/**
* \brief Write to the FRAM chip.
* \param address The index of the byte to start writing to.
* \param len The number of bytes to write.
* \param buf A buffer of values to write.
* \return 0 on success, -1 on error
*
* Writes len bytes to the FRAM chip starting at address.
*/
int
fm25lb_write(uint16_t address, uint16_t len, uint8_t *buf)
{
uint16_t i;
spi_set_mode(SSI_CR0_FRF_MOTOROLA, SSI_CR0_SPO, SSI_CR0_SPH, 8);
SPI_CS_CLR(FM25LB_CS_N_PORT_NUM, FM25LB_CS_N_PIN);
/* Send the WRITE ENABLE command to allow writing to the FRAM */
SPI_WRITE(FM25LB_WRITE_ENABLE_COMMAND);
SPI_CS_SET(FM25LB_CS_N_PORT_NUM, FM25LB_CS_N_PIN);
SPI_CS_CLR(FM25LB_CS_N_PORT_NUM, FM25LB_CS_N_PIN);
/* Send the WRITE command and the address to the FRAM */
SPI_WRITE(FM25LB_ADD_ADDRESS_BIT(address, FM25LB_WRITE_COMMAND));
SPI_WRITE(address & 0xFF);
/* Send the data to write */
for(i=0; i<len; i++) {
SPI_WRITE(buf[i]);
}
SPI_CS_SET(FM25LB_CS_N_PORT_NUM, FM25LB_CS_N_PIN);
return 0;
}
/**
* \brief Write to the FRAM chip.
* \param address The index of the byte to start writing to.
* \param len The number of bytes to write.
* \param buf A buffer of values to write.
* \return 0 on success, -1 on error
*
* Writes len bytes to the FRAM chip starting at address.
*/
int
fm25v02_write(uint16_t address, uint16_t len, uint8_t *buf)
{
uint16_t i;
spi_set_mode(SSI_CR0_FRF_MOTOROLA, SSI_CR0_SPO, SSI_CR0_SPH, 8);
SPI_CS_CLR(FM25V02_CS_N_PORT_NUM, FM25V02_CS_N_PIN);
/* Send the WRITE ENABLE command to allow writing to the FRAM */
SPI_WRITE(FM25V02_WRITE_ENABLE_COMMAND);
SPI_CS_SET(FM25V02_CS_N_PORT_NUM, FM25V02_CS_N_PIN);
SPI_CS_CLR(FM25V02_CS_N_PORT_NUM, FM25V02_CS_N_PIN);
/* Send the WRITE command and the address to the FRAM */
SPI_WRITE(FM25V02_WRITE_COMMAND);
address &= 0x7fff;
SPI_WRITE((address&0xff00)>>8);
SPI_WRITE((address&0xff));
/* Send the data to write */
for(i=0; i<len; i++) {
SPI_WRITE(buf[i]);
}
SPI_CS_SET(FM25V02_CS_N_PORT_NUM, FM25V02_CS_N_PIN);
return 0;
}
int fm25v02_writeStatus(uint8_t statusReg){
// Set WEL bit in status register
spi_set_mode(SSI_CR0_FRF_MOTOROLA, 0, 0, 8);
SPI_CS_CLR(FM25V02_CS_N_PORT_NUM, FM25V02_CS_N_PIN);
SPI_WRITE(FM25V02_WRITE_ENABLE_COMMAND);
SPI_CS_SET(FM25V02_CS_N_PORT_NUM, FM25V02_CS_N_PIN);
SPI_CS_CLR(FM25V02_CS_N_PORT_NUM, FM25V02_CS_N_PIN);
SPI_WRITE(FM25V02_WRITE_STATUS_COMMAND);
SPI_WRITE(statusReg);
SPI_CS_SET(FM25V02_CS_N_PORT_NUM, FM25V02_CS_N_PIN);
return 0;
}
/**
* \brief Read from the FRAM chip.
* \param address The index of the byte to start reading from.
* \param len The number of bytes to read.
* \param buf A buffer to put the return data in.
* \return 0 on success, -1 on error
*
* Reads len bytes from the FRAM chip starting at address.
*/
int
fm25lb_read(uint16_t address, uint16_t len, uint8_t *buf)
{
uint16_t i;
// uint16_t c;
// uint16_t cycles = (len / 6) + 1;
// uint16_t index = 0;
uint16_t current_address = address;
spi_set_mode(SSI_CR0_FRF_MOTOROLA, SSI_CR0_SPO, SSI_CR0_SPH, 8);
SPI_CS_CLR(FM25LB_CS_N_PORT_NUM, FM25LB_CS_N_PIN);
/* Send the READ command and the address to the FRAM */
SPI_WRITE(FM25LB_ADD_ADDRESS_BIT(current_address, FM25LB_READ_COMMAND));
SPI_WRITE(current_address & 0xFF);
SPI_FLUSH();
for (i=0; i<len; i++) {
SPI_READ(buf[i]);
}
SPI_CS_SET(FM25LB_CS_N_PORT_NUM, FM25LB_CS_N_PIN);
return 0;
}
/**
* \brief Read from the FRAM chip.
* \param address The index of the byte to start reading from.
* \param len The number of bytes to read.
* \param buf A buffer to put the return data in.
* \return 0 on success, -1 on error
*
* Reads len bytes from the FRAM chip starting at address.
*/
int
fm25v02_read(uint16_t address, uint16_t len, uint8_t *buf)
{
uint16_t i;
spi_set_mode(SSI_CR0_FRF_MOTOROLA, SSI_CR0_SPO, SSI_CR0_SPH, 8);
SPI_CS_CLR(FM25V02_CS_N_PORT_NUM, FM25V02_CS_N_PIN);
/* Send the READ command and the address to the FRAM */
SPI_WRITE(FM25V02_READ_COMMAND);
address &= 0x7fff;
SPI_WRITE((address&0xff00)>>8);
SPI_WRITE((address&0xff));
SPI_FLUSH();
for (i=0; i<len; i++) {
SPI_READ(buf[i]);
}
SPI_CS_SET(FM25V02_CS_N_PORT_NUM, FM25V02_CS_N_PIN);
return 0;
}
int
rv3049_set_time(rv3049_time_t* time)
{
uint8_t buf[8];
int i;
buf[0] = rv3049_binary_to_bcd(time->seconds);
buf[1] = rv3049_binary_to_bcd(time->minutes);
buf[2] = rv3049_binary_to_bcd(time->hours); // 24 hour mode
buf[3] = rv3049_binary_to_bcd(time->days);
buf[4] = time->weekday;
buf[5] = time->month;
buf[6] = rv3049_binary_to_bcd(time->year - 2000);
spix_set_mode(SPI_CONF_DEFAULT_INSTANCE, SSI_CR0_FRF_MOTOROLA, 0, SSI_CR0_SPH, 8);
SPI_CS_SET(RV3049_CS_PORT_NUM, RV3049_CS_PIN);
// Signal a write to the clock
SPI_WRITE(RV3049_SET_WRITE_BIT(RV3049_PAGE_ADDR_CLOCK));
// Write the clock values
for (i=0; i<RV3049_WRITE_LEN_TIME; i++) {
SPI_WRITE(buf[i]);
}
SPI_CS_CLR(RV3049_CS_PORT_NUM, RV3049_CS_PIN);
return 0;
}
void nrf51822_interrupt(uint8_t port, uint8_t pin)
{
uint16_t b;
uint8_t buf[256];
int i;
leds_toggle(LEDS_RED);
spi_set_mode(SSI_CR0_FRF_MOTOROLA, 0, 0, 8);
SPI_CS_CLR(NRF51822_CS_N_PORT_NUM, NRF51822_CS_N_PIN);
clock_delay_usec(8);
// READ_IRQ
SPI_WRITE(0x01);
SPI_FLUSH();
SPI_CS_SET(NRF51822_CS_N_PORT_NUM, NRF51822_CS_N_PIN);
clock_delay_usec(75);
SPI_CS_CLR(NRF51822_CS_N_PORT_NUM, NRF51822_CS_N_PIN);
clock_delay_usec(8);
SPI_READ(b);
if (b == 0xFF) {
// ERROR on the nrf51822 side. Skip this.
} else {
for (i=0; i<b; i++) {
SPI_READ(buf[i]);
}
}
SPI_CS_SET(NRF51822_CS_N_PORT_NUM, NRF51822_CS_N_PIN);
}
uint8_t fm25v02_readStatus(){
uint8_t statusReg;
spi_set_mode(SSI_CR0_FRF_MOTOROLA, 0, 0, 8);
SPI_CS_CLR(FM25V02_CS_N_PORT_NUM, FM25V02_CS_N_PIN);
SPI_WRITE(FM25V02_READ_STATUS_COMMAND);
SPI_FLUSH();
SPI_READ(statusReg);
SPI_CS_SET(FM25V02_CS_N_PORT_NUM, FM25V02_CS_N_PIN);
return statusReg;
}
void fm25v02_eraseAll(){
uint16_t i;
spi_set_mode(SSI_CR0_FRF_MOTOROLA, 0, 0, 8);
SPI_CS_CLR(FM25V02_CS_N_PORT_NUM, FM25V02_CS_N_PIN);
SPI_WRITE(FM25V02_WRITE_ENABLE_COMMAND);
SPI_CS_SET(FM25V02_CS_N_PORT_NUM, FM25V02_CS_N_PIN);
SPI_CS_CLR(FM25V02_CS_N_PORT_NUM, FM25V02_CS_N_PIN);
SPI_WRITE(FM25V02_WRITE_COMMAND);
// Address
SPI_WRITE(0x00);
SPI_WRITE(0x00);
/* Send the data to write */
for(i=0; i<0x7fff; i++) {
SPI_WRITE(0x00);
}
SPI_CS_SET(FM25V02_CS_N_PORT_NUM, FM25V02_CS_N_PIN);
}
void fm25v02_dummyWakeup(){
uint8_t dummyReg;
//uint16_t dummyCnt;
spi_set_mode(SSI_CR0_FRF_MOTOROLA, 0, 0, 8);
SPI_CS_CLR(FM25V02_CS_N_PORT_NUM, FM25V02_CS_N_PIN);
// Delay for 400-ish us
clock_delay_usec(400);
//for (dummyCnt=0; dummyCnt<800; dummyCnt++)
// asm("nop");
SPI_FLUSH();
SPI_READ(dummyReg);
SPI_CS_SET(FM25V02_CS_N_PORT_NUM, FM25V02_CS_N_PIN);
}
void nrf51822_get_all_advertisements () {
//spi_set_mode(SSI_CR0_FRF_MOTOROLA, SSI_CR0_SPO, SSI_CR0_SPH, 8);
spi_set_mode(SSI_CR0_FRF_MOTOROLA, 0, 0, 8);
SPI_CS_CLR(NRF51822_CS_N_PORT_NUM, NRF51822_CS_N_PIN);
clock_delay_usec(8);
// GET ADVERTISEMENTS
SPI_WRITE(0x02);
SPI_FLUSH();
SPI_CS_SET(NRF51822_CS_N_PORT_NUM, NRF51822_CS_N_PIN);
}
void
rv3049_init()
{
/* Set the HOLD_N and WP_N pins to outputs and high */
GPIO_SET_INPUT(GPIO_PORT_TO_BASE(RV3049_INT_N_PORT_NUM),
GPIO_PIN_MASK(RV3049_INT_N_PIN));
spix_cs_init(RV3049_CS_PORT_NUM, RV3049_CS_PIN);
SPI_CS_CLR(RV3049_CS_PORT_NUM, RV3049_CS_PIN);
// Write the initial values
{
rv3049_time_t start_time = {RTC_SECONDS, RTC_MINUTES, RTC_HOURS,
RTC_DAYS, RTC_WEEKDAY, RTC_MONTH,
RTC_YEAR};
rv3049_set_time(&start_time);
}
}
int
rv3049_read_time(rv3049_time_t* time)
{
uint8_t buf[8];
int i;
spix_set_mode(SPI_CONF_DEFAULT_INSTANCE, SSI_CR0_FRF_MOTOROLA, 0, SSI_CR0_SPH, 8);
SPI_CS_SET(RV3049_CS_PORT_NUM, RV3049_CS_PIN);
// Tell the RTC we want to read the clock
SPI_WRITE(RV3049_SET_READ_BIT(RV3049_PAGE_ADDR_CLOCK));
SPI_FLUSH();
// Read a null byte here. Not exactly sure why.
SPI_READ(buf[0]);
// Then actually read the clock
for (i=0; i<RV3049_READ_LEN_TIME; i++) {
SPI_READ(buf[i]);
}
SPI_CS_CLR(RV3049_CS_PORT_NUM, RV3049_CS_PIN);
// Convert the values
time->seconds = BCD_TO_BINARY(buf[0]);
time->minutes = BCD_TO_BINARY(buf[1]);
time->hours = BCD_TO_BINARY((buf[2])&0x3F);
time->days = BCD_TO_BINARY(buf[3]);
time->weekday = buf[4];
time->month = buf[5];
time->year = BCD_TO_BINARY(buf[6])+2000;
return 0;
}
/*---------------------------------------------------------------------------*/
void
enc28j60_arch_spi_select(void)
{
SPI_CS_CLR(SPI_CS_PORT, SPI_CS_PIN);
}
void fm25v02_sleep(){
spi_set_mode(SSI_CR0_FRF_MOTOROLA, 0, 0, 8);
SPI_CS_CLR(FM25V02_CS_N_PORT_NUM, FM25V02_CS_N_PIN);
SPI_WRITE(FM25V02_SLEEP_COMMAND);
SPI_CS_SET(FM25V02_CS_N_PORT_NUM, FM25V02_CS_N_PIN);
}
