/**
* @brief This function configures the system to enter Stop mode with RTC
* clocked by LSE or LSI for current consumption measurement purpose.
* STOP Mode with RTC clocked by LSE/LSI
* =====================================
* - RTC Clocked by LSE or LSI
* - Regulator in LP mode
* - HSI, HSE OFF and LSI OFF if not used as RTC Clock source
* - No IWDG
* - FLASH in deep power down mode
* - Automatic Wakeup using RTC clocked by LSE/LSI (~20s)
* @param None
* @retval None
*/
void StopMode_Measure(void)
{
__IO uint32_t index = 0;
GPIO_InitTypeDef GPIO_InitStructure;
NVIC_InitTypeDef NVIC_InitStructure;
EXTI_InitTypeDef EXTI_InitStructure;
/* Allow access to RTC */
PWR_BackupAccessCmd(ENABLE);
#if defined (RTC_CLOCK_SOURCE_LSI) /* LSI used as RTC source clock*/
/* The RTC Clock may varies due to LSI frequency dispersion. */
/* Enable the LSI OSC */
RCC_LSICmd(ENABLE);
/* Wait till LSI is ready */
while(RCC_GetFlagStatus(RCC_FLAG_LSIRDY) == RESET)
{
}
/* Select the RTC Clock Source */
RCC_RTCCLKConfig(RCC_RTCCLKSource_LSI);
#elif defined (RTC_CLOCK_SOURCE_LSE) /* LSE used as RTC source clock */
/* Enable the LSE OSC */
RCC_LSEConfig(RCC_LSE_ON);
/* Wait till LSE is ready */
while(RCC_GetFlagStatus(RCC_FLAG_LSERDY) == RESET)
{
}
/* Select the RTC Clock Source */
RCC_RTCCLKConfig(RCC_RTCCLKSource_LSE);
#else
#error Please select the RTC Clock source inside the main.c file
#endif /* RTC_CLOCK_SOURCE_LSI */
/* Enable the RTC Clock */
RCC_RTCCLKCmd(ENABLE);
/* Wait for RTC APB registers synchronisation */
RTC_WaitForSynchro();
/* Configure all GPIO as analog to reduce current consumption on non used IOs */
/* Enable GPIOs clock */
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA | RCC_AHB1Periph_GPIOB | RCC_AHB1Periph_GPIOC |
RCC_AHB1Periph_GPIOD | RCC_AHB1Periph_GPIOE | RCC_AHB1Periph_GPIOF |
RCC_AHB1Periph_GPIOG | RCC_AHB1Periph_GPIOH | RCC_AHB1Periph_GPIOI, ENABLE);
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_All;
GPIO_Init(GPIOC, &GPIO_InitStructure);
GPIO_Init(GPIOD, &GPIO_InitStructure);
GPIO_Init(GPIOE, &GPIO_InitStructure);
GPIO_Init(GPIOF, &GPIO_InitStructure);
GPIO_Init(GPIOG, &GPIO_InitStructure);
GPIO_Init(GPIOH, &GPIO_InitStructure);
GPIO_Init(GPIOI, &GPIO_InitStructure);
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_Init(GPIOB, &GPIO_InitStructure);
/* Disable GPIOs clock */
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA | RCC_AHB1Periph_GPIOB | RCC_AHB1Periph_GPIOC |
RCC_AHB1Periph_GPIOD | RCC_AHB1Periph_GPIOE | RCC_AHB1Periph_GPIOF |
RCC_AHB1Periph_GPIOG | RCC_AHB1Periph_GPIOH | RCC_AHB1Periph_GPIOI, DISABLE);
/* EXTI configuration *******************************************************/
EXTI_ClearITPendingBit(EXTI_Line22);
EXTI_InitStructure.EXTI_Line = EXTI_Line22;
EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
EXTI_InitStructure.EXTI_LineCmd = ENABLE;
EXTI_Init(&EXTI_InitStructure);
/* Enable the RTC Wakeup Interrupt */
NVIC_InitStructure.NVIC_IRQChannel = RTC_WKUP_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
/* RTC Wakeup Interrupt Generation: Clock Source: RTCCLK_Div16, Wakeup Time Base: ~20s
RTC Clock Source LSE 32.768KHz or LSI ~32KHz
Wakeup Time Base = (16 / (LSE or LSI)) * WakeUpCounter
*/
RTC_WakeUpClockConfig(RTC_WakeUpClock_RTCCLK_Div16);
RTC_SetWakeUpCounter(0xA000-1);
/* Enable the Wakeup Interrupt */
RTC_ITConfig(RTC_IT_WUT, ENABLE);
/* Enable Wakeup Counter */
RTC_WakeUpCmd(ENABLE);
/* FLASH Deep Power Down Mode enabled */
PWR_FlashPowerDownCmd(ENABLE);
/* Enter Stop Mode */
PWR_EnterSTOPMode(PWR_Regulator_LowPower, PWR_STOPEntry_WFI);
/* Initialize LED3 on STM32F429I-DISCO board */
STM_EVAL_LEDInit(LED3);
/* Infinite loop */
while (1)
{
/* Toggle The LED3 */
STM_EVAL_LEDToggle(LED3);
/* Inserted Delay */
for(index = 0; index < 0x5FF; index++);
}
}
/**
* @brief This function configures the system to enter Standby mode with RTC
* clocked by LSE or LSI for current consumption measurement purpose.
* STANDBY Mode with RTC clocked by LSE/LSI
* ========================================
* - RTC Clocked by LSE/LSI
* - IWDG OFF
* - Backup SRAM OFF
* - Automatic Wakeup using RTC clocked by LSE/LSI (after ~20s)
* @param None
* @retval None
*/
void StandbyRTCMode_Measure(void)
{
/* Allow access to RTC */
PWR_BackupAccessCmd(ENABLE);
#if defined (RTC_CLOCK_SOURCE_LSI) /* LSI used as RTC source clock*/
/* The RTC Clock may varies due to LSI frequency dispersion. */
/* Enable the LSI OSC */
RCC_LSICmd(ENABLE);
/* Wait till LSI is ready */
while(RCC_GetFlagStatus(RCC_FLAG_LSIRDY) == RESET)
{
}
/* Select the RTC Clock Source */
RCC_RTCCLKConfig(RCC_RTCCLKSource_LSI);
#elif defined (RTC_CLOCK_SOURCE_LSE) /* LSE used as RTC source clock */
/* Enable the LSE OSC */
RCC_LSEConfig(RCC_LSE_ON);
/* Wait till LSE is ready */
while(RCC_GetFlagStatus(RCC_FLAG_LSERDY) == RESET)
{
}
/* Select the RTC Clock Source */
RCC_RTCCLKConfig(RCC_RTCCLKSource_LSE);
#else
#error Please select the RTC Clock source inside the main.c file
#endif /* RTC_CLOCK_SOURCE_LSI */
/* Enable the RTC Clock */
RCC_RTCCLKCmd(ENABLE);
/* Wait for RTC APB registers synchronisation */
RTC_WaitForSynchro();
/* RTC Wakeup Interrupt Generation: Clock Source: RTCCLK_Div16, Wakeup Time Base: ~20s
RTC Clock Source LSE 32.768KHz or LSI ~32KHz
Wakeup Time Base = (16 / (LSE or LSI)) * WakeUpCounter
*/
RTC_WakeUpClockConfig(RTC_WakeUpClock_RTCCLK_Div16);
RTC_SetWakeUpCounter(0xA000-1);
/* Enable the Wakeup Interrupt */
RTC_ITConfig(RTC_IT_WUT, ENABLE);
/* Enable Wakeup Counter */
RTC_WakeUpCmd(ENABLE);
/* Clear WakeUp (WUTF) pending flag */
RTC_ClearFlag(RTC_FLAG_WUTF);
/* Request to enter STANDBY mode (Wake Up flag is cleared in PWR_EnterSTANDBYMode function) */
PWR_EnterSTANDBYMode();
/* Infinite loop */
while (1)
{
}
}
/**
* @brief Configure the RTC peripheral by selecting the clock source.
* @param None
* @retval None
*/
static void RTC_Config(void)
{
/* Enable the PWR clock */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);
/* Allow access to RTC */
PWR_BackupAccessCmd(ENABLE);
#if defined (RTC_CLOCK_SOURCE_LSI) /* LSI used as RTC source clock*/
/* The RTC Clock may varies due to LSI frequency dispersion. */
/* Enable the LSI OSC */
RCC_LSICmd(ENABLE);
/* Wait till LSI is ready */
while(RCC_GetFlagStatus(RCC_FLAG_LSIRDY) == RESET)
{
}
/* Select the RTC Clock Source */
RCC_RTCCLKConfig(RCC_RTCCLKSource_LSI);
/* ck_spre(1Hz) = RTCCLK(LSI) /(uwAsynchPrediv + 1)*(uwSynchPrediv + 1)*/
uwSynchPrediv = 0xFF;
uwAsynchPrediv = 0x7F;
#elif defined (RTC_CLOCK_SOURCE_LSE) /* LSE used as RTC source clock */
/* Enable the LSE OSC */
RCC_LSEConfig(RCC_LSE_ON);
/* Wait till LSE is ready */
while(RCC_GetFlagStatus(RCC_FLAG_LSERDY) == RESET)
{
}
/* Select the RTC Clock Source */
RCC_RTCCLKConfig(RCC_RTCCLKSource_LSE);
/* ck_spre(1Hz) = RTCCLK(LSE) /(uwAsynchPrediv + 1)*(uwSynchPrediv + 1)*/
uwSynchPrediv = 0xFF;
uwAsynchPrediv = 0x7F;
#else
#error Please select the RTC Clock source inside the main.c file
#endif /* RTC_CLOCK_SOURCE_LSI */
/* Enable the RTC Clock */
RCC_RTCCLKCmd(ENABLE);
/* Wait for RTC APB registers synchronisation */
RTC_WaitForSynchro();
/* Write to the first RTC Backup Data Register */
RTC_WriteBackupRegister(RTC_BKP_DR0, FIRST_DATA);
/* Display the new RCC BDCR and RTC TAFCR Registers */
LCD_UsrLog ("RTC Reconfig \n");
LCD_UsrLog ("RCC BDCR = 0x%x\n", RCC->BDCR);
LCD_UsrLog ("RTC TAFCR = 0x%x\n", RTC->TAFCR);
/* Set the Time */
RTC_TimeStructure.RTC_Hours = 0x08;
RTC_TimeStructure.RTC_Minutes = 0x00;
RTC_TimeStructure.RTC_Seconds = 0x00;
/* Set the Date */
RTC_DateStructure.RTC_Month = RTC_Month_January;
RTC_DateStructure.RTC_Date = 0x11;
RTC_DateStructure.RTC_Year = 0x13;
RTC_DateStructure.RTC_WeekDay = RTC_Weekday_Friday;
/* Calendar Configuration */
RTC_InitStructure.RTC_AsynchPrediv = uwAsynchPrediv;
RTC_InitStructure.RTC_SynchPrediv = uwSynchPrediv;
RTC_InitStructure.RTC_HourFormat = RTC_HourFormat_24;
RTC_Init(&RTC_InitStructure);
/* Set Current Time and Date */
RTC_SetTime(RTC_Format_BCD, &RTC_TimeStructure);
RTC_SetDate(RTC_Format_BCD, &RTC_DateStructure);
/* Configure the RTC Wakeup Clock source and Counter (Wakeup event each 1 second) */
RTC_WakeUpClockConfig(RTC_WakeUpClock_RTCCLK_Div16);
RTC_SetWakeUpCounter(0x7FF);
/* Enable the Wakeup Interrupt */
RTC_ITConfig(RTC_IT_WUT, ENABLE);
/* Enable Wakeup Counter */
RTC_WakeUpCmd(ENABLE);
/* Backup SRAM ***************************************************************/
/* Enable BKPRAM Clock */
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_BKPSRAM, ENABLE);
/* Write to Backup SRAM with 32-Bit Data */
for (uwIndex = 0x0; uwIndex < 0x1000; uwIndex += 4)
{
*(__IO uint32_t *) (BKPSRAM_BASE + uwIndex) = uwIndex;
}
/* Check the written Data */
for (uwIndex = 0x0; uwIndex < 0x1000; uwIndex += 4)
{
if ((*(__IO uint32_t *) (BKPSRAM_BASE + uwIndex)) != uwIndex)
{
uwErrorIndex++;
}
}
if(uwErrorIndex)
{
LCD_ErrLog ("BKP SRAM Number of errors = %d\n", uwErrorIndex);
}
else
{
LCD_UsrLog ("BKP SRAM write OK \n");
}
/* Enable the Backup SRAM low power Regulator to retain it's content in VBAT mode */
PWR_BackupRegulatorCmd(ENABLE);
/* Wait until the Backup SRAM low power Regulator is ready */
while(PWR_GetFlagStatus(PWR_FLAG_BRR) == RESET)
{
}
/* RTC Backup Data Registers **************************************************/
/* Write to RTC Backup Data Registers */
WriteToBackupReg(FIRST_DATA);
}
int main(void)
{
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32l1xx_md.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32l1xx.c file
*/
/* Configure Clocks for Application need */
RCC_Configuration();
/* Configure RTC Clocks */
RTC_Configuration();
/* Set internal voltage regulator to 1.8V */
PWR_VoltageScalingConfig(PWR_VoltageScaling_Range1);
/* Wait Until the Voltage Regulator is ready */
while (PWR_GetFlagStatus(PWR_FLAG_VOS) != RESET) ;
/* Enable debug features in low power modes (Sleep, STOP and STANDBY) */
#ifdef DEBUG_SWD_PIN
DBGMCU_Config(DBGMCU_SLEEP | DBGMCU_STOP | DBGMCU_STANDBY, ENABLE);
#endif
/* Configure SysTick IRQ and SysTick Timer to generate interrupts */
RCC_GetClocksFreq(&RCC_Clocks);
SysTick_Config(RCC_Clocks.HCLK_Frequency / 500);
/* Init I/O ports */
Init_GPIOs();
/* Initializes the LCD glass */
LCD_GLASS_Configure_GPIO();
LCD_GLASS_Init();
/* Display Welcome message */
LCD_GLASS_ScrollSentence(" ** TEMPERATURE SENSOR EXAMPLE ** ",1,SCROLL_SPEED);
/* Disable SysTick IRQ and SysTick Timer */
SysTick->CTRL &= ~ ( SysTick_CTRL_TICKINT_Msk | SysTick_CTRL_ENABLE_Msk );
/* Test user or factory temperature sensor calibration value */
if ( testFactoryCalibData() == SUCCESS ) getFactoryTSCalibData(&calibdata);
else if ( testUserCalibData() == SUCCESS ) calibdata = *USER_CALIB_DATA;
else {
/* User calibration or factory calibration TS data are not available */
calibdata.TS_CAL_1 = DEFAULT_COLD_VAL;
calibdata.TS_CAL_2 = DEFAULT_HOT_VAL;
writeCalibData(&calibdata);
calibdata = *USER_CALIB_DATA;
}
/* Configure Wakeup from sleep using RTC event*/
configureWakeup();
/* Configure direct memory access for ADC usage*/
configureDMA();
/* Configure ADC for temperature sensor value conversion */
configureADC_Temp();
while(1) {
/* Re-enable DMA and ADC conf and start Temperature Data acquisition */
acquireTemperatureData();
/* Stay in SLEEP mode untill the data are acquired by ADC */
__WFI();
/* for DEBUG purpose uncomment the following line and comment the __WFI call to do not enter STOP mode */
// while (!flag_ADCDMA_TransferComplete);
/* Disable ADC, DMA and clock*/
powerDownADC_Temper();
/* Process mesured Temperature data - calculate average temperature value in °C */
processTempData();
if (flag_UserButton == TRUE) {
clearUserButtonFlag();
if (CurrentlyDisplayed == Display_TemperatureDegC)
CurrentlyDisplayed = Display_ADCval;
else
CurrentlyDisplayed = Display_TemperatureDegC;
}
if (CurrentlyDisplayed == Display_TemperatureDegC) {
/* print average temperature value in °C */
sprintf(strDisp, "%d °C", temperature_C );
} else {
/* print result of ADC conversion */
sprintf(strDisp, "> %d", tempAVG );
}
LCD_GLASS_Clear();
LCD_GLASS_DisplayString( (unsigned char *) strDisp );
/* Enable RTC Wakeup */
RTC_WakeUpCmd(ENABLE);
/* Clear WakeUp flag */
PWR_ClearFlag(PWR_FLAG_WU);
/* Enter in wait for interrupt stop mode*/
PWR_EnterSTOPMode(PWR_Regulator_LowPower, PWR_STOPEntry_WFI);
RCC_Configuration(); // reinitialize clock
/* After Wake up : Disable Wake up from RTC*/
RTC_WakeUpCmd(DISABLE);
}
}
void RTC_Configuration(void)
{
/* Enable the PWR APB1 Clock Interface */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);
/* Allow access to BKP Domain */
PWR_BackupAccessCmd(ENABLE);
if (RTC_ReadBackupRegister(RTC_BKP_DR2) != 0xA5A5) {
/* Enable the PWR clock */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);
/* Allow access to RTC */
PWR_BackupAccessCmd(ENABLE);
#if defined (RTC_CLOCK_SOURCE_LSI) /* LSI used as RTC source clock*/
/* The RTC Clock may varies due to LSI frequency dispersion. */
/* Enable the LSI OSC */
RCC_LSICmd(ENABLE);
/* Wait till LSI is ready */
while(RCC_GetFlagStatus(RCC_FLAG_LSIRDY) == RESET)
{
}
/* Select the RTC Clock Source */
RCC_RTCCLKConfig(RCC_RTCCLKSource_LSI);
SynchPrediv = 0xFF;
AsynchPrediv = 0x7F;
#elif defined (RTC_CLOCK_SOURCE_LSE) /* LSE used as RTC source clock */
/* Enable the LSE OSC */
RCC_LSEConfig(RCC_LSE_ON);
/* Wait till LSE is ready */
while(RCC_GetFlagStatus(RCC_FLAG_LSERDY) == RESET)
{
}
/* Select the RTC Clock Source */
RCC_RTCCLKConfig(RCC_RTCCLKSource_LSE);
SynchPrediv = 0xFF;
AsynchPrediv = 0x7F;
#else
#error Please select the RTC Clock source inside the main.c file
#endif /* RTC_CLOCK_SOURCE_LSI */
/* Enable the RTC Clock */
RCC_RTCCLKCmd(ENABLE);
/* Wait for RTC APB registers synchronisation */
RTC_WaitForSynchro();
/* Allow access to BKP Domain */
PWR_BackupAccessCmd(ENABLE);
/* Write to the first RTC Backup Data Register */
RTC_WriteBackupRegister(RTC_BKP_DR2,0xA5A5);
/* Set the Time */
RTC_TimeStructure.RTC_Hours = 22;
RTC_TimeStructure.RTC_Minutes = 11;
RTC_TimeStructure.RTC_Seconds = 00;
/* Set the Date */
RTC_DateStructure.RTC_Month = 4;
RTC_DateStructure.RTC_Date = 29;
RTC_DateStructure.RTC_Year = 11;
RTC_DateStructure.RTC_WeekDay = RTC_Weekday_Friday;
/* Calendar Configuration */
RTC_InitStructure.RTC_AsynchPrediv = AsynchPrediv;
RTC_InitStructure.RTC_SynchPrediv = SynchPrediv;
RTC_InitStructure.RTC_HourFormat = RTC_HourFormat_24;
RTC_Init(&RTC_InitStructure);
/* Set Current Time and Date */
RTC_SetTime(RTC_Format_BIN, &RTC_TimeStructure);
RTC_SetDate(RTC_Format_BIN, &RTC_DateStructure);
#if 0
/* Configure the RTC Wakeup Clock source and Counter (Wakeup event each 1 second) */
RTC_WakeUpClockConfig(RTC_WakeUpClock_RTCCLK_Div16);
RTC_SetWakeUpCounter(0x7FF);
/* Enable the Wakeup Interrupt */
RTC_ITConfig(RTC_IT_WUT, ENABLE);
/* Enable Wakeup Counter */
RTC_WakeUpCmd(ENABLE);
#endif
/* Backup SRAM ***************************************************************/
/* Enable BKPRAM Clock */
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_BKPSRAM, ENABLE);
/* Enable the Backup SRAM low power Regulator to retain it's content in VBAT mode */
PWR_BackupRegulatorCmd(ENABLE);
/* Wait until the Backup SRAM low power Regulator is ready */
while(PWR_GetFlagStatus(PWR_FLAG_BRR) == RESET)
{
}
}
else{
/* Enable the PWR clock */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);
/* Allow access to RTC */
PWR_BackupAccessCmd(ENABLE);
/* Wait for RTC APB registers synchronisation */
RTC_WaitForSynchro();
/* Clear the Wakeup Interrupt */
RTC_ClearITPendingBit(RTC_IT_WUT);
/* Backup SRAM ***************************************************************/
/* Enable BKPSRAM Clock */
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_BKPSRAM, ENABLE);
}
}
/**
* @brief Configure the RTC peripheral by selecting the clock source.
* @param None
* @retval None
*/
void RTC_Config(void)
{
NVIC_InitTypeDef NVIC_InitStructure;
EXTI_InitTypeDef EXTI_InitStructure;
/* Enable the PWR clock */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG , ENABLE);
/* Allow access to RTC */
//PWR_RTCAccessCmd(ENABLE);
//Enable the LSE OSC
RCC_LSEConfig(RCC_LSE_ON);
//wait until LSE is ready
while(RCC_GetFlagStatus(RCC_FLAG_LSERDY) == RESET) {}
//Select RTC clk source
RCC_RTCCLKConfig(RCC_RTCCLKSource_LSE);
//SynchPrediv = 0xFF;
//AsynchPrediv = 0x7F;
/* Enable the RTC Clock */
RCC_RTCCLKCmd(ENABLE);
/* Wait for RTC APB registers synchronisation */
RTC_WaitForSynchro();
RTC_InitStructure.RTC_AsynchPrediv = 0x7F;
RTC_InitStructure.RTC_SynchPrediv = 0xFF; /* (32KHz / 128) - 1 = 0xFF*/
RTC_InitStructure.RTC_HourFormat = RTC_HourFormat_24;
RTC_Init(&RTC_InitStructure);
RTC_WakeUpCmd(DISABLE);
/* EXTI configuration *******************************************************/
EXTI_ClearITPendingBit(EXTI_Line20);
EXTI_InitStructure.EXTI_Line = EXTI_Line20;
EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
EXTI_InitStructure.EXTI_LineCmd = ENABLE;
EXTI_Init(&EXTI_InitStructure);
/* Enable the RTC Wakeup Interrupt */
NVIC_InitStructure.NVIC_IRQChannel = RTC_WKUP_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
NVIC_SetPriority(RTC_WKUP_IRQn, INT_PRIORITY_WKUP);
//RTCCLK=32768Hz ; div=16 =>2048Hz
RTC_WakeUpClockConfig(RTC_WakeUpClock_RTCCLK_Div16);
//div 256 =>8Hz ~ 125ms
RTC_SetWakeUpCounter(0xFF);
RTC_ClearITPendingBit(RTC_IT_WUT);
EXTI_ClearITPendingBit(EXTI_Line20);
/* Enable the RTC Wakeup Interrupt */
RTC_ITConfig(RTC_IT_WUT, ENABLE);
/* Enable Wakeup Counter */
RTC_WakeUpCmd(ENABLE);
//PWR_RTCAccessCmd(DISABLE);
//disable PWR clock
//RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, DISABLE);
}
/**
* @brief This function configures the system to enter Standby mode with RTC
* clocked by LSI for current consumption measurement purpose.
* STANDBY Mode with RTC clocked by LSI
* ====================================
* - RTC Clocked by LSI
* - IWDG OFF
* - Current Consumption ~1.1uA
* - Automatic Wakeup using RTC clocked by LSI (after ~4s)
* @param None
* @retval None
*/
void StandbyRTCLSIMode_Measure(void)
{
/* Configure Key Button*/
STM_EVAL_PBInit(BUTTON_KEY,BUTTON_MODE_GPIO);
/* Wait Until Key button pressed */
while(STM_EVAL_PBGetState(BUTTON_KEY) == RESET)
{
}
/* Wait Until Key button pressed */
while(STM_EVAL_PBGetState(BUTTON_KEY) != RESET)
{
}
/* Allow access to RTC */
PWR_RTCAccessCmd(ENABLE);
/*!< LSI Enable */
RCC_LSICmd(ENABLE);
/*!< Wait till LSI is ready */
while (RCC_GetFlagStatus(RCC_FLAG_LSIRDY) == RESET)
{}
/*!< RTC Clock Source Selection */
RCC_RTCCLKConfig(RCC_RTCCLKSource_LSI);
/* Enable the RTC Clock */
RCC_RTCCLKCmd(ENABLE);
/* Wait for RTC APB registers synchronisation */
RTC_WaitForSynchro();
/* Enable Ultra low power mode */
PWR_UltraLowPowerCmd(ENABLE);
/* RTC Wakeup Interrupt Generation: Clock Source: RTCCLK_Div16, Wakeup Time Base: ~4s
RTC Clock Source LSI ~37KHz
*/
RTC_WakeUpClockConfig(RTC_WakeUpClock_RTCCLK_Div16);
RTC_SetWakeUpCounter(0x2421);
/* Clear PWR WakeUp flag */
PWR_ClearFlag(PWR_FLAG_WU);
/* Clear RTC WakeUp (WUTF) flag */
RTC_ClearFlag(RTC_FLAG_WUTF);
/* Enable the Wakeup Interrupt */
RTC_ITConfig(RTC_IT_WUT, ENABLE);
/* Enable Wakeup Counter */
RTC_WakeUpCmd(ENABLE);
/* Request to enter STANDBY mode */
PWR_EnterSTANDBYMode();
/* Infinite loop */
while (1)
{
}
}
void EnRtcInter(void){
NVIC_InitTypeDef NVIC_InitStructure;
EXTI_InitTypeDef EXTI_InitStructure;
RTC_InitTypeDef RTC_InitStructure;
/* Enable the PWR clock */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);
/* Allow access to RTC */
PWR_RTCAccessCmd(ENABLE);
/* LSI used as RTC source clock */
/* The RTC Clock may varies due to LSI frequency dispersion. */
/* Enable the LSI OSC */
RCC_LSICmd(ENABLE);
/* Wait till LSI is ready */
while(RCC_GetFlagStatus(RCC_FLAG_LSIRDY) == RESET);
/* Select the RTC Clock Source */
RCC_RTCCLKConfig(RCC_RTCCLKSource_LSI);
/* Enable the RTC Clock */
RCC_RTCCLKCmd(ENABLE);
/* Wait for RTC APB registers synchronisation */
RTC_WaitForSynchro();
/* Calendar Configuration */
RTC_InitStructure.RTC_AsynchPrediv = 0x7F;
RTC_InitStructure.RTC_SynchPrediv = 0x120; /* (37KHz / 128) - 1 = 0x120*/
RTC_InitStructure.RTC_HourFormat = RTC_HourFormat_24;
RTC_Init(&RTC_InitStructure);
/*
To enable the RTC Wakeup interrupt, the following sequence is required:
1. Configure and enable the EXTI Line 20 in interrupt mode and select the rising edge
sensitivity.
2. Configure and enable the RTC_WKUP IRQ channel in the NVIC.
3. Configure the RTC to generate the RTC wakeup timer event.
System reset, as well as low power modes (Sleep, Stop and Standby) have no influence on
the wakeup timer.
*/
/* EXTI configuration *******************************************************/
EXTI_ClearITPendingBit(EXTI_Line20);
EXTI_InitStructure.EXTI_Line = EXTI_Line20;
EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
EXTI_InitStructure.EXTI_LineCmd = ENABLE;
EXTI_Init(&EXTI_InitStructure);
/* Enable the RTC Wakeup Interrupt */
NVIC_InitStructure.NVIC_IRQChannel = RTC_WKUP_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
RTC_WakeUpCmd(DISABLE);
PWR_RTCAccessCmd(ENABLE);
RTC_WakeUpClockConfig(RTC_WakeUpClock_CK_SPRE_16bits);
RTC_SetWakeUpCounter(readintvalue(SLEEPTIME_add)); //0x01f4
//The WUTF flag must then be cleared by software.
RTC_ClearITPendingBit(RTC_IT_WUT); //ClearITPendingBit clears also the flag
//RTC_ClearFlag(RTC_FLAG_WUTF); //MANDATORY!
RTC_ITConfig(RTC_IT_WUT, ENABLE); //enable interrupt
RTC_WakeUpCmd(ENABLE);
PWR_RTCAccessCmd(DISABLE); //just in case
}
void TM_RTC_Interrupts(TM_RTC_Int_t int_value) {
uint32_t int_val;
/* Clear pending bit */
EXTI_ClearITPendingBit(EXTI_Line22);
/* NVIC init for RTC */
NVIC_InitStruct.NVIC_IRQChannel = RTC_WKUP_IRQn;
NVIC_InitStruct.NVIC_IRQChannelPreemptionPriority = RTC_PRIORITY;
NVIC_InitStruct.NVIC_IRQChannelSubPriority = RTC_WAKEUP_SUBPRIORITY;
/* RTC connected to EXTI_Line22 */
EXTI_InitStruct.EXTI_Line = EXTI_Line22;
EXTI_InitStruct.EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStruct.EXTI_Trigger = EXTI_Trigger_Rising;
if (int_value == TM_RTC_Int_Disable) {
/* Disable wakeup interrupt */
RTC_WakeUpCmd(DISABLE);
/* Disable RTC interrupt flag */
RTC_ITConfig(RTC_IT_WUT, DISABLE);
/* Disable NVIC */
NVIC_InitStruct.NVIC_IRQChannelCmd = DISABLE;
NVIC_Init(&NVIC_InitStruct);
/* Disable EXT1 interrupt */
EXTI_InitStruct.EXTI_LineCmd = DISABLE;
EXTI_Init(&EXTI_InitStruct);
} else {
/* Enable NVIC */
NVIC_InitStruct.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStruct);
/* Enable EXT1 interrupt */
EXTI_InitStruct.EXTI_LineCmd = ENABLE;
EXTI_Init(&EXTI_InitStruct);
/* First disable wake up command */
RTC_WakeUpCmd(DISABLE);
if (int_value == TM_RTC_Int_60s) {
int_val = 0x3BFFF; /* 60 seconds = 60 * 4096 / 1 = 245760 */
} else if (int_value == TM_RTC_Int_30s) {
int_val = 0x1DFFF; /* 30 seconds */
} else if (int_value == TM_RTC_Int_15s) {
int_val = 0xEFFF; /* 15 seconds */
} else if (int_value == TM_RTC_Int_10s) {
int_val = 0x9FFF; /* 10 seconds */
} else if (int_value == TM_RTC_Int_5s) {
int_val = 0x4FFF; /* 5 seconds */
} else if (int_value == TM_RTC_Int_2s) {
int_val = 0x1FFF; /* 2 seconds */
} else if (int_value == TM_RTC_Int_1s) {
int_val = 0x0FFF; /* 1 second */
} else if (int_value == TM_RTC_Int_500ms) {
int_val = 0x7FF; /* 500 ms */
} else if (int_value == TM_RTC_Int_250ms) {
int_val = 0x3FF; /* 250 ms */
} else if (int_value == TM_RTC_Int_125ms) {
int_val = 0x1FF; /* 125 ms */
}
/* Clock divided by 8, 32768 / 8 = 4068 */
/* 4096 ticks for 1second interrupt */
RTC_WakeUpClockConfig(RTC_WakeUpClock_RTCCLK_Div8);
/* Set RTC wakeup counter */
RTC_SetWakeUpCounter(int_val);
/* Enable wakeup interrupt */
RTC_ITConfig(RTC_IT_WUT, ENABLE);
/* Enable wakeup command */
RTC_WakeUpCmd(ENABLE);
}
}
/**
* @brief This function configures the system to enter Stop mode with RTC
* clocked by LSI for current consumption measurement purpose.
* STOP Mode with RTC clocked by LSI
* =================================
* - RTC Clocked by LSI
* - Regulator in LP mode
* - HSI and HSE OFF
* - No IWDG
* - Current Consumption ~1.3uA
* - Automatic Wakeup using RTC clocked by LSI (after ~4s)
* @param None
* @retval None
*/
void StopRTCLSIMode_Measure(void)
{
NVIC_InitTypeDef NVIC_InitStructure;
EXTI_InitTypeDef EXTI_InitStructure;
/* Allow access to RTC */
PWR_RTCAccessCmd(ENABLE);
/*!< LSI Enable */
RCC_LSICmd(ENABLE);
/*!< Wait till LSI is ready */
while (RCC_GetFlagStatus(RCC_FLAG_LSIRDY) == RESET)
{}
/*!< RTC Clock Source Selection */
RCC_RTCCLKConfig(RCC_RTCCLKSource_LSI);
/* Enable the RTC Clock */
RCC_RTCCLKCmd(ENABLE);
/* Wait for RTC APB registers synchronisation */
RTC_WaitForSynchro();
/* Configure all GPIO as analog to reduce current consumption on non used IOs */
/* Enable GPIOs clock */
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA | RCC_AHBPeriph_GPIOB | RCC_AHBPeriph_GPIOC |
RCC_AHBPeriph_GPIOD | RCC_AHBPeriph_GPIOE | RCC_AHBPeriph_GPIOH |
RCC_AHBPeriph_GPIOF | RCC_AHBPeriph_GPIOG, ENABLE);
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_40MHz;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_All;
GPIO_Init(GPIOC, &GPIO_InitStructure);
GPIO_Init(GPIOD, &GPIO_InitStructure);
GPIO_Init(GPIOE, &GPIO_InitStructure);
GPIO_Init(GPIOH, &GPIO_InitStructure);
GPIO_Init(GPIOG, &GPIO_InitStructure);
GPIO_Init(GPIOF, &GPIO_InitStructure);
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_Init(GPIOB, &GPIO_InitStructure);
/* Disable GPIOs clock */
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA | RCC_AHBPeriph_GPIOB | RCC_AHBPeriph_GPIOC |
RCC_AHBPeriph_GPIOD | RCC_AHBPeriph_GPIOE | RCC_AHBPeriph_GPIOH |
RCC_AHBPeriph_GPIOF | RCC_AHBPeriph_GPIOG, DISABLE);
/* Configure Key Button*/
STM_EVAL_PBInit(BUTTON_KEY,BUTTON_MODE_GPIO);
/* Wait Until Key button pressed */
while(STM_EVAL_PBGetState(BUTTON_KEY) == RESET)
{
}
/* Wait Until Key button pressed */
while(STM_EVAL_PBGetState(BUTTON_KEY) != RESET)
{
}
/* EXTI configuration *******************************************************/
EXTI_ClearITPendingBit(EXTI_Line20);
EXTI_InitStructure.EXTI_Line = EXTI_Line20;
EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
EXTI_InitStructure.EXTI_LineCmd = ENABLE;
EXTI_Init(&EXTI_InitStructure);
/* Enable the RTC Wakeup Interrupt */
NVIC_InitStructure.NVIC_IRQChannel = RTC_WKUP_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
/* RTC Wakeup Interrupt Generation: Clock Source: RTCCLK_Div16, Wakeup Time Base: ~4s
RTC Clock Source LSI ~37KHz
*/
RTC_WakeUpClockConfig(RTC_WakeUpClock_RTCCLK_Div16);
RTC_SetWakeUpCounter(0x2421);
/* Enable the Wakeup Interrupt */
RTC_ITConfig(RTC_IT_WUT, ENABLE);
/* Enable Ultra low power mode */
PWR_UltraLowPowerCmd(ENABLE);
/* Enable Wakeup Counter */
RTC_WakeUpCmd(ENABLE);
/* Enter Stop Mode */
PWR_EnterSTOPMode(PWR_Regulator_LowPower, PWR_STOPEntry_WFI);
/* Infinite loop */
while (1)
{
/* Toggle The LED1 */
STM_EVAL_LEDToggle(LED1);
/* Inserted Delay */
for(index = 0; index < 0x5FF; index++);
}
}
void UB_RTC_SetWakeUpInterrupt(RTC_WAKEUP_t wakeup)
{
NVIC_InitTypeDef NVIC_InitStructure;
EXTI_InitTypeDef EXTI_InitStructure;
uint32_t wakeup_time=0x7FF;
if(wakeup==RTC_WAKEUP_STOP) {
// WakeUp-Interrupt abschalten
RTC_WakeUpCmd(DISABLE);
// disable Interrupt
RTC_ITConfig(RTC_IT_WUT, DISABLE);
// NVIC disable
NVIC_InitStructure.NVIC_IRQChannel = RTC_WKUP_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = DISABLE;
NVIC_Init(&NVIC_InitStructure);
// ext Interrupt 22 disable
EXTI_ClearITPendingBit(EXTI_Line22);
EXTI_InitStructure.EXTI_Line = EXTI_Line22;
EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
EXTI_InitStructure.EXTI_LineCmd = DISABLE;
EXTI_Init(&EXTI_InitStructure);
}
else {
// WakeUp-Interrupt einschalten
// NVIC init
NVIC_InitStructure.NVIC_IRQChannel = RTC_WKUP_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
// ext Interrupt 22 einstellen (fuer WakeUp)
EXTI_ClearITPendingBit(EXTI_Line22);
EXTI_InitStructure.EXTI_Line = EXTI_Line22;
EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
EXTI_InitStructure.EXTI_LineCmd = ENABLE;
EXTI_Init(&EXTI_InitStructure);
// zum einstellen muss Wakup disabled sein
RTC_WakeUpCmd(DISABLE);
if(wakeup==RTC_WAKEUP_30s) wakeup_time=0xEFFF;
if(wakeup==RTC_WAKEUP_10s) wakeup_time=0x4FFF;
if(wakeup==RTC_WAKEUP_5s) wakeup_time=0x27FF;
if(wakeup==RTC_WAKEUP_1s) wakeup_time=0x7FF;
if(wakeup==RTC_WAKEUP_500ms) wakeup_time=0x3FF;
if(wakeup==RTC_WAKEUP_250ms) wakeup_time=0x1FF;
if(wakeup==RTC_WAKEUP_125ms) wakeup_time=0xFF;
// Teiler 16 => 32,768kHz:16 => 2048 Hz
RTC_WakeUpClockConfig(RTC_WakeUpClock_RTCCLK_Div16);
// WakeUp Counter einstellen
RTC_SetWakeUpCounter(wakeup_time);
// enable Interrupt
RTC_ITConfig(RTC_IT_WUT, ENABLE);
// enable Wakeup
RTC_WakeUpCmd(ENABLE);
}
}
/**
* @brief Configure the RTC peripheral by selecting the clock source.
* @param None
* @retval None
*/
void RTC_Config(void)
{
NVIC_InitTypeDef NVIC_InitStructure;
EXTI_InitTypeDef EXTI_InitStructure;
/* Enable the PWR clock */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);
/* Allow access to RTC */
PWR_RTCAccessCmd(ENABLE);
/* LSI used as RTC source clock */
/* The RTC Clock may varies due to LSI frequency dispersion. */
/* Enable the LSI OSC */
RCC_LSICmd(ENABLE);
/* Wait till LSI is ready */
while(RCC_GetFlagStatus(RCC_FLAG_LSIRDY) == RESET)
{
}
/* Select the RTC Clock Source */
RCC_RTCCLKConfig(RCC_RTCCLKSource_LSI);
/* Enable the RTC Clock */
RCC_RTCCLKCmd(ENABLE);
/* Wait for RTC APB registers synchronisation */
RTC_WaitForSynchro();
/* Calendar Configuration */
RTC_InitStructure.RTC_AsynchPrediv = 0x7F;
RTC_InitStructure.RTC_SynchPrediv = 0x120; /* (37KHz / 128) - 1 = 0x120*/
RTC_InitStructure.RTC_HourFormat = RTC_HourFormat_24;
RTC_Init(&RTC_InitStructure);
/* EXTI configuration *******************************************************/
EXTI_ClearITPendingBit(EXTI_Line20);
EXTI_InitStructure.EXTI_Line = EXTI_Line20;
EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
EXTI_InitStructure.EXTI_LineCmd = ENABLE;
EXTI_Init(&EXTI_InitStructure);
/* Enable the RTC Wakeup Interrupt */
NVIC_InitStructure.NVIC_IRQChannel = RTC_WKUP_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
/* Configure the RTC WakeUp Clock source: CK_SPRE (1Hz) */
RTC_WakeUpClockConfig(RTC_WakeUpClock_CK_SPRE_16bits);
RTC_SetWakeUpCounter(0x0);
/* Enable the RTC Wakeup Interrupt */
RTC_ITConfig(RTC_IT_WUT, ENABLE);
/* Enable Wakeup Counter */
RTC_WakeUpCmd(ENABLE);
}
static void RTC_Config32768Internal(void) {
NVIC_InitTypeDef NVIC_InitStructure;
EXTI_InitTypeDef EXTI_InitStructure;
RTC_DateTypeDef RTC_DateStruct;
//uint8_t yr;
/* Enable the PWR clock */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);
/* SYSCFG Peripheral clock enable */
RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE);
PWR_DeInit();
/* Allow access to RTC */
PWR_RTCAccessCmd(ENABLE);
/* LSI used as RTC source clock */
/* The RTC Clock may varies due to LSI frequency dispersion. */
/* Enable the LSI OSC */
//RCC_LSICmd(ENABLE);
RCC_RTCCLKConfig(RCC_RTCCLKSource_LSE);
RCC_LSEConfig(RCC_LSE_ON);
/* Wait till LSI is ready */
//while(RCC_GetFlagStatus(RCC_FLAG_LSIRDY) == RESET)
while (RCC_GetFlagStatus(RCC_FLAG_LSERDY) == RESET) {
}
/* Select the RTC Clock Source */
//RCC_RTCCLKConfig(RCC_RTCCLKSource_LSI);
/* Enable the RTC Clock */
RCC_RTCCLKCmd(ENABLE);
/* Wait for RTC APB registers synchronisation */
RTC_WaitForSynchro();
// LSE 32768
RTC_InitStructure.RTC_AsynchPrediv = 127;
RTC_InitStructure.RTC_SynchPrediv = 255;
/* Calendar Configuration with LSI supposed at 37KHz */
//RTC_InitStructure.RTC_AsynchPrediv = 124;
//RTC_InitStructure.RTC_SynchPrediv = 295; /* (32KHz / 128) - 1 = 0xFF*/
RTC_InitStructure.RTC_HourFormat = RTC_HourFormat_24;
RTC_Init(&RTC_InitStructure);
/* Set the time to 05h 20mn 00s AM */
RTC_TimeStructure.RTC_H12 = RTC_H12_PM;
RTC_TimeStructure.RTC_Hours = 0x23;
RTC_TimeStructure.RTC_Minutes = 0x59;
RTC_TimeStructure.RTC_Seconds = 0x50;
RTC_SetTime(RTC_Format_BCD, &RTC_TimeStructure);
RTC_DateStruct.RTC_Year = 14;
RTC_DateStruct.RTC_Month = 10;
RTC_DateStruct.RTC_Date = 4;
RTC_DateStruct.RTC_WeekDay = 6;
//day = 5;
RTC_SetDate(RTC_Format_BIN, &RTC_DateStruct);
//RTC_GetDate(RTC_Format_BCD, &RTC_DateStruct);
//yr = RTC_DateStruct.RTC_Year;
/* EXTI configuration *******************************************************/
EXTI_ClearITPendingBit(EXTI_Line20);
EXTI_InitStructure.EXTI_Line = EXTI_Line20;
EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
EXTI_InitStructure.EXTI_LineCmd = ENABLE;
EXTI_Init(&EXTI_InitStructure);
// Configuring RTC_WakeUp interrupt
NVIC_InitStructure.NVIC_IRQChannel = RTC_WKUP_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
// RTC Wakeup Configuration
RTC_WakeUpClockConfig(RTC_WakeUpClock_CK_SPRE_16bits);
// RTC Set WakeUp Counter
RTC_SetWakeUpCounter(0);
// Enabling RTC_WakeUp interrupt
RTC_ITConfig(RTC_IT_WUT, ENABLE);
// Disabling Alarm Flags
RTC_AlarmCmd(RTC_Alarm_A, DISABLE);
RTC_AlarmCmd(RTC_Alarm_B, DISABLE);
// RTC Enable the Wakeup Function
RTC_WakeUpCmd(ENABLE);
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32l1xx_xx.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32l1xx.c file
*/
/* RTC configuration -------------------------------------------------------*/
RTC_Config();
/* Configure the SysTick to generate an interrupt each 250 ms */
SysTickConfig();
/* LCD GLASS Initialization */
LCD_GLASS_Init();
/* Clear the LCD GLASS */
LCD_GLASS_Clear();
/* Configure STM32L152-EVAL LED1 and LED2 as Output push-pull */
STM_EVAL_LEDInit(LED1);
STM_EVAL_LEDInit(LED2);
while (1)
{
/* Display " STM32L " string on LCD glass in scrolling mode */
LCD_GLASS_ScrollString(LCD_String, SCROLL_NUM, SCROLL_SPEED);
/* Display String on the LCD */
#ifdef USE_STM32L152D_EVAL
LCD_GLASS_DisplayString("STOPMOD");
#else
LCD_GLASS_DisplayString("STOPMODE");
#endif
/* Enable Wakeup Counter */
RTC_WakeUpCmd(ENABLE);
/* Enter Stop Mode */
PWR_EnterSTOPMode(PWR_Regulator_LowPower, PWR_STOPEntry_WFI);
/* Enable Wakeup Counter */
RTC_WakeUpCmd(DISABLE);
/* After wake-up from STOP reconfigure the system clock */
/* Enable HSE */
RCC_HSEConfig(RCC_HSE_ON);
/* Wait till HSE is ready */
while (RCC_GetFlagStatus(RCC_FLAG_HSERDY) == RESET)
{}
/* Enable PLL */
RCC_PLLCmd(ENABLE);
/* Wait till PLL is ready */
while (RCC_GetFlagStatus(RCC_FLAG_PLLRDY) == RESET)
{}
/* Select PLL as system clock source */
RCC_SYSCLKConfig(RCC_SYSCLKSource_PLLCLK);
/* Wait till PLL is used as system clock source */
while (RCC_GetSYSCLKSource() != 0x0C)
{}
}
}
OSStatus platform_mcu_powersave_init(void)
{
#ifndef MICO_DISABLE_MCU_POWERSAVE
#if 0 // Magicoe
EXTI_InitTypeDef EXTI_InitStructure;
RTC_InitTypeDef RTC_InitStruct;
//RTC_DeInit( );
RTC_InitStruct.RTC_HourFormat = RTC_HourFormat_24;
/* RTC ticks every second */
RTC_InitStruct.RTC_AsynchPrediv = 0x7F;
RTC_InitStruct.RTC_SynchPrediv = 0xFF;
RTC_Init( &RTC_InitStruct );
/* Enable the PWR clock */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);
/* RTC clock source configuration ------------------------------------------*/
/* Allow access to BKP Domain */
PWR_BackupAccessCmd(ENABLE);
PWR_BackupRegulatorCmd(ENABLE);
/* Enable the LSE OSC */
RCC_LSEConfig(RCC_LSE_ON);
/* Wait till LSE is ready */
while(RCC_GetFlagStatus(RCC_FLAG_LSERDY) == RESET)
{
}
/* Select the RTC Clock Source */
RCC_RTCCLKConfig(RCC_RTCCLKSource_LSE);
/* Enable the RTC Clock */
RCC_RTCCLKCmd(ENABLE);
/* RTC configuration -------------------------------------------------------*/
/* Wait for RTC APB registers synchronisation */
RTC_WaitForSynchro();
RTC_WakeUpCmd( DISABLE );
EXTI_ClearITPendingBit( RTC_INTERRUPT_EXTI_LINE );
PWR_ClearFlag(PWR_FLAG_WU);
RTC_ClearFlag(RTC_FLAG_WUTF);
RTC_WakeUpClockConfig(RTC_WakeUpClock_RTCCLK_Div2);
EXTI_ClearITPendingBit( RTC_INTERRUPT_EXTI_LINE );
EXTI_InitStructure.EXTI_Line = RTC_INTERRUPT_EXTI_LINE;
EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
EXTI_InitStructure.EXTI_LineCmd = ENABLE;
EXTI_Init(&EXTI_InitStructure);
NVIC_EnableIRQ( RTC_WKUP_IRQn );
RTC_ITConfig(RTC_IT_WUT, DISABLE);
/* Prepare Stop-Mode but leave disabled */
//PWR_ClearFlag(PWR_FLAG_WU);
PWR->CR |= PWR_CR_LPDS;
PWR->CR &= (unsigned long)(~(PWR_CR_PDDS));
SCB->SCR |= ((unsigned long)SCB_SCR_SLEEPDEEP_Msk);
#ifdef USE_RTC_BKP
if (RTC_ReadBackupRegister(RTC_BKP_DR0) != USE_RTC_BKP) {
/* set it to 12:20:30 08/04/2013 monday */
platform_rtc_set_time(&default_rtc_time);
RTC_WriteBackupRegister(RTC_BKP_DR0, USE_RTC_BKP);
}
#else
//#ifdef RTC_ENABLED
/* application must have mico_application_default_time structure declared somewhere, otherwise it wont compile */
/* write default application time inside rtc */
platform_rtc_set_time( &default_rtc_time );
//#endif /* RTC_ENABLED */
#endif
#endif
return kNoErr;
#else
return kUnsupportedErr;
#endif
}
