void Task_Moto(void *Tags)
{
uint16 Door=1700;
while(1)
{
uint16 i =0;
MOTOR_EN(0);
if(AngleXY[0]<(Door-10))MOTOR_DIR(MOVE_UP);
else if(AngleXY[0]>(Door+10))MOTOR_DIR(MOVE_DN);
else MOTOR_EN(1);
for(i=0; i < 2 ; i++)
{
MOTOR_PLUSE(0);
Tos_TaskDelay(PULSE_DELAY);
MOTOR_PLUSE(1);
Tos_TaskDelay(PULSE_DELAY);
}
}
}
int main(void)
{
init(); //! Call init
uint8_t Go_A=0; //! Drive Command memory for direction A
uint8_t Go_B=0;
uint8_t key; //! Char code from keyboard, currently used for remote ctrl
while(1)
{
UPRINT("\f"); //! Terminal form feeds
// error_median_check(); //! Call Median check
error_limits_check(); //! Call Limit check
error_nfault_check(); //! Call nFault check
if (error_reg != 0) error_modul (); //! Fault detection
//! Call "error_modul" if an error occurs
if(GET_REMOTE_SWITCH) //! If the remote switch is set (PA4) the move direction can be remote controlled by pressing a or b...
{ //! ... on the keyboard of the PC which is connected through the UART with the motor control board
UPRINT("Modus: Remote\r\n");
key = uart_getc_nowait(); //! defining "key" with a key-input through the uart
UPRINT("Key: "); //! print out a probably pressed key on the remote console
UPRINTN(key);
UPRINT("\r\n");
if(key == 'a') //! If key "a" was pressed during remote mode, set Go_a=1 and Go_B=0
{
Go_A = 1;
Go_B = 0;
}
else if(key == 'b') //! If key "b" was pressed during remote mode, set Go_a=0 and Go_B=1
{
Go_A = 0;
Go_B = 1;
}
if(GET_BUTTON_A_RMT && GET_BUTTON_B_RMT) {Go_A = 0; Go_B = 0;} //! if both direction buttons are pressed simultaneously, Go_A and GO_B are 0, the motor stands still
if(GET_BUTTON_A_RMT) {Go_A = 1; Go_B = 0;} //! if switch A is pressed, set Go_a=1 and Go_B=0 for driving the motor to A
if(GET_BUTTON_B_RMT) {Go_A = 0; Go_B = 1;}
}
else //! If the remote mode is deactivated, the direction buttons must be pressed direct at the front panel
{
UPRINT("Modus: Local\r\n\r\n");
if(GET_BUTTON_A && GET_BUTTON_B) {Go_A = 0; Go_B = 0;} //! if both direction buttons are pressed simultaneously, Go_A and GO_B are 0, the motor stands still
if(GET_BUTTON_A) {Go_A = 1; Go_B = 0;} //! if switch A is pressed, set Go_a=1 and Go_B=0 for driving the motor to A
if(GET_BUTTON_B) {Go_A = 0; Go_B = 1;} //! if switch B is pressed, set Go_a=0 and Go_B=1 for driving the motor to B
}
UPRINTN(lastLimit); //! give out the last pressed limit switch to the remote console
UPRINT(" Lastlimit\r\n");
if(GET_LIMIT_A) TURN_ON(PORT_LMT_A_LED, LMT_A_LED); //! check if limit switch A is pressed and show it by LED on the front panel
else TURN_OFF(PORT_LMT_A_LED, LMT_A_LED); //! if limit switch A is not pressed, light off the limit LED for limit switch A
if(GET_LIMIT_B) TURN_ON(PORT_LMT_B_LED, LMT_B_LED); //! check if limit switch B is pressed and show it by LED on the front panel
else TURN_OFF(PORT_LMT_B_LED, LMT_B_LED); //! if limit switch B is not pressed, light off the limit LED for limit switch B
// if(GET_MOTOR_STOP) //! if the motor stop button is pressed...
// {
// Go_A = 0; Go_B = 0; //! ... set Go_A=0 and Go_B=0, ...
// Motor_stop(); //! ... call the "motorstop()" routine...
// TURN_OFF(PORT_DIR_A_LED , DIR_A_LED ); //! ... and light off both direction LED's
// TURN_OFF(PORT_DIR_B_LED , DIR_B_LED );
// }
// else //! if the motor stop button is not press, than check different status of the A/B buttons and limit switches
// {
if (GET_LIMIT_A && !(GET_LIMIT_B)) //! Limit switch A is pressed, Limit switch B is not pressed //Endschalter A gedrueckt, Endschalter B nicht gedreuckt
{
DBPRINT("LA=1 LB=0\r\n"); //! print out to the remote console which limit switch is pressed
if (Go_B) //! if button B is pressed...
{
Motor_RE(); //! ... call "Motor_RE" routine for driving the motor to B
TURN_ON(PORT_DIR_B_LED , DIR_B_LED ); //! turn on the LED for driving to B
TURN_OFF(PORT_DIR_A_LED , DIR_A_LED ); //! turn off the LED for driving A, if the motor was driving to A but not reached it before the driving direction was switched
UPRINT("Fahre Richtung B\r\n"); //! print out the driving direction int the remote console
}
if (Go_A) //! if button A is pressed, call "Motor_stop", because the motor can't drive to A, if the limit switch A is pressed
{
Go_A = 0;
Motor_stop(); //! Call Motor stop
TURN_OFF(PORT_DIR_A_LED , DIR_A_LED ); //! light off both direction LED's
TURN_OFF(PORT_DIR_B_LED , DIR_B_LED );
UPRINT("\r\n Stop bei A\r\n"); //! print out to the remote console that he motor stops/stand still
}
}
if (GET_LIMIT_B && !(GET_LIMIT_A)) //! Limit switch B is pressed, Limit switch A is not pressed //Endschalter A gedrueckt, Endschalter B nicht gedreuckt
{
DBPRINT("LA=0 LB=1\r\n"); //! print out to the remote console which limit switch is pressed
if (Go_A) //! if button A is pressed...
{
Motor_FW(); //! ... call "Motor_FW" routine for driving the motor to B
TURN_ON(PORT_DIR_A_LED , DIR_A_LED ); //! turn on the LED for driving to A
TURN_OFF(PORT_DIR_B_LED , DIR_B_LED ); //! turn off the LED for driving B, if the motor was driving to A but not reached it before the driving direction was switched
UPRINT("Fahre Richtung A\r\n"); //! print out the driving direction int the remote console
}
if (Go_B) //! if button B is pressed, call "Motor_stop", because the motor can't drive to A, if the limit switch A is pressed
{
Go_B = 0;
Motor_stop();
TURN_OFF(PORT_DIR_A_LED , DIR_A_LED ); //! light off both direction LED's
TURN_OFF(PORT_DIR_B_LED , DIR_B_LED );
UPRINT("\r\n Stop bei B\r\n"); //! print out to the remote console that he motor stops/stand still
}
}
if (!(GET_LIMIT_A) && !(GET_LIMIT_B)) //! none of the limit switches is pressed
{
DBPRINT("LA=0 LB=0\r\n");
if (Go_A) //! if button A is pressed ...
{
Go_B = 0;
Motor_FW(); //! call motor forward function
TURN_ON(PORT_DIR_A_LED , DIR_A_LED ); //! turn on direction LED A
TURN_OFF(PORT_DIR_B_LED , DIR_B_LED ); //! turn off direction LED B
UPRINT("Fahre Richtung A\r\n");
}
else if (Go_B) //! if button B is pressed...
{
Motor_RE(); //! call motor reverse function
TURN_ON(PORT_DIR_B_LED , DIR_B_LED ); //! turn on direction LED B
TURN_OFF(PORT_DIR_A_LED , DIR_A_LED ); //! turn off direction LED A
UPRINT("Fahre Richtung B\r\n");
}
}
//}
/*
medIDrv = median(&pRbIDrv->mem[0]); //! sample median for driver current
medU24 = median(&pRbU24->mem[0]); //! sample median for supply voltage
medUFuse = median(&pRbUFuse->mem[0]); //! sample median for fuse voltage
*/
medIDrv = dbg_medIDrv;
medU24 = dbg_medU24;
medUFuse = dbg_medUFuse;
DBPRINT("\r\n\r\nMedian output:\r\n"); //! print out the different median values
DBPRINTN(medIDrv);
DBPRINT("\t mA medIDrv \r\n");
DBPRINTN(medU24);
DBPRINT("\t mV medU24 \r\n");
DBPRINTN(medUFuse);
DBPRINT("\t mV medUFuse \r\n");
DBPRINT("\r\n\r\nMotor:\r\n");
DBPRINT("Typ\tStatus\tMotorDirection\tSLEEP\tENABLE\tPHASE\tMODE\r\n");
MOTOR_TYPE();
DBPRINT("\t");
if ( (PORT_DRV & ~DRV_EN) && (PORT_DRV & DRV_MODE) ) DBPRINT("BRAKE"); //! set Motor BRAKE
else if (!(PORT_DRV & DRV_SLEEP)) DBPRINT("SLEEP"); //! set Motor SLEEP
else if ((PORT_DRV & DRV_SLEEP)) DBPRINT("ARMED"); //! set Motor ARMED
else DBPRINT("Unknown"); // ?
DBPRINT("\t");
MOTOR_DIR();
DBPRINT("\t");
if (PORT_DRV & DRV_SLEEP) DBPRINT ("1"); //! if driver_sleep bit is set, set motor sleep 1 // motor sleep
else DBPRINT ("0");
DBPRINT("\t");
if (PORT_DRV & DRV_EN) DBPRINT("1"); //! if driver_enabled bir is set, set motor enable 1 // motor enable
else DBPRINT("0");
DBPRINT("\t");
if (PORT_DRV & DRV_PHASE) DBPRINT("1"); //! if driver_phase is set, set motor phase 1 // motor phase
else DBPRINT("0");
DBPRINT("\t");
if (PORT_DRV & DRV_MODE) DBPRINT("1"); //! if driver_mode is set, set motor mode 1 // motor mode
else DBPRINT("0");
DBPRINT("\r\n");
wdt_reset();
_delay_ms(100);
}
}
