static void jz_board_do_resume(unsigned long *ptr)
{
unsigned char i;
/* Restore GPIO registers */
for(i = 1; i < GPIO_PORT_NUM; i++) {
REG_GPIO_PXFUNS(i) = *ptr;
REG_GPIO_PXFUNC(i) = ~(*ptr++);
REG_GPIO_PXSELS(i) = *ptr;
REG_GPIO_PXSELC(i) = ~(*ptr++);
REG_GPIO_PXDIRS(i) = *ptr;
REG_GPIO_PXDIRC(i) = ~(*ptr++);
REG_GPIO_PXPES(i) = *ptr;
REG_GPIO_PXPEC(i) = ~(*ptr++);
REG_GPIO_PXIMS(i)=*ptr;
REG_GPIO_PXIMC(i)=~(*ptr++);
REG_GPIO_PXDATS(i)=*ptr;
REG_GPIO_PXDATC(i)=~(*ptr++);
REG_GPIO_PXTRGS(i)=*ptr;
REG_GPIO_PXTRGC(i)=~(*ptr++);
}
/* Print messages of GPIO registers for debug */
for(i=0;i<GPIO_PORT_NUM;i++) {
dprintk("resume dat:%x pin:%x fun:%x sel:%x dir:%x pull:%x msk:%x trg:%x\n", \
REG_GPIO_PXDAT(i),REG_GPIO_PXPIN(i),REG_GPIO_PXFUN(i),REG_GPIO_PXSEL(i), \
REG_GPIO_PXDIR(i),REG_GPIO_PXPE(i),REG_GPIO_PXIM(i),REG_GPIO_PXTRG(i));
}
}
void board_save_gpio(unsigned int *ptr){
int i = 0;
for(i = 0; i < GPIO_PORT_NUM; i++) {
*ptr++ = REG_GPIO_PXFUN(i);
*ptr++ = REG_GPIO_PXSEL(i);
*ptr++ = REG_GPIO_PXDIR(i);
*ptr++ = REG_GPIO_PXPE(i);
*ptr++ = REG_GPIO_PXIM(i);
*ptr++ = REG_GPIO_PXDAT(i);
*ptr++ = REG_GPIO_PXTRG(i);
}
return;
}
/* NOTES:
* 1: Pins that are floated (NC) should be set as input and pull-enable.
* 2: Pins that are pull-up or pull-down by outside should be set as input
* and pull-disable.
* 3: Pins that are connected to a chip except sdram and nand flash
* should be set as input and pull-disable, too.
*/
static void jz_board_do_sleep(unsigned long *ptr)
{
unsigned char i;
/* Print messages of GPIO registers for debug */
for(i=0;i<GPIO_PORT_NUM;i++) {
dprintk("run dat:%x pin:%x fun:%x sel:%x dir:%x pull:%x msk:%x trg:%x\n", \
REG_GPIO_PXDAT(i),REG_GPIO_PXPIN(i),REG_GPIO_PXFUN(i),REG_GPIO_PXSEL(i), \
REG_GPIO_PXDIR(i),REG_GPIO_PXPE(i),REG_GPIO_PXIM(i),REG_GPIO_PXTRG(i));
}
/* Save GPIO registers */
for(i = 1; i < GPIO_PORT_NUM; i++) {
*ptr++ = REG_GPIO_PXFUN(i);
*ptr++ = REG_GPIO_PXSEL(i);
*ptr++ = REG_GPIO_PXDIR(i);
*ptr++ = REG_GPIO_PXPE(i);
*ptr++ = REG_GPIO_PXIM(i);
*ptr++ = REG_GPIO_PXDAT(i);
*ptr++ = REG_GPIO_PXTRG(i);
}
/*
* Set all pins to pull-disable, and set all pins as input except
* sdram and the pins which can be used as CS1_N to CS4_N for chip select.
*/
__gpio_as_sleep();
/*
* Set proper status for GPC21 to GPC24 which can be used as CS1_N to CS4_N.
* Keep the pins' function used for chip select(CS) here according to your
* system to avoid chip select crashing with sdram when resuming from sleep mode.
*/
#if defined(CONFIG_JZ4750L_APUS)
/* GPB25/CS1_N is used as chip select for nand flash, shouldn't be change. */
/* GPB26/CS2_N is connected to nand flash, needn't be changed. */
/* GPB28/CS3_N is used as cs8900's chip select, shouldn't be changed. */
/* GPB27/CS4_N is used as NOR's chip select, shouldn't be changed. */
#endif
/*
* Enable pull for NC pins here according to your system
*/
#if defined(CONFIG_JZ4750L_APUS)
#endif
/*
* If you must set some GPIOs as output to high level or low level,
* you can set them here, using:
* __gpio_as_output(n);
* __gpio_set_pin(n); or __gpio_clear_pin(n);
*/
#if defined(CONFIG_JZ4750L_APUS)
/* GPC7 which is used as AMPEN_N should be set to high to disable audio amplifier */
__gpio_as_output(32*2+7);
__gpio_set_pin(32*2+7);
#endif
#ifdef DEBUG
/* Keep uart function for printing debug message */
__gpio_as_uart0();
__gpio_as_uart1();
__gpio_as_uart2();
__gpio_as_uart3();
/* Print messages of GPIO registers for debug */
for(i=0;i<GPIO_PORT_NUM;i++) {
dprintk("sleep dat:%x pin:%x fun:%x sel:%x dir:%x pull:%x msk:%x trg:%x\n", \
REG_GPIO_PXDAT(i),REG_GPIO_PXPIN(i),REG_GPIO_PXFUN(i),REG_GPIO_PXSEL(i), \
REG_GPIO_PXDIR(i),REG_GPIO_PXPE(i),REG_GPIO_PXIM(i),REG_GPIO_PXTRG(i));
}
#endif
}