void gpio_config(GPIO_ConfigTypeDef *pGPIOConfig)
{
uint32 gpio_pin_mask = pGPIOConfig->GPIO_Pin;
uint32 gpio_pin_mask_high = pGPIOConfig->GPIO_Pin_high;
uint32 io_reg;
uint8 io_num = 0;
uint32 pin_reg;
uint32 bit_valid;
if (pGPIOConfig->GPIO_Mode == GPIO_Mode_Input) {
GPIO_AS_INPUT(gpio_pin_mask);
GPIO_AS_INPUT_HIGH(gpio_pin_mask_high);
} else if (pGPIOConfig->GPIO_Mode == GPIO_Mode_Output) {
GPIO_AS_OUTPUT(gpio_pin_mask);
GPIO_AS_OUTPUT_HIGH(gpio_pin_mask_high);
}
do {
bit_valid = (io_num >= 32 ? (gpio_pin_mask_high & (0x1 << (io_num - 32))) : (gpio_pin_mask & (0x1 << io_num)));
if (bit_valid && (io_reg = GPIO_PIN_REG[io_num])) {
if (pGPIOConfig->GPIO_Mode == GPIO_Mode_Input) {
SET_PERI_REG_MASK(io_reg, FUN_IE);
}
//for ESP32 function 2 of every pad is allways GPIO func
PIN_FUNC_SELECT(io_reg, 2);
if (pGPIOConfig->GPIO_Pullup) {
PIN_PULLUP_EN(io_reg);
} else {
PIN_PULLUP_DIS(io_reg);
}
if (pGPIOConfig->GPIO_Pulldown) {
PIN_PULLDWN_EN(io_reg);
} else {
PIN_PULLDWN_DIS(io_reg);
}
if (pGPIOConfig->GPIO_Mode == GPIO_Mode_Out_OD) {
portENTER_CRITICAL();
pin_reg = GPIO_REG_READ(GPIO_PIN_ADDR(io_num));
//pin_reg &= (~GPIO_GPIO_PIN0_PAD_DRIVER);
pin_reg |= GPIO_GPIO_PIN0_PAD_DRIVER;
GPIO_REG_WRITE(GPIO_PIN_ADDR(io_num), pin_reg);
portEXIT_CRITICAL();
}
gpio_pin_intr_state_set(io_num, pGPIOConfig->GPIO_IntrType);
}
io_num++;
} while (io_num < GPIO_PIN_COUNT);
}
/**
* Sets the pull up and pull down registers for a pin.
*/
static void ICACHE_FLASH_ATTR
easygpio_setupPulls(uint32_t gpio_name, bool pullUp, bool pullDown) {
if (pullUp) {
PIN_PULLDWN_DIS(gpio_name);
PIN_PULLUP_EN(gpio_name);
} else if (pullDown) {
PIN_PULLUP_DIS(gpio_name);
PIN_PULLDWN_EN(gpio_name);
} else {
PIN_PULLDWN_DIS(gpio_name);
PIN_PULLUP_DIS(gpio_name);
}
}
/**
* Sets the pull up and pull down registers for a pin.
* This seems to do very little for the actual pull effect
* - it's always pull up for both EASYGPIO_PULLUP and EASYGPIO_PULLDOWN.
* But that is something the SDK needs to fix.
*/
static void ICACHE_FLASH_ATTR
easygpio_setupPullsByName(uint32_t gpio_name, EasyGPIO_PullStatus pullStatus) {
if (EASYGPIO_PULLUP == pullStatus){
PIN_PULLDWN_DIS(gpio_name);
PIN_PULLUP_EN(gpio_name);
} else if (EASYGPIO_PULLDOWN == pullStatus){
PIN_PULLUP_DIS(gpio_name);
PIN_PULLDWN_EN(gpio_name);
} else {
PIN_PULLDWN_DIS(gpio_name);
PIN_PULLUP_DIS(gpio_name);
}
}
int platform_gpio_mode( unsigned pin, unsigned mode, unsigned pull )
{
// NODE_DBG("Function platform_gpio_mode() is called. pin_mux:%d, func:%d\n",pin_mux[pin],pin_func[pin]);
if (pin >= NUM_GPIO)
return -1;
if(pin == 0){
if(mode==PLATFORM_GPIO_INPUT)
gpio16_input_conf();
else
gpio16_output_conf();
return 1;
}
platform_pwm_close(pin); // closed from pwm module, if it is used in pwm
switch(pull){
case PLATFORM_GPIO_PULLUP:
PIN_PULLDWN_DIS(pin_mux[pin]);
PIN_PULLUP_EN(pin_mux[pin]);
break;
case PLATFORM_GPIO_PULLDOWN:
PIN_PULLUP_DIS(pin_mux[pin]);
PIN_PULLDWN_EN(pin_mux[pin]);
break;
case PLATFORM_GPIO_FLOAT:
PIN_PULLUP_DIS(pin_mux[pin]);
PIN_PULLDWN_DIS(pin_mux[pin]);
break;
default:
PIN_PULLUP_DIS(pin_mux[pin]);
PIN_PULLDWN_DIS(pin_mux[pin]);
break;
}
switch(mode){
case PLATFORM_GPIO_INPUT:
#if defined( LUA_USE_MODULES_GPIO ) && defined( GPIO_INTERRUPT_ENABLE )
lua_gpio_unref(pin); // unref the lua ref call back.
#endif
GPIO_DIS_OUTPUT(pin_num[pin]);
case PLATFORM_GPIO_OUTPUT:
ETS_GPIO_INTR_DISABLE();
#ifdef GPIO_INTERRUPT_ENABLE
pin_int_type[pin] = GPIO_PIN_INTR_DISABLE;
#endif
PIN_FUNC_SELECT(pin_mux[pin], pin_func[pin]);
//disable interrupt
gpio_pin_intr_state_set(GPIO_ID_PIN(pin_num[pin]), GPIO_PIN_INTR_DISABLE);
//clear interrupt status
GPIO_REG_WRITE(GPIO_STATUS_W1TC_ADDRESS, BIT(pin_num[pin]));
GPIO_REG_WRITE(GPIO_PIN_ADDR(GPIO_ID_PIN(pin_num[pin])), GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(pin_num[pin]))) & (~ GPIO_PIN_PAD_DRIVER_SET(GPIO_PAD_DRIVER_ENABLE))); //disable open drain;
ETS_GPIO_INTR_ENABLE();
break;
#ifdef GPIO_INTERRUPT_ENABLE
case PLATFORM_GPIO_INT:
ETS_GPIO_INTR_DISABLE();
PIN_FUNC_SELECT(pin_mux[pin], pin_func[pin]);
GPIO_DIS_OUTPUT(pin_num[pin]);
gpio_register_set(GPIO_PIN_ADDR(GPIO_ID_PIN(pin_num[pin])), GPIO_PIN_INT_TYPE_SET(GPIO_PIN_INTR_DISABLE)
| GPIO_PIN_PAD_DRIVER_SET(GPIO_PAD_DRIVER_DISABLE)
| GPIO_PIN_SOURCE_SET(GPIO_AS_PIN_SOURCE));
ETS_GPIO_INTR_ENABLE();
break;
#endif
default:
break;
}
return 1;
}
