
setSyncProvider(getNtpTime);
// Turn on the backlight.
LcdClear();
LcdnoBacklight();
delay(2000);
LcdBacklight();
}
void LcdInit ( void ) //инициализация SPI и дисплея
{
LCD_PORT.LCD_RST_PIN = 1; //настроили порты ввода/вывода
LCD_DDR.LCD_RST_PIN = LCD_DDR.LCD_DC_PIN = LCD_DDR.LCD_CE_PIN = LCD_DDR.SPI_MOSI_PIN = LCD_DDR.SPI_CLK_PIN = 1;
delay_ms(1);
SPCR = 0x50;
LCD_PORT.LCD_RST_PIN = 0; //дернули ресет
delay_ms(10);
LCD_PORT.LCD_RST_PIN = 1;
//Enable SPI port: No interrupt, MSBit first, Master mode, CPOL->0, CPHA->0, Clk/4
LCD_PORT.LCD_CE_PIN = 1; //Disable LCD controller
LcdSend( 0b00100001, LCD_CMD ); //LCD Extended Commands
LcdSend( 0b00000100+temp_control, LCD_CMD ); //Set Temp coefficent
#ifdef china
LcdSend( 0b00001000|SPI_invert<<3, LCD_CMD ); //порядок битов в SPI
#endif
LcdSend( 0b00010000+bias, LCD_CMD ); //LCD bias mode 1:48
#ifdef china
LcdSend( 0b01000000+shift, LCD_CMD ); //первая строка выше экрана, отображаем со второй
#endif
LcdSend( 0b10000000+Vop, LCD_CMD ); //Set LCD Vop (Contrast)
#ifdef china
LcdSend( 0x20|x_mirror<<5|y_mirror<<4|power_down<<3, LCD_CMD ); //LCD Standard Commands
#endif
#ifndef china
LcdSend( 0x20|power_down<<3|addressing<<2, LCD_CMD ); //LCD Standard Commands
#endif
LcdSend( 0b00001000|((disp_config<<1|disp_config)&0b00000101), LCD_CMD ); //LCD mode
LcdClear();
}
///////////////////////////////////////////////////////////////////////////////////////
//
// 陀螺仪菜单处理
//
u32 PageGyroSet(u8 event)
{
static MENUSTAT ms;
if(event==PV_INIT)
{
LcdClear(0);
if(!ms.Init)
{
ms.iFocus=ms.iStart=0;
ms.Init=1;
}
ms.Total=MenuGyroSet[0].Max;
ms.DrawMask=PD_ALL;
return 1;
}
if(event==PV_REDRAW)
{
ms.DrawMask=PD_ALL;
}
//菜单通用处理过程
PageMenuProc(MenuGyroSet,&ms);
//返回键处理
if(KeyTstDown(KEY_EXT))
{
PageReturn(PV_REDRAW);
}
KeyClearDown(KEY_MENUALL);
return 0;
}
void enter_graphic_menu(uint8_t menu_no, uint8_t submenu_no)
{
char s[20];
LcdFillLine(1);
slide_down(); // animacja
LcdClear();
if(menu_no==0 && submenu_no==2) // Menu 1.2
{
LcdRectangle(0, 0, 83, 47,TRANSPARENT); // ramka
rez=enter_integer(rez,-10,100,2,3, "WART." , "s"); // funkcja obslugi danej pozycji menu
}
LcdRectangle(0, 0, 83, 47,TRANSPARENT); // przykladowy kod po powrocie z funkcji obslugi menu
LcdClearArea(3,2,13);
LcdGotoXY(2,3);
sprintf(s,"MENU %1u.%1u:%d",menu_no + 1, submenu_no, rez);
LcdStr(FONT_1X, FONT_POSITIVE, (unsigned char*)s);
delay_ms(1000);
LcdFillLine(1); // powrot do menu
LcdGotoXY(2,1);
slide_up(); // animacja
LcdStr(FONT_1X,FONT_NEGATIVE,"MENU");
slide_down(); // animacja
show_graphic_menu(menu_item,submenu_item); // pokazanie menu
}
///////////////////////////////////////////////////////////////////////////////////////
//
// 模型参数调节菜单处理过程
//
u32 PageAeroSet(u8 event)
{
static MENUSTAT ms;
if(event==PV_INIT)
{
LcdClear(0);
if(!ms.Init)
{
ms.iFocus=ms.iStart=0;
ms.Init=1;
}
ms.Total=MenuAeroSet[0].Max;
ms.DrawMask=PD_ALL;
return 1;
}
if(event==PV_REDRAW)
{
ms.DrawMask=PD_ALL;
}
//菜单通用处理过程
PageMenuProc(MenuAeroSet,&ms);
//回车键处理
if(KeyTstDown(KEY_ENT))
{
//如果有子菜单或子功能，进入
if(MenuAeroSet[ms.iFocus+1].SubItem)
{
if(MenuAeroSet[ms.iFocus+1].SubItem==PageCurveSet)
{
PageCurveCnt =MenuAeroSet[ms.iFocus+1].Max;
if(MenuAeroSet[ms.iFocus+1].Min==1)
{
PageCurveTitle =PageStkCurveTitle;
PageCurveValue =&Model.StkCurve[0][0][0];
}
else
{
PageCurveTitle =PageThrCurveTitle;
PageCurveValue =&Model.ThrCurve[0][0];
}
}
BeepMusic(MusicEnter);
PageEnter((PAGEPROC)MenuAeroSet[ms.iFocus+1].SubItem,PV_INIT);
}
}
//返回键处理
if(KeyTstDown(KEY_EXT))
{
PageReturn(PV_REDRAW);
}
KeyClearDown(KEY_MENUALL);
return 0;
}
void PCD8544::begin()
{
pinMode(pin_sce, OUTPUT);
pinMode(pin_rst, OUTPUT);
pinMode(pin_dc, OUTPUT);
pinMode(pin_sdin, OUTPUT);
pinMode(pin_sclk, OUTPUT);
//reset display
digitalWrite(pin_rst, LOW);
digitalWrite(pin_rst, HIGH);
//Init
LcdWrite( LCD_CMD, 0x21 ); // LCD Extended Commands.
LcdWrite( LCD_CMD, 0xB0 ); // Set LCD Vop (Contrast). //B1
LcdWrite( LCD_CMD, 0x04 ); // Set Temp coefficent. //0x04
LcdWrite( LCD_CMD, 0x14 ); // LCD bias mode 1:48. //0x13
//We must send 0x20 before modifying the display control mode
LcdWrite( LCD_CMD, 0x20 );
LcdWrite( LCD_CMD, 0x0C ); // LCD in normal mode 0x0c. 0x0d for inverse
//backlight
pinMode(pin_blight, OUTPUT);
analogWrite(pin_blight, 255);
LcdClear();
}
//inicjalizacja sterownika
void LcdInit(void)
{
int i;
HAL_GPIO_WritePin(PORT_DISP_NOKIA,LCD_PWR,GPIO_PIN_RESET);
HAL_GPIO_WritePin(PORT_DISP_NOKIA,LCD_BKLT,GPIO_PIN_RESET);
delay_ms(500);
HAL_GPIO_WritePin(PORT_DISP_NOKIA,LCD_BKLT,GPIO_PIN_SET);
HAL_GPIO_WritePin(PORT_DISP_NOKIA,LCD_PWR,GPIO_PIN_SET);
HAL_GPIO_WritePin(PORT_DISP_NOKIA,RES,GPIO_PIN_RESET);
delay_ms(2);
HAL_GPIO_WritePin(PORT_DISP_NOKIA,RES,GPIO_PIN_SET);
WriteCmd(0x21);//komendy rozszerzone
WriteCmd(0x05);//komenda „przelaczajaca” sterownik w tryb pracy zgodny PCD8544
WriteCmd(0xd5);//ustawienie Vop
Delay(2);
//WriteCmd(0x13);//bias
WriteCmd(0x06);//korekcja temperatury dla PCD8544
WriteCmd(0x14);//wspólczynnik multipleksowania
WriteCmd(0x20);//komendy standardowe - adresowanie poziome
Delay(2);
WriteCmd(0x0c);//tryb wyœwietlania Standard Mode
WriteCmd(0x40);//zerowanie licznika wierszy
WriteCmd(0x80);//zerowanie licznika kolumn
Delay(2);
// for(i=0;i<(48*84);i++)//612
// WriteData(0x00);//zerowanie pamieci RAM wyswietlacza
LoWaterMark = LCD_CACHE_SIZE;
HiWaterMark = 0;
LcdClear();
LcdUpdate();
}
/*****************************************************
* INITIALIZE DISPLAY
* DESCRIPTION: Setup all ports and initialize the LCD
* for usage.
*****************************************************/
void InitializeNokia5110(void)
{
P2DIR |= 0x10; //Set LCD power port
P2OUT |= 0x10; //Power up LCD
P2DIR |= PIN_SCE;
P2DIR |= PIN_RESET;
P1DIR |= PIN_DC;
P1DIR |= PIN_LED;
P1OUT&= ~PIN_LED; //Enable the backlight by default
P1SEL = BIT1 + BIT2 + BIT4;
P1SEL2 = BIT1 + BIT2 + BIT4;
UCA0CTL0 |= UCCKPL + UCMSB + UCMST + UCSYNC; // 3-pin, 8-bit SPI master
UCA0CTL1 |= UCSSEL_2; // SMCLK
UCA0BR0 |= 2; // /2
UCA0BR1 = 0; //
UCA0MCTL = 0; // No modulation
UCA0CTL1 &= ~UCSWRST; // **Initialize USCI state machine**
digitalWrite(PIN_RESET, 0);
digitalWrite(PIN_RESET, 1);
//Send LCD init instructions
LcdCommand(0x21 ); // LCD Extended Commands.
LcdCommand(0xB6 ); // Set LCD Vop (Contrast).0xB0
LcdCommand(0x04 ); // Set Temp coefficent. //0x04
LcdCommand(0x15 ); // LCD bias mode 1:48. //0x13
LcdCommand(0x0C ); // LCD in normal mode.
LcdCommand(0x20 );
LcdCommand(0x0C );
LcdClear();
}
int main(){
int i,j;
LcdInitialise();
LcdClear();
LcdString("Hola");
while (1);
}
int main()
{
LcdInit(); //initialize LCD
LcdContrast(0x7F); //display image
_delay_ms(1000);
LcdClear();
LcdContrast(0x3F); //adjust contrast
_delay_ms(1000);
LcdClear();
LcdImage(waitImage); //wait image
LcdUpdate();
_delay_ms(4000);
ADCSRA |= (1<<ADEN)|(1<<ADPS0)|(1<<ADPS1)|(1<<ADPS2); //enable ADC and select clk/128
ADMUX |= (1<<REFS0)|(1<<ADLAR); //Vref, ADC0 as input
DDRC = 0x00;
uint16_t temp, temp1, temp2, temp3;
while (1)
{
ADCSRA |= (1<<ADSC); //begin conversion
while(!(ADCSRA &(1<<ADSC))==0); //wait for end of conversion
temp=(ADCH<<8)|ADCL;
//calculation for temperature
temp1 = temp%10;
temp2 = temp%100/10;
temp3 = temp%1000/100;
char digit[4];
sprintf(digit, "%d%d.%d ", temp1, temp2, temp3); //display temperature
LcdClear();
LcdGotoXYFont(1,1);
LcdFStr(FONT_1X,(unsigned char*)digit);
LcdGotoXYFont(1,2);
LcdFStr(FONT_1X,(unsigned char*)PSTR ("Fahrenheit"));
LcdUpdate();
_delay_ms(1000);
}
return 0;
}
void exit_from_menu(void)
{
LcdClear();
LcdFillLine(1);
LcdGotoXY(1,1);
LcdStr(FONT_1X,FONT_NEGATIVE," LCD DEMO ");
LcdFillLine(6);
LcdGotoXY(1,6);
LcdStr(FONT_1X,FONT_NEGATIVE," LCD DEMO ");}
int main(void)
{
RCC->CFGR |= (RCC_CFGR_HPRE_1|RCC_CFGR_HPRE_3); /* div 8 */
LcdInit();
LcdClear();
LcdChr ( Y_POSITION*1+X_POSITION*1+13, "Hello world" );
LcdChr ( Y_POSITION*2+X_POSITION*1+13+INVERSE+X_OFFSET*3, "Hello world" );
LcdChr ( Y_POSITION*4+X_POSITION*0+2+BIG_UP, "15" );
LcdChr ( Y_POSITION*5+X_POSITION*0+2+BIG_DOWN, "15" );
return 0;
}
static void lcdPrint(char *line){
int i;
/*
* Show welcome message in LCD-display
*/
LcdSetCursor(0);
LcdClear();
for (i = 0; i < strlen(line); i++) {
LcdSetCursor(i);
LcdWriteData(line[i]);
}
}
void setup() {
// set up the encoder interrupt to detect falling edge on digital pin 2
attachInterrupt(0, encoder_interrupt, FALLING);
Serial.begin(115200);
Serial.write("<h>time\tspeed\tcurrent\tcurrent_sense\tvoltage\tvoltage_sense</h>\n");
Serial.write("<u>ms\trpm\tmA\tcounts\tvolts\tcts</u>\n");
pinMode(LED_PWM_PIN, OUTPUT);
pinMode(VOLT_PIN, INPUT);
pinMode(INTERRUPTER_PIN, INPUT);
pinMode(LED_PIN, OUTPUT);
pinMode(BTN_PIN, INPUT);
LcdInitialize();
gotoXY(0,0);
LcdClear();
LcdString((char*)"Current:");
gotoXY(0,2);
LcdString((char*)"Speed:");
gotoXY(0,4);
LcdString((char*)"Voltage:");
blink_clock = millis();
tach_enc.min_hertz = 5;
tach_enc.max_period = 5000;
tach_enc.pin_num = INTERRUPTER_PIN;
tach_enc.debounce_min = 5;
tach_enc.alpha = 800;
tach_enc.cts_per_rev = 1;
tach_enc.hertz = 0;
button.button_pin = BTN_PIN;
button.button_state = btnDown;
// pulser.carrier_clock = 0;
// pulser.carrier_period = 5000;
// pulser.step_clock = 0;
// pulser.pulse_up_period = 1000;
// pulser.pulse_down_period = 3500;
// pulser.step_period_up = pulser.pulse_up_period / impulse_num_samples;
// pulser.step_period_down = pulser.pulse_down_period / impulse_num_samples;
// pulser.index = 0;
// pulser.offset_time = 0; // start pulse at beginning of each carrier period
volt_sensor.max_volts = 68000; // mV at sensor saturation (depends on pot adj)
// init_impulse(impulse_array, impulse_num_samples, 255);
}
//
// Send all the required initialization commands to the display
//
void LcdInit(void) {
LcdSend(LCD_C, 0xE2); // Software Reset
delay(1);
LcdSend(LCD_C, 0x3D); // Charge pump ON
LcdSend(LCD_C, 0x01); // Charge pump=4
LcdSend(LCD_C, 0xA4); // Display all points = OFF
LcdSend(LCD_C, 0x2F); // Booster=ON, Voltage Reg=ON, Voltage Follower=ON
LcdSend(LCD_C, 0xAF); // Display ON
LcdSend(LCD_C, 0xA6); // Normal display
LcdSend(LCD_C, 0xC0); // Normal screen up/down
LcdSend(LCD_C, 0xA0); // Normal screen left/right
LcdClear();
}
/***********************************************************
* SHOW JET SCORE
* DESCRIPTION: Shows the current stats of the game.
***********************************************************/
void showPongScore(unsigned int player, unsigned int computer, unsigned int highScore)
{
LcdClear();
printf_5Words("Plyr: ", "Cmp: ", "High: ", "", "", 10);
set_LCD_Cursor(30, 0);
printf_int(player);
set_LCD_Cursor(30, 1);
printf_int(computer);
set_LCD_Cursor(30, 2);
printf_int(highScore);
WaitUserInput();
}
void exit_from_graphic_menu()
{
uint8_t i;
slide_up(); // animacja
LcdClear(); // powrot do trybu normalnego
LcdFillLine(1);
LcdGotoXY(1,1);
LcdStr(FONT_1X,FONT_NEGATIVE," LCD DEMO ");
LcdFillLine(6);
LcdGotoXY(1,6);
LcdStr(FONT_1X,FONT_NEGATIVE," LCD DEMO ");
}
///////////////////////////////////////////////////////////////////////////////////////
//
// 混控菜单处理过程
//
u32 PageMixerSet(u8 event)
{
static MENUSTAT ms;
if(event==PV_INIT)
{
LcdClear(0);
if(!ms.Init)
{
ms.iFocus=ms.iStart=0;
ms.Init=1;
}
ms.Total=MenuMixerSet[0].Max;
ms.DrawMask=PD_ALL;
return 1;
}
if(event==PV_REDRAW)
{
ms.DrawMask=PD_ALL;
}
//设置各混控状态
strcpy(MenuMixerVtailStat,PageOptionOnOff[Model.Vtail.Enable]);
strcpy(MenuMixerDeltaStat,PageOptionOnOff[Model.Delta.Enable]);
strcpy(MenuMixerFlpAilStat,PageOptionOnOff[Model.FlpAil.Enable]);
//菜单通用处理过程
PageMenuProc(MenuMixerSet,&ms);
//回车键处理
if(KeyTstDown(KEY_ENT))
{
//如果有子菜单或子功能，进入
if(MenuMixerSet[ms.iFocus+1].SubItem)
{
BeepMusic(MusicEnter);
PageEnter((PAGEPROC)MenuMixerSet[ms.iFocus+1].SubItem,PV_INIT);
}
}
//返回键处理
if(KeyTstDown(KEY_EXT))
{
PageReturn(PV_REDRAW);
}
KeyClearDown(KEY_MENUALL);
return 0;
}
void LcdInitialise(void)
{
DATAPORT &= NOT_PIN_RESET; //digitalWrite(PIN_RESET, LOW);
DATAPORT |= PIN_RESET; //digitalWrite(PIN_RESET, HIGH);
LcdWriteInit(0x21); // LCD Extended Commands.
LcdWriteInit(0xB1); // Set LCD Vop (Contrast).
LcdWriteInit(0x04); // Set Temp coefficent. //0x04
LcdWriteInit(0x14); // LCD bias mode 1:48. //0x13
LcdWriteInit(0x20); // LCD Basic Commands
LcdWriteInit(0x0C); // LCD in normal mode.
LcdInitBuffer();
LcdClear();
}
/***********************************************************
* SHOW JET SCORE
* DESCRIPTION: Shows the current stats of the game.
***********************************************************/
void showJetScore(unsigned int ballsDestroyed, unsigned int health, unsigned int highScore)
{
LcdClear();
printf_5Words("Hit: ", "Hlth: ", "High: ", "", "", 10);
set_LCD_Cursor(30, 0);
printf_int(ballsDestroyed);
set_LCD_Cursor(30, 1);
printf_int(health);
set_LCD_Cursor(30, 2);
printf_int(highScore);
StartTimer(0, 200);
WaitUserInput();
}
void setDisplay(){
if (modechanged){
gotoXY(0,0);
sprintf(cha, " Ustaw. wysw.");LcdString(cha, true);
gotoXY(0,1);
sprintf(cha, EMPTY_LINE);LcdString(cha, false);
}
gotoXY(0,1);
sprintf(cha, "kontrast:");LcdString(cha,false);
gotoXY(60,1);
sprintf(cha, "%02i", contrast_val);LcdString(cha, (pos_setDisp==0));
gotoXY(0,2);
sprintf(cha, "jasnosc:");LcdString(cha,false);
gotoXY(60,2);
sprintf(cha, "%02i", jasnosc_val);LcdString(cha, (pos_setDisp==1));
gotoXY(0,3);
sprintf(cha, "OK");LcdString(cha,(pos_setDisp==2));
if (modechanged){
gotoXY(0,4);
sprintf(cha, "<> poprz/nast");LcdString(cha);
gotoXY(0,5);
sprintf(cha, "^v wart +/-");LcdString(cha);
modechanged=false;
}
if (pos_setDisp==0){
if (isUp()) { contrast_val=obetnij(contrast_val+1, 10, true); LcdInitialise(); }
if (isDown()) { contrast_val=obetnij(contrast_val-1, 10, true); LcdInitialise(); }
}
else if (pos_setDisp==1){
if (isUp()) { jasnosc_val=obetnij(jasnosc_val+1, 50); analogWrite(11, jasnosc_val); }
if (isDown()) { jasnosc_val=obetnij(jasnosc_val-1, 50); analogWrite(11, jasnosc_val); }
}
if (pos_setDisp==2){
if (isPressed()) {
mode=1;
modechanged=true;
LcdClear();
return;
}
}
if (isRight()) pos_setDisp++;
if (isLeft()) pos_setDisp--;
if (pos_setDisp>2) pos_setDisp=0;
if (pos_setDisp<0) pos_setDisp=2;
}
void SysInit(void)
{
WDTCTL = WDTPW | WDTHOLD; // Stop watchdog timer
Board_init(); // Basic GPIO initialization
SetVCore(3); // Set Vcore to accomodate for max. allowed system speed
LFXT_Start(XT1DRIVE_0); // Use 32.768kHz XTAL as reference, ACLK: SELA = 000, DIVA = 000
Init_FLL_Settle(25000, 762); // Set system clock to max (25MHz)
LcdInit();
LcdClear();
//display_rect();
AD9954Init();
P4SEL = 0x00;
P4DIR = 0x00;
P4REN = 0xff;
}
void MainMenu()
{
if ( Event == 0 )
return;
if ( Event == EV_FUNC_FIRST )
{
MenuCounter = 0;
LcdClear();
goto RedrawMenu;
}
if ( (Event & EV_MASK) == EV_KEY_PRESSED )
{
switch (Event & KEY_MASK)
{
case KEY_UP:
if ( MenuCounter == 0 )
MenuCounter = 6;
else
MenuCounter = MenuCounter - 1;
break;
case KEY_DOWN:
if ( MenuCounter == 6 )
MenuCounter = 0;
else
MenuCounter = MenuCounter + 1;
break;
case KEY_ENTER:
switch(MenuCounter)
{
case 4: // Установка контрастности
CurrentFunc(Contrast);
break;
case 5:
// GPIO_TOGGLE(LCD_LED);
break;
case 6:
// GPIO_RESET(PWR_ON);
break;
default:
CurrentFunc(MenuSelected;)
return;
}
}
}
static int LcdInit(NUTDEVICE * dev)
{
LCD_RS_CLR();
LCD_RW_CLR();
LcdClrBits(LCD_DATA);
NutMicroDelay(30);
LCD_EN_CLR();
NutMicroDelay(30);
NutSleep(18);
/* This initialization will make sure, that the LCD is switched
* to 8-bit mode, no matter which mode we start from or we finally
* need.
*/
LcdWriteCmd(_BV(LCD_FUNCTION) | _BV(LCD_FUNCTION_8BIT));
NutSleep(16);
LcdWriteCmd(_BV(LCD_FUNCTION) | _BV(LCD_FUNCTION_8BIT));
NutSleep(4);
LcdWriteCmd(_BV(LCD_FUNCTION) | _BV(LCD_FUNCTION_8BIT));
NutSleep(2);
LcdWriteInstruction((_BV(LCD_FUNCTION)) | (_BV(LCD_FUNCTION_8BIT)) | (_BV(LCD_EXT)) , LCD_SHORT_DELAY);
/* Switch display and cursor off. */
LcdWriteNibble(_BV(LCD_ON_CTRL) >> 4);
LcdWriteNibble(_BV(LCD_ON_CTRL));
NutSleep(2);
/* Clear display. */
LcdClear();
/* Set entry mode. */
LcdWriteCmd(_BV(LCD_ENTRY_MODE) | _BV(LCD_ENTRY_INC));
/* Switch display on. */
LcdWriteCmd(_BV(LCD_ON_CTRL) | _BV(LCD_ON_DISPLAY));
/* Move cursor home. */
LcdCursorHome();
/* Set data address to zero. */
LcdWriteCmd(_BV(LCD_DDRAM));
return 0;
}
void LcdInit() {
ClockMilliSecondsDelay(16); // >15 ms
lcdIwr=0x38 ;
ClockMilliSecondsDelay(5); // >4.1 ms
lcdIwr=0x38;
ClockMicroSecondsDelay(101); // >100 us
lcdIwr=0x38;
ClockMicroSecondsDelay(101); // >100 us
lcdIwr=0x38; // interface 8 bit
ClockMicroSecondsDelay(41); // >40 us
lcdIwr=0x0c; // display on
ClockMicroSecondsDelay(41); // >40 us
LcdClear();
}
void Init_SmartNavi()
{
HardwareSetup();
R_TMR_CreateOneShot(PDL_TMR_UNIT0,PDL_TMR_OUTPUT_OFF,1,tick_flag,4);
R_INTC_CreateExtInterrupt(PDL_INTC_IRQ5,PDL_INTC_LOW ,Pen_flag,1);
// sendtoRTC();
Init_ADS7843();
#ifdef GpsOn
getPos();
#endif
tone(1);
font_index();
font_index1();
LcdInit();
LcdClear();
Gsm_State(); //initialize variable
Init_Sim900();
}
void showMenu(){
if (isPressed()) {
mode=pos_menu+2;
modechanged=true;
if (mode==5) mode=0;
LcdClear();
return;
}
gotoXY(0,0);
sprintf(cha, " Menu glowne ");LcdString(cha, true);
gotoXY(0,1);
sprintf(cha, " "); LcdString(cha, false);
gotoXY(20,1);
sprintf(cha, "budzik"); LcdString(cha, (pos_menu==0));
gotoXY(0,2);
sprintf(cha, "ust."); LcdString(cha, (pos_menu==1));
gotoXY(30,2);
sprintf(cha, " ^ "); LcdString(cha, false);
gotoXY(50,2);
sprintf(cha, "ust."); LcdString(cha, (pos_menu==2));
gotoXY(0,3);
sprintf(cha, "czas"); LcdString(cha, (pos_menu==1));
gotoXY(30,3);
sprintf(cha, "< > "); LcdString(cha, false);
gotoXY(50,3);
sprintf(cha, "wysw"); LcdString(cha, (pos_menu==2));
gotoXY(0,4);
sprintf(cha, " v"); LcdString(cha, false);
gotoXY(0,5);
sprintf(cha, " "); LcdString(cha, false);
gotoXY(20,5);
sprintf(cha, "powrot"); LcdString(cha, (pos_menu==3));
if (isUp()) pos_menu=0;
if (isDown()) pos_menu=3;
if (isRight()) pos_menu=2;
if (isLeft()) pos_menu=1;
}
/*
* Name : LcdInit
* Description : Performs MCU SPI & LCD controller initialization.
* Argument(s) : None.
* Return value : None.
*/
void LcdInit ( void )
{
/* Pull-up on reset pin. */
LCD_PORT |= _BV ( LCD_RST_PIN );
/* Set output bits on LCD Port. */
LCD_DDR |= _BV( LCD_RST_PIN ) | _BV( LCD_DC_PIN ) | _BV( LCD_CE_PIN ) | _BV( SPI_MOSI_PIN ) | _BV( SPI_CLK_PIN );
Delay();
/* Toggle display reset pin. */
LCD_PORT &= ~( _BV( LCD_RST_PIN ) );
Delay();
LCD_PORT |= _BV ( LCD_RST_PIN );
/* Enable SPI port:
* No interrupt, MSBit first, Master mode, CPOL->0, CPHA->0, Clk/4
*/
SPCR = 0x50;
/* Disable LCD controller */
LCD_PORT |= _BV( LCD_CE_PIN );
LcdSend( 0x21, LCD_CMD ); /* LCD Extended Commands. */
LcdSend( 0xC8, LCD_CMD ); /* Set LCD Vop (Contrast).*/
LcdSend( 0x06, LCD_CMD ); /* Set Temp coefficent. */
LcdSend( 0x13, LCD_CMD ); /* LCD bias mode 1:48. */
LcdSend( 0x20, LCD_CMD ); /* LCD Standard Commands,Horizontal addressing mode */
LcdSend( 0x0C, LCD_CMD ); /* LCD in normal mode. */
/* Reset watermark pointers to empty */
LoWaterMark = LCD_CACHE_SIZE;
HiWaterMark = 0;
/* Clear display on first time use */
LcdClear();
LcdUpdate();
}
u32 PageCurveSet(u8 event)
{
static u8 DrawMask;
static u8 iStk;
static u8 iFocus,Total,iStart;
if(event==PV_INIT)
{
LcdClear(0);
iStk=0;
iFocus=CURVE_NUM;
iStart=0;
Total=CURVE_NUM+CURVE_FUNC;
DrawMask=PD_ALL;
return 1;
}
if(event==PV_USER)
{
LcdClear(0);
DrawMask=PD_ALL;
}
//开始绘图
if(DrawMask)
{
LcdDrawStart(0, 0,LCD_W-1, LCD_H-1, DRAW_NWSE);
//标题绘制
if(DrawMask&PD_TITLE)
{
LcdDrawRect(0, 0,127,13,0);
LcdDrawText(2,0,(char*)PageCurveTitle[iStk]);
if(PageCurveCnt>1) LcdDrawText(96,0,"\1ENT\x2");
LcdDrawHLine(0,LCD_CV_X-2,14,1);
LcdDrawHLine(0,LCD_CV_X-2,15,1);
}
//曲线点列表
if(DrawMask&(PD_LIST|PD_VALUE))
{
u16 i,x,y,idx;
for(i=0,y=18;i<LCD_CURVE_LINES ;i++,y+=7)
{
idx=iStart+i;
LcdBw=(idx==iFocus);
LcdDrawRect(LCD_CV_IX,y,LCD_CV_IX+31,y+7,LcdBw); //绘制选中框
LcdDrawMiniInt(LCD_CV_IX+3,y+1,idx+1,1,0,0xff,0); //绘制曲线序号
LcdDrawMiniNum(LCD_CV_IX+7,y+1,LCD_MN_COL); //绘制分隔点
LcdDrawMiniInt(LCD_CV_IX+30,y+1,PageCurveValue[iStk*CURVE_DS+idx],0,1,0,1); //绘制曲线值
LcdBw=0;
}
//绘制EXP EPA菜单
LcdBw=(iFocus==CURVE_NUM);
LcdDrawRect(3,20,LCD_CV_IX-4,26,LcdBw);
LcdDrawMiniEng(5,21,"EPA\x12");
LcdDrawMiniInt(40,21,PageCurveValue[iStk*CURVE_DS+CURVE_NUM],0,0,1,1); //绘制EPA
LcdBw=(iFocus==CURVE_NUM+1);
LcdDrawRect(3,30,LCD_CV_IX-4,36,LcdBw);
LcdDrawMiniEng(5,31,"EXP\x12");
LcdDrawMiniInt(40,31,PageCurveValue[iStk*CURVE_DS+CURVE_NUM+1],0,0,1,1);//绘制EXP
LcdBw=(iFocus==CURVE_NUM+2);
LcdDrawRect(3,40,LCD_CV_IX-4,46,LcdBw);
LcdDrawMiniEng(5,41,"LEVEL");
LcdBw=(iFocus==CURVE_NUM+3);
LcdDrawRect(3,50,LCD_CV_IX-4,56,LcdBw);
LcdDrawMiniEng(5,51,"RESET");
LcdBw=0;
//绘制曲线
LcdDrawRect(LCD_CV_X,LCD_CV_Y,LCD_CV_X+LCD_CV_W,LCD_CV_Y+LCD_CV_H,1);
LcdDrawRect(LCD_CV_X+1,LCD_CV_Y+1,LCD_CV_X+LCD_CV_W-1,LCD_CV_Y+LCD_CV_H-1,0);
LcdDrawHLine(LCD_CV_X,LCD_CV_X+LCD_CV_W,LCD_CV_Y+LCD_CV_H/2,1);
LcdDrawVLine(LCD_CV_X+LCD_CV_W/2,LCD_CV_Y,LCD_CV_Y+LCD_CV_H,1);
u16 x0,y0;
for(i=0,x0=y0=0;i<CURVE_NUM;i++)
{
x=i*LCD_CV_W/(CURVE_NUM-1);
y=LCD_CV_H-(s32)PageCurveValue[iStk*CURVE_DS+i]*LCD_CV_H/CURVE_TRV;
if(y>LCD_CV_H) y=LCD_CV_H;
LcdDrawLine(LCD_CV_X+x0,LCD_CV_Y+y0,LCD_CV_X+x,LCD_CV_Y+y,1);
if(i==iFocus) LcdDrawVLine(LCD_CV_X+x,LCD_CV_Y,LCD_CV_Y+LCD_CV_H,1);
x0=x;
y0=y;
}
}
//完成绘图
LcdDrawStop();
DrawMask=0;
}
//加减按键处理
s16 v=PageCurveValue[iStk*CURVE_DS+iFocus];
///////////////////////////////////////////////////////////////
if(iFocus<CURVE_NUM)//曲线值
{
if(KeyTstHold(KEY_R))
{
v=(v/10+1)*10;
if(v>CURVE_TRV) v=CURVE_TRV;
DrawMask=PD_LIST;
}
else if(KeyTstDown(KEY_R))
{
if(v<CURVE_TRV) v++;
DrawMask=PD_LIST;
}
if(KeyTstHold(KEY_L))
{
v=(v/10-1)*10;
if(v<0) v=0;
DrawMask=PD_LIST;
}
else if(KeyTstDown(KEY_L))
{
if(v>0) v--;
DrawMask=PD_LIST;
}
}
///////////////////////////////////////////////////////////////
else//EXP EPA等
{
////////////////////////////////////////
if(iFocus==CURVE_NUM+3)//RESET
{
if(KeyTstDown(KEY_R) || KeyTstDown(KEY_L))
{
u32 i;
for(i=0;i<CURVE_NUM;i++) PageCurveValue[iStk*CURVE_DS+i]=i*125;
PageCurveValue[iStk*CURVE_DS+CURVE_NUM ]=100; //epa
PageCurveValue[iStk*CURVE_DS+CURVE_NUM+1]=0; //exp
PageAlert("曲线参数已复位!",500,PV_USER);
}
}
////////////////////////////////////////
if(iFocus==CURVE_NUM+2)//LEVEL
{
s16 delta=0;
if(KeyTstHold(KEY_R)) delta=10;
else if(KeyTstDown(KEY_R)) delta=1;
if(KeyTstHold(KEY_L)) delta=-10;
else if(KeyTstDown(KEY_L)) delta=-1;
if(delta)
{
for(u32 i=0;i<CURVE_NUM;i++)
{
s16 v=PageCurveValue[iStk*CURVE_DS+i];
v+=delta;
if(v>1000) v=1000;
if(v<0) v=0;
PageCurveValue[iStk*CURVE_DS+i]=v;
}
DrawMask=PD_LIST;
}
}
////////////////////////////////////////
if(iFocus==CURVE_NUM+1)//EXP
{
if(KeyTstDown(KEY_R)) if(v<50) v++;
if(KeyTstDown(KEY_L)) if(v>0) v--;
if(PageCurveValue[iStk*CURVE_DS+CURVE_NUM+1]!=v)
{
CurveMake(&PageCurveValue[iStk*CURVE_DS],PageCurveValue[iStk*CURVE_DS+CURVE_NUM],v);
DrawMask=PD_LIST;
}
}
////////////////////////////////////////
if(iFocus==CURVE_NUM)//EPA
{
if(KeyTstDown(KEY_R)) if(v<100) v++;
if(KeyTstDown(KEY_L)) if(v>-100) v--;
if(PageCurveValue[iStk*CURVE_DS+CURVE_NUM]!=v)
{
CurveMake(&PageCurveValue[iStk*CURVE_DS],v,PageCurveValue[iStk*CURVE_DS+CURVE_NUM+1]);
DrawMask=PD_LIST;
}
}
}
PageCurveValue[iStk*CURVE_DS+iFocus]=v;
///////////////////////////////////////////////////////////////
//上下按键处理
if(KeyTstDown(KEY_UP))
{
if(iFocus>0) iFocus--;
else iFocus=Total-1;
DrawMask=PD_LIST|PD_IDX;
}
if(KeyTstDown(KEY_DW))
{
if(iFocus<Total-1) iFocus++;
else iFocus=0;
DrawMask=PD_LIST|PD_IDX;
}
if(iFocus>=Total) iFocus=Total-1;
if(iFocus>=CURVE_NUM) iStart=0;
else if(iFocus<iStart) iStart=iFocus;
else if(iFocus>iStart+LCD_CURVE_LINES-1) iStart=iFocus-LCD_CURVE_LINES+1;
///////////////////////////////////////////////////////////////
//回车键切换曲线
if(KeyTstDown(KEY_ENT) )
{
iStk++;
if(iStk>=PageCurveCnt) iStk=0;
DrawMask|=PD_ALL;
}
///////////////////////////////////////////////////////////////
//返回键处理
if(KeyTstDown(KEY_EXT) )
{
PageReturn(PV_REDRAW);
}
KeyClearDown(KEY_MENUALL);
return 0;
}