static void ar9003_hw_spur_ofdm(struct ath_hw *ah,
int freq_offset,
int spur_freq_sd,
int spur_delta_phase,
int spur_subchannel_sd)
{
int mask_index = 0;
/* OFDM Spur mitigation */
REG_RMW_FIELD(ah, AR_PHY_TIMING4,
AR_PHY_TIMING4_ENABLE_SPUR_FILTER, 0x1);
REG_RMW_FIELD(ah, AR_PHY_TIMING11,
AR_PHY_TIMING11_SPUR_FREQ_SD, spur_freq_sd);
REG_RMW_FIELD(ah, AR_PHY_TIMING11,
AR_PHY_TIMING11_SPUR_DELTA_PHASE, spur_delta_phase);
REG_RMW_FIELD(ah, AR_PHY_SFCORR_EXT,
AR_PHY_SFCORR_EXT_SPUR_SUBCHANNEL_SD, spur_subchannel_sd);
REG_RMW_FIELD(ah, AR_PHY_TIMING11,
AR_PHY_TIMING11_USE_SPUR_FILTER_IN_AGC, 0x1);
REG_RMW_FIELD(ah, AR_PHY_TIMING11,
AR_PHY_TIMING11_USE_SPUR_FILTER_IN_SELFCOR, 0x1);
REG_RMW_FIELD(ah, AR_PHY_TIMING4,
AR_PHY_TIMING4_ENABLE_SPUR_RSSI, 0x1);
REG_RMW_FIELD(ah, AR_PHY_SPUR_REG,
AR_PHY_SPUR_REG_SPUR_RSSI_THRESH, 34);
REG_RMW_FIELD(ah, AR_PHY_SPUR_REG,
AR_PHY_SPUR_REG_EN_VIT_SPUR_RSSI, 1);
if (REG_READ_FIELD(ah, AR_PHY_MODE,
AR_PHY_MODE_DYNAMIC) == 0x1)
REG_RMW_FIELD(ah, AR_PHY_SPUR_REG,
AR_PHY_SPUR_REG_ENABLE_NF_RSSI_SPUR_MIT, 1);
mask_index = (freq_offset << 4) / 5;
if (mask_index < 0)
mask_index = mask_index - 1;
mask_index = mask_index & 0x7f;
REG_RMW_FIELD(ah, AR_PHY_SPUR_REG,
AR_PHY_SPUR_REG_ENABLE_MASK_PPM, 0x1);
REG_RMW_FIELD(ah, AR_PHY_TIMING4,
AR_PHY_TIMING4_ENABLE_PILOT_MASK, 0x1);
REG_RMW_FIELD(ah, AR_PHY_TIMING4,
AR_PHY_TIMING4_ENABLE_CHAN_MASK, 0x1);
REG_RMW_FIELD(ah, AR_PHY_PILOT_SPUR_MASK,
AR_PHY_PILOT_SPUR_MASK_CF_PILOT_MASK_IDX_A, mask_index);
REG_RMW_FIELD(ah, AR_PHY_SPUR_MASK_A,
AR_PHY_SPUR_MASK_A_CF_PUNC_MASK_IDX_A, mask_index);
REG_RMW_FIELD(ah, AR_PHY_CHAN_SPUR_MASK,
AR_PHY_CHAN_SPUR_MASK_CF_CHAN_MASK_IDX_A, mask_index);
REG_RMW_FIELD(ah, AR_PHY_PILOT_SPUR_MASK,
AR_PHY_PILOT_SPUR_MASK_CF_PILOT_MASK_A, 0xc);
REG_RMW_FIELD(ah, AR_PHY_CHAN_SPUR_MASK,
AR_PHY_CHAN_SPUR_MASK_CF_CHAN_MASK_A, 0xc);
REG_RMW_FIELD(ah, AR_PHY_SPUR_MASK_A,
AR_PHY_SPUR_MASK_A_CF_PUNC_MASK_A, 0xa0);
REG_RMW_FIELD(ah, AR_PHY_SPUR_REG,
AR_PHY_SPUR_REG_MASK_RATE_CNTL, 0xff);
}
/* reset device */
void dwc_device_reset(dwc_dev_t *dev)
{
/* start reset */
REG_WRITE_FIELD(dev, DCTL, CSFTRST, 1);
/* wait until done */
while(REG_READ_FIELD(dev, DCTL, CSFTRST));
}
static void ar9003_hw_spur_ofdm_work(struct ath_hw *ah,
struct ath9k_channel *chan,
int freq_offset)
{
int spur_freq_sd = 0;
int spur_subchannel_sd = 0;
int spur_delta_phase = 0;
if (IS_CHAN_HT40(chan)) {
if (freq_offset < 0) {
if (REG_READ_FIELD(ah, AR_PHY_GEN_CTRL,
AR_PHY_GC_DYN2040_PRI_CH) == 0x0)
spur_subchannel_sd = 1;
else
spur_subchannel_sd = 0;
spur_freq_sd = ((freq_offset + 10) << 9) / 11;
} else {
if (REG_READ_FIELD(ah, AR_PHY_GEN_CTRL,
AR_PHY_GC_DYN2040_PRI_CH) == 0x0)
spur_subchannel_sd = 0;
else
spur_subchannel_sd = 1;
spur_freq_sd = ((freq_offset - 10) << 9) / 11;
}
spur_delta_phase = (freq_offset << 17) / 5;
} else {
spur_subchannel_sd = 0;
spur_freq_sd = (freq_offset << 9) /11;
spur_delta_phase = (freq_offset << 18) / 5;
}
spur_freq_sd = spur_freq_sd & 0x3ff;
spur_delta_phase = spur_delta_phase & 0xfffff;
ar9003_hw_spur_ofdm(ah,
freq_offset,
spur_freq_sd,
spur_delta_phase,
spur_subchannel_sd);
}
/* generic api to send device command */
static void dwc_device_cmd(dwc_dev_t *dev, dwc_device_cmd_t *cmd)
{
uint8_t active = REG_READ_FIELD(dev, DGCMD, CMDACT);
ASSERT(active);
REG_WRITE(dev, DGCMDPAR, cmd->param);
REG_WRITE_FIELD(dev, DGCMD, CMDTYP, cmd->cmd);
/* wait until active field is cleared. */
while(!REG_READ_FIELD(dev, DGCMD, CMDACT));
if(REG_READ_FIELD(dev, DGCMD, CMDSTATUS))
{
ERR("\n\n device command failed. \n\n");
ASSERT(0);
}
}
/* Spur mitigation for OFDM */
static void ar9003_hw_spur_mitigate_ofdm(struct ath_hw *ah,
struct ath9k_channel *chan)
{
int synth_freq;
int range = 10;
int freq_offset = 0;
int mode;
u8* spurChansPtr;
unsigned int i;
struct ar9300_eeprom *eep = &ah->eeprom.ar9300_eep;
if (IS_CHAN_5GHZ(chan)) {
spurChansPtr = &(eep->modalHeader5G.spurChans[0]);
mode = 0;
}
else {
spurChansPtr = &(eep->modalHeader2G.spurChans[0]);
mode = 1;
}
if (spurChansPtr[0] == 0)
return; /* No spur in the mode */
if (IS_CHAN_HT40(chan)) {
range = 19;
if (REG_READ_FIELD(ah, AR_PHY_GEN_CTRL,
AR_PHY_GC_DYN2040_PRI_CH) == 0x0)
synth_freq = chan->channel - 10;
else
synth_freq = chan->channel + 10;
} else {
range = 10;
synth_freq = chan->channel;
}
ar9003_hw_spur_ofdm_clear(ah);
for (i = 0; spurChansPtr[i] && i < 5; i++) {
freq_offset = FBIN2FREQ(spurChansPtr[i], mode) - synth_freq;
if (abs(freq_offset) < range) {
ar9003_hw_spur_ofdm_work(ah, chan, freq_offset);
break;
}
}
}
static void ar9003_hw_patch_rtt(struct ath_hw *ah, int index, int chain)
{
int agc, caldac;
if (!test_bit(SW_PKDET_DONE, &ah->caldata->cal_flags))
return;
if ((index != 5) || (chain >= 2))
return;
agc = REG_READ_FIELD(ah, AR_PHY_65NM_RXRF_AGC(chain),
AR_PHY_65NM_RXRF_AGC_AGC_OVERRIDE);
if (!agc)
return;
caldac = ah->caldata->caldac[chain];
ah->caldata->rtt_table[chain][index] &= 0xFFFF05FF;
caldac = (caldac & 0x20) | ((caldac & 0x1F) << 7);
ah->caldata->rtt_table[chain][index] |= (caldac << 4);
}
static void ar9003_mci_prep_interface(struct ath_hw *ah)
{
struct ath_common *common = ath9k_hw_common(ah);
struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci;
u32 saved_mci_int_en;
u32 mci_timeout = 150;
mci->bt_state = MCI_BT_SLEEP;
saved_mci_int_en = REG_READ(ah, AR_MCI_INTERRUPT_EN);
REG_WRITE(ah, AR_MCI_INTERRUPT_EN, 0);
REG_WRITE(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
REG_READ(ah, AR_MCI_INTERRUPT_RX_MSG_RAW));
REG_WRITE(ah, AR_MCI_INTERRUPT_RAW,
REG_READ(ah, AR_MCI_INTERRUPT_RAW));
ar9003_mci_remote_reset(ah, true);
ar9003_mci_send_req_wake(ah, true);
if (!ar9003_mci_wait_for_interrupt(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
AR_MCI_INTERRUPT_RX_MSG_SYS_WAKING, 500))
goto clear_redunt;
mci->bt_state = MCI_BT_AWAKE;
/*
* we don't need to send more remote_reset at this moment.
* If BT receive first remote_reset, then BT HW will
* be cleaned up and will be able to receive req_wake
* and BT HW will respond sys_waking.
* In this case, WLAN will receive BT's HW sys_waking.
* Otherwise, if BT SW missed initial remote_reset,
* that remote_reset will still clean up BT MCI RX,
* and the req_wake will wake BT up,
* and BT SW will respond this req_wake with a remote_reset and
* sys_waking. In this case, WLAN will receive BT's SW
* sys_waking. In either case, BT's RX is cleaned up. So we
* don't need to reply BT's remote_reset now, if any.
* Similarly, if in any case, WLAN can receive BT's sys_waking,
* that means WLAN's RX is also fine.
*/
ar9003_mci_send_sys_waking(ah, true);
udelay(10);
/*
* Set BT priority interrupt value to be 0xff to
* avoid having too many BT PRIORITY interrupts.
*/
REG_WRITE(ah, AR_MCI_BT_PRI0, 0xFFFFFFFF);
REG_WRITE(ah, AR_MCI_BT_PRI1, 0xFFFFFFFF);
REG_WRITE(ah, AR_MCI_BT_PRI2, 0xFFFFFFFF);
REG_WRITE(ah, AR_MCI_BT_PRI3, 0xFFFFFFFF);
REG_WRITE(ah, AR_MCI_BT_PRI, 0X000000FF);
/*
* A contention reset will be received after send out
* sys_waking. Also BT priority interrupt bits will be set.
* Clear those bits before the next step.
*/
REG_WRITE(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
AR_MCI_INTERRUPT_RX_MSG_CONT_RST);
REG_WRITE(ah, AR_MCI_INTERRUPT_RAW, AR_MCI_INTERRUPT_BT_PRI);
if (mci->is_2g) {
ar9003_mci_send_lna_transfer(ah, true);
udelay(5);
}
if ((mci->is_2g && !mci->update_2g5g)) {
if (ar9003_mci_wait_for_interrupt(ah,
AR_MCI_INTERRUPT_RX_MSG_RAW,
AR_MCI_INTERRUPT_RX_MSG_LNA_INFO,
mci_timeout))
ath_dbg(common, MCI,
"MCI WLAN has control over the LNA & BT obeys it\n");
else
ath_dbg(common, MCI,
"MCI BT didn't respond to LNA_TRANS\n");
}
clear_redunt:
/* Clear the extra redundant SYS_WAKING from BT */
if ((mci->bt_state == MCI_BT_AWAKE) &&
(REG_READ_FIELD(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
AR_MCI_INTERRUPT_RX_MSG_SYS_WAKING)) &&
(REG_READ_FIELD(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
AR_MCI_INTERRUPT_RX_MSG_SYS_SLEEPING) == 0)) {
REG_WRITE(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
AR_MCI_INTERRUPT_RX_MSG_SYS_WAKING);
REG_WRITE(ah, AR_MCI_INTERRUPT_RAW,
AR_MCI_INTERRUPT_REMOTE_SLEEP_UPDATE);
}
REG_WRITE(ah, AR_MCI_INTERRUPT_EN, saved_mci_int_en);
}
/* read the current connection speed. */
uint8_t dwc_connectspeed(dwc_dev_t *dev)
{
return REG_READ_FIELD(dev, DSTS, CONNECTSPD);
}
/* is device running? */
uint8_t dwc_device_run_status(dwc_dev_t *dev)
{
return REG_READ_FIELD(dev, DCTL, RUN_STOP);
}
static void ar9003_mci_prep_interface(struct ath_hw *ah)
{
struct ath_common *common = ath9k_hw_common(ah);
struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci;
u32 saved_mci_int_en;
u32 mci_timeout = 150;
mci->bt_state = MCI_BT_SLEEP;
saved_mci_int_en = REG_READ(ah, AR_MCI_INTERRUPT_EN);
REG_WRITE(ah, AR_MCI_INTERRUPT_EN, 0);
REG_WRITE(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
REG_READ(ah, AR_MCI_INTERRUPT_RX_MSG_RAW));
REG_WRITE(ah, AR_MCI_INTERRUPT_RAW,
REG_READ(ah, AR_MCI_INTERRUPT_RAW));
ar9003_mci_remote_reset(ah, true);
ar9003_mci_send_req_wake(ah, true);
if (ar9003_mci_wait_for_interrupt(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
AR_MCI_INTERRUPT_RX_MSG_SYS_WAKING, 500)) {
mci->bt_state = MCI_BT_AWAKE;
ar9003_mci_send_sys_waking(ah, true);
udelay(10);
REG_WRITE(ah, AR_MCI_BT_PRI0, 0xFFFFFFFF);
REG_WRITE(ah, AR_MCI_BT_PRI1, 0xFFFFFFFF);
REG_WRITE(ah, AR_MCI_BT_PRI2, 0xFFFFFFFF);
REG_WRITE(ah, AR_MCI_BT_PRI3, 0xFFFFFFFF);
REG_WRITE(ah, AR_MCI_BT_PRI, 0X000000FF);
REG_WRITE(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
AR_MCI_INTERRUPT_RX_MSG_CONT_RST);
REG_WRITE(ah, AR_MCI_INTERRUPT_RAW,
AR_MCI_INTERRUPT_BT_PRI);
if (mci->is_2g) {
ar9003_mci_send_lna_transfer(ah, true);
udelay(5);
}
if ((mci->is_2g && !mci->update_2g5g)) {
if (ar9003_mci_wait_for_interrupt(ah,
AR_MCI_INTERRUPT_RX_MSG_RAW,
AR_MCI_INTERRUPT_RX_MSG_LNA_INFO,
mci_timeout))
ath_dbg(common, MCI,
"MCI WLAN has control over the LNA & BT obeys it\n");
else
ath_dbg(common, MCI,
"MCI BT didn't respond to LNA_TRANS\n");
}
}
if ((mci->bt_state == MCI_BT_AWAKE) &&
(REG_READ_FIELD(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
AR_MCI_INTERRUPT_RX_MSG_SYS_WAKING)) &&
(REG_READ_FIELD(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
AR_MCI_INTERRUPT_RX_MSG_SYS_SLEEPING) == 0)) {
REG_WRITE(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
AR_MCI_INTERRUPT_RX_MSG_SYS_WAKING);
REG_WRITE(ah, AR_MCI_INTERRUPT_RAW,
AR_MCI_INTERRUPT_REMOTE_SLEEP_UPDATE);
}
REG_WRITE(ah, AR_MCI_INTERRUPT_EN, saved_mci_int_en);
}