/*FUNCTION**********************************************************************
*
* Function Name : SPI_DRV_DmaSlaveStartTransfer
* Description : Starts the transfer with information passed.
*
*END**************************************************************************/
static spi_status_t SPI_DRV_DmaSlaveStartTransfer(uint32_t instance)
{
spi_dma_slave_state_t * spiState = (spi_dma_slave_state_t *)g_spiStatePtr[instance];
/* For temporarily storing DMA register channel */
void * param;
SPI_Type *base = g_spiBase[instance];
uint32_t transferSizeInBytes; /* DMA transfer size in bytes */
/* Initialize s_byteToSend */
s_byteToSend = spiState->dummyPattern;
/* If the transfer count is zero, then return immediately. */
if (spiState->remainingSendByteCount == 0)
{
/* Signal the synchronous completion object if the transfer wasn't async.
* Otherwise, when we return the the sync function we'll get stuck in the sync wait loop.
*/
if (spiState->isSync)
{
/* Signal the synchronous completion object */
OSA_EventSet(&spiState->event, kSpiDmaTransferDone);
}
return kStatus_SPI_Success;
}
/* In order to flush any remaining data in the shift register, disable then enable the SPI */
SPI_HAL_Disable(base);
SPI_HAL_Enable(base);
/* First, set the DMA transfer size in bytes */
#if FSL_FEATURE_SPI_16BIT_TRANSFERS
if (SPI_HAL_Get8or16BitMode(base) == kSpi16BitMode)
{
transferSizeInBytes = 2;
/* If bits/frame > 8, meaning 2 bytes, then the transfer byte count must not be an odd
* count. If so, drop the last odd byte. This odd byte will be transferred in when dma
* completed
*/
if (spiState->remainingSendByteCount % 2 != 0)
{
spiState->remainingSendByteCount ++;
spiState->remainingReceiveByteCount --;
spiState->hasExtraByte = true;
}
else
{
spiState->hasExtraByte = false;
}
}
else
{
transferSizeInBytes = 1;
}
#else
transferSizeInBytes = 1;
#endif /* FSL_FEATURE_SPI_16BIT_TRANSFERS */
param = (void *)(instance); /* For DMA callback, set "param" as the SPI instance number */
/* Save information about the transfer for use by the ISR. */
spiState->isTransferInProgress = true;
/************************************************************************************
* Set up the RX DMA channel Transfer Control Descriptor (TCD)
* Note, if there is no receive buffer (if user passes in NULL), then bypass RX DMA
* set up.
************************************************************************************/
/* If no receive buffer then disable incrementing the destination and set the destination
* to a temporary location
*/
if ((spiState->remainingReceiveByteCount > 0) || (spiState->hasExtraByte))
{
uint32_t receiveSize = spiState->remainingReceiveByteCount;
if ((!spiState->receiveBuffer) || (!spiState->remainingReceiveByteCount))
{
if (!spiState->remainingReceiveByteCount)
{
/* If receive count is 0, always receive 1 frame (2 bytes) */
receiveSize = 2;
}
/* Set up this channel's control which includes enabling the DMA interrupt */
DMA_DRV_ConfigTransfer(&spiState->dmaReceive,
kDmaPeripheralToPeripheral,
transferSizeInBytes,
SPI_HAL_GetDataRegAddr(base), /* src is data register */
(uint32_t)(&s_rxBuffIfNull), /* dest is temporary location */
(uint32_t)(receiveSize));
}
else
{
/* Set up this channel's control which includes enabling the DMA interrupt */
DMA_DRV_ConfigTransfer(&spiState->dmaReceive,
kDmaPeripheralToMemory,
transferSizeInBytes,
SPI_HAL_GetDataRegAddr(base), /* src is data register */
(uint32_t)(spiState->receiveBuffer), /* dest is rx buffer */
(uint32_t)(receiveSize));
}
/* Destination size is only one byte */
DMA_DRV_SetDestTransferSize(&spiState->dmaReceive, 1U);
/* Enable the DMA peripheral request */
DMA_DRV_StartChannel(&spiState->dmaReceive);
/* Register callback for DMA interrupt */
DMA_DRV_RegisterCallback(&spiState->dmaReceive, SPI_DRV_DmaSlaveCallback, param);
}
/************************************************************************************
* Set up the TX DMA channel Transfer Control Descriptor (TCD)
* Note, if there is no source buffer (if user passes in NULL), then send zeros
************************************************************************************/
/* Per the reference manual, before enabling the SPI transmit DMA request, we first need
* to read the status register and then write to the SPI data register. Afterwards, we need
* to decrement the sendByteCount and perform other driver maintenance functions.
*/
/* Read the SPI Status register */
SPI_HAL_IsTxBuffEmptyPending(base);
/* Start the transfer by writing the first byte/word to the SPI data register.
* If a send buffer was provided, the byte/word comes from there. Otherwise we just send zeros.
*/
#if FSL_FEATURE_SPI_16BIT_TRANSFERS
if (transferSizeInBytes == 2) /* 16-bit transfers for SPI16 module */
{
if (spiState->sendBuffer)
{
s_byteToSend = *(spiState->sendBuffer);
SPI_HAL_WriteDataLow(base, s_byteToSend);
++spiState->sendBuffer;
s_byteToSend = *(spiState->sendBuffer);
SPI_HAL_WriteDataHigh(base, s_byteToSend);
++spiState->sendBuffer;
}
else /* Else, if no send buffer, write zeros */
{
SPI_HAL_WriteDataLow(base, s_byteToSend);
SPI_HAL_WriteDataHigh(base, s_byteToSend);
}
spiState->remainingSendByteCount -= 2; /* Decrement the send byte count by 2 */
}
else /* 8-bit transfers for SPI16 module */
{
if (spiState->sendBuffer)
{
s_byteToSend = *(spiState->sendBuffer);
++spiState->sendBuffer;
}
SPI_HAL_WriteDataLow(base, s_byteToSend); /* If no send buffer, s_byteToSend=0 */
--spiState->remainingSendByteCount; /* Decrement the send byte count for use in DMA setup */
}
#else
/* For SPI modules that do not support 16-bit transfers */
if (spiState->sendBuffer)
{
s_byteToSend = *(spiState->sendBuffer);
++spiState->sendBuffer;
}
SPI_HAL_WriteData(base, s_byteToSend); /* If no send buffer, s_byteToSend=0 */
--spiState->remainingSendByteCount; /* Decrement the send byte count for use in DMA setup */
#endif /* FSL_FEATURE_SPI_16BIT_TRANSFERS */
/* If there are no more bytes to send then return without setting up the TX DMA channel.
* Else, set up the TX DMA channel and enable the TX DMA request.
*/
if (!spiState->remainingSendByteCount) /* No more bytes to send */
{
if ((spiState->remainingReceiveByteCount) || (spiState->hasExtraByte))
{
/* Enable the RX DMA channel request now */
SPI_HAL_SetRxDmaCmd(base, true);
return kStatus_SPI_Success;
}
else /* If RX DMA chan not setup then enable the interrupt to get the received byte */
{
SPI_HAL_SetIntMode(base, kSpiTxEmptyInt, true);
return kStatus_SPI_Success;
}
}
else /* Since there are more bytes to send, set up the TX DMA channel */
{
/* If there is a send buffer, data comes from there, else send 0 */
if (spiState->sendBuffer)
{
/* Set up this channel's control which includes enabling the DMA interrupt */
DMA_DRV_ConfigTransfer(&spiState->dmaTransmit, kDmaMemoryToPeripheral,
transferSizeInBytes,
(uint32_t)(spiState->sendBuffer),
SPI_HAL_GetDataRegAddr(base),
(uint32_t)(spiState->remainingSendByteCount));
}
else /* Configure TX DMA channel to send zeros */
{
/* Set up this channel's control which includes enabling the DMA interrupt */
DMA_DRV_ConfigTransfer(&spiState->dmaTransmit, kDmaPeripheralToPeripheral,
transferSizeInBytes,
(uint32_t)(&s_byteToSend),
SPI_HAL_GetDataRegAddr(base),
(uint32_t)(spiState->remainingSendByteCount));
}
/* Source size is only one byte */
DMA_DRV_SetSourceTransferSize(&spiState->dmaTransmit, 1U);
/* Enable the SPI TX DMA Request */
SPI_HAL_SetTxDmaCmd(base, true);
/* Enable the SPI RX DMA request also. */
SPI_HAL_SetRxDmaCmd(base, true);
/* Enable the DMA peripheral request */
DMA_DRV_StartChannel(&spiState->dmaTransmit);
}
return kStatus_SPI_Success;
}
/*!
* @brief Initiate (start) a transfer using DMA. This is not a public API as it is called from
* other driver functions
*/
spi_status_t SPI_DRV_DmaMasterStartTransfer(uint32_t instance,
const spi_dma_master_user_config_t * device)
{
/* instantiate local variable of type spi_dma_master_state_t and point to global state */
spi_dma_master_state_t * spiDmaState = (spi_dma_master_state_t *)g_spiStatePtr[instance];
/* For temporarily storing DMA register channel */
void * param;
uint32_t calculatedBaudRate;
SPI_Type *base = g_spiBase[instance];
uint32_t transferSizeInBytes; /* DMA transfer size in bytes */
/* Initialize s_byteToSend */
s_byteToSend = 0;
/* If the transfer count is zero, then return immediately.*/
if (spiDmaState->remainingSendByteCount == 0)
{
/* Signal the synchronous completion object if the transfer wasn't async.
* Otherwise, when we return the the sync function we'll get stuck in the sync wait loop.
*/
if (spiDmaState->isTransferBlocking)
{
OSA_SemaPost(&spiDmaState->irqSync);
}
return kStatus_SPI_Success;
}
/* Configure bus for this device. If NULL is passed, we assume the caller has
* preconfigured the bus using SPI_DRV_DmaMasterConfigureBus().
* Do nothing for calculatedBaudRate. If the user wants to know the calculatedBaudRate
* then they can call this function separately.
*/
if (device)
{
SPI_DRV_DmaMasterConfigureBus(instance, device, &calculatedBaudRate);
}
/* In order to flush any remaining data in the shift register, disable then enable the SPI */
SPI_HAL_Disable(base);
SPI_HAL_Enable(base);
#if FSL_FEATURE_SPI_16BIT_TRANSFERS
/* Check the transfer byte count. If bits/frame > 8, meaning 2 bytes, and if
* the transfer byte count is an odd count we'll have to round down the RX transfer byte count
* to the next lowest even number by one and assert a flag to indicate in the interrupt handler
* that we take care of sending and receiving this last byte. We'll round up TX byte count.
*/
if (SPI_HAL_Get8or16BitMode(base) == kSpi16BitMode) /* Applies to 16-bit transfers */
{
/* Odd byte count for 16-bit transfers, set the extraByte flag */
if (spiDmaState->remainingSendByteCount & 1UL) /* If odd byte count */
{
transferSizeInBytes = 2; /* Set transfer size to two bytes for the DMA operation */
spiDmaState->extraByte = true; /* Set the extraByte flag */
/* Round up TX byte count so when DMA completes, all data would've been sent */
spiDmaState->remainingSendByteCount += 1U;
/* Round down RX byte count which means at the end of the RX DMA transfer, we'll need
* to set up an interrupt to get the last byte.
*/
spiDmaState->remainingReceiveByteCount &= ~1U;
/* Store the transfer byte count to the run-time state struct
* for later use in the interrupt handler.
*/
spiDmaState->transferByteCnt = spiDmaState->remainingSendByteCount;
}
/* Even byte count for 16-bit transfers, clear the extraByte flag */
else
{
transferSizeInBytes = 2; /* Set transfer size to two bytes for the DMA operation */
spiDmaState->extraByte = false; /* Clear the extraByte flag */
}
}
else /* For 8-bit transfers */
{
transferSizeInBytes = 1;
spiDmaState->extraByte = false;
}
#else
transferSizeInBytes = 1;
#endif
param = (void *)(instance); /* For DMA callback, set "param" as the SPI instance number */
/* Check that we're not busy.*/
if (spiDmaState->isTransferInProgress)
{
return kStatus_SPI_Busy;
}
/* Save information about the transfer for use by the ISR.*/
spiDmaState->isTransferInProgress = true;
/************************************************************************************
* Set up the RX DMA channel Transfer Control Descriptor (TCD)
* Note, if there is no receive byte count, then bypass RX DMA set up.
***********************************************************************************/
if (spiDmaState->remainingReceiveByteCount)
{
/* If no receive buffer then disable incrementing the destination and set the destination
* to a temporary location
*/
if (!spiDmaState->receiveBuffer)
{
/* Set up this channel's control which includes enabling the DMA interrupt */
DMA_DRV_ConfigTransfer(&spiDmaState->dmaReceive,
kDmaPeripheralToPeripheral,
transferSizeInBytes,
SPI_HAL_GetDataRegAddr(base), /* src is data register */
(uint32_t)(&s_rxBuffIfNull), /* dest is temporary location */
(uint32_t)(spiDmaState->remainingReceiveByteCount));
}
else
{
/* Set up this channel's control which includes enabling the DMA interrupt */
DMA_DRV_ConfigTransfer(&spiDmaState->dmaReceive,
kDmaPeripheralToMemory,
transferSizeInBytes,
SPI_HAL_GetDataRegAddr(base), /* src is data register */
(uint32_t)(spiDmaState->receiveBuffer),/* dest is rx buffer */
(uint32_t)(spiDmaState->remainingReceiveByteCount));
}
/* Dest size is always 1 byte on each transfer */
DMA_DRV_SetDestTransferSize(&spiDmaState->dmaReceive, 1U);
/* Enable the DMA peripheral request */
DMA_DRV_StartChannel(&spiDmaState->dmaReceive);
/* Register callback for DMA interrupt */
DMA_DRV_RegisterCallback(&spiDmaState->dmaReceive, SPI_DRV_DmaMasterCallback, param);
}
/************************************************************************************
* Set up the TX DMA channel Transfer Control Descriptor (TCD)
* Note, if there is no source buffer (if user passes in NULL), then send zeros
***********************************************************************************/
/* Per the reference manual, before enabling the SPI transmit DMA request, we first need
* to read the status register and then write to the SPI data register. Afterwards, we need
* to decrement the sendByteCount and perform other driver maintenance functions.
*/
/* Read the SPI Status register */
SPI_HAL_IsTxBuffEmptyPending(base);
/* Start the transfer by writing the first byte/word to the SPI data register.
* If a send buffer was provided, the byte/word comes from there. Otherwise we just send zeros.
* This will cause an immeidate transfer which in some cases may cause the RX DMA channel to
* complete before having the chance to completely set up the TX DMA channel. As such, we'll
* enable the RX DMA channel last.
*/
#if FSL_FEATURE_SPI_16BIT_TRANSFERS
if (transferSizeInBytes == 2) /* 16-bit transfers for SPI16 module */
{
if (spiDmaState->sendBuffer)
{
s_byteToSend = *(spiDmaState->sendBuffer);
SPI_HAL_WriteDataLow(base, s_byteToSend);
++spiDmaState->sendBuffer;
s_byteToSend = *(spiDmaState->sendBuffer);
SPI_HAL_WriteDataHigh(base, s_byteToSend);
++spiDmaState->sendBuffer;
}
else /* Else, if no send buffer, write zeros */
{
SPI_HAL_WriteDataLow(base, s_byteToSend);
SPI_HAL_WriteDataHigh(base, s_byteToSend);
}
spiDmaState->remainingSendByteCount -= 2; /* Decrement the send byte count by 2 */
}
else /* 8-bit transfers for SPI16 module */
{
if (spiDmaState->sendBuffer)
{
s_byteToSend = *(spiDmaState->sendBuffer);
++spiDmaState->sendBuffer;
}
SPI_HAL_WriteDataLow(base, s_byteToSend); /* If no send buffer, s_byteToSend=0 */
--spiDmaState->remainingSendByteCount; /* Decrement the send byte count */
}
#else
/* For SPI modules that do not support 16-bit transfers */
if (spiDmaState->sendBuffer)
{
s_byteToSend = *(spiDmaState->sendBuffer);
++spiDmaState->sendBuffer;
}
SPI_HAL_WriteData(base, s_byteToSend); /* If no send buffer, s_byteToSend=0 */
--spiDmaState->remainingSendByteCount; /* Decrement the send byte count */
#endif
/* If there are no more bytes to send then return without setting up the TX DMA channel
* and let the receive DMA channel complete the transfer if the RX DMA channel was setup.
* If the RX DMA channel was not set up (due to odd byte count of 1 in 16-bit mode), enable
* the interrupt to get the received byte.
*/
if (!spiDmaState->remainingSendByteCount) /* No more bytes to send */
{
if (spiDmaState->remainingReceiveByteCount)
{
/* Enable the RX DMA channel request now */
SPI_HAL_SetRxDmaCmd(base, true);
return kStatus_SPI_Success;
}
else /* If RX DMA chan not setup then enable the interrupt to get the received byte */
{
SPI_HAL_SetIntMode(base, kSpiTxEmptyInt, true);
return kStatus_SPI_Success;
}
}
/* Else, since there are more bytes to send, go ahead and set up the TX DMA channel */
else
{
/* If there is a send buffer, data comes from there, else send 0 */
if (spiDmaState->sendBuffer)
{
/* Set up this channel's control which includes enabling the DMA interrupt */
DMA_DRV_ConfigTransfer(&spiDmaState->dmaTransmit, kDmaMemoryToPeripheral,
transferSizeInBytes,
(uint32_t)(spiDmaState->sendBuffer),
SPI_HAL_GetDataRegAddr(base),
(uint32_t)(spiDmaState->remainingSendByteCount));
}
else /* Configure TX DMA channel to send zeros */
{
/* Set up this channel's control which includes enabling the DMA interrupt */
DMA_DRV_ConfigTransfer(&spiDmaState->dmaTransmit, kDmaPeripheralToPeripheral,
transferSizeInBytes,
(uint32_t)(&s_byteToSend),
SPI_HAL_GetDataRegAddr(base),
(uint32_t)(spiDmaState->remainingSendByteCount));
}
/* Source size is only one byte on each transfer */
DMA_DRV_SetSourceTransferSize(&spiDmaState->dmaTransmit, 1U);
/* Enable the SPI TX DMA Request */
SPI_HAL_SetTxDmaCmd(base, true);
/* Enable the SPI RX DMA Request after the TX DMA request is enabled. This is done to
* make sure that the RX DMA channel does not end prematurely before we've completely set
* up the TX DMA channel since part of the TX DMA set up involves placing 1 or 2 bytes of
* data into the send data register which causes an immediate transfer.
*/
SPI_HAL_SetRxDmaCmd(base, true);
/* Enable the DMA peripheral request */
DMA_DRV_StartChannel(&spiDmaState->dmaTransmit);
}
return kStatus_SPI_Success;
}
/*!
* @brief Fill up the TX FIFO with data.
* This function fills up the TX FIFO.
* This is not a public API as it is called from other driver functions.
*/
static void SPI_DRV_MasterFillupTxFifo(uint32_t instance)
{
/* instantiate local variable of type spi_master_state_t and point to global state */
spi_master_state_t * spiState = (spi_master_state_t *)g_spiStatePtr[instance];
SPI_Type *base = g_spiBase[instance];
uint8_t byteToSendLow = 0;
uint8_t byteToSendHigh = 0;
/* Declare variables for storing volatile data later in the code */
uint32_t remainRxByteCnt, remainTxByteCnt;
spi_data_bitcount_mode_t bitCount = SPI_HAL_Get8or16BitMode(base);
/* Store the SPI state struct volatile member variables into temporary
* non-volatile variables to allow for MISRA compliant calculations
*/
remainTxByteCnt = spiState->remainingSendByteCount;
remainRxByteCnt = spiState->remainingReceiveByteCount;
/* Architectural note: When developing the TX FIFO fill functionality, it was found that to
* achieve more efficient run-time performance, it was better to first check the bits/frame
* setting and then proceed with the FIFO fill management process, rather than to clutter the
* FIFO fill process with continual checks of the bits/frame setting.
*/
/* If bits/frame is greater than one byte */
if (bitCount == kSpi16BitMode)
{
/* Fill the fifo until it is full or until the send word count is 0 or until the difference
* between the remainingReceiveByteCount and remainingSendByteCount equals the FIFO depth.
* The reason for checking the difference is to ensure we only send as much as the
* RX FIFO can receive. Note, the FIFO depth assumes maximum data length of 16-bits,
* but since we are using 8-bit buffers, the FIFO depth is twice the reported depth.
*/
while((SPI_HAL_GetFifoStatusFlag(base, kSpiTxFifoFull)== 0) &&
((remainRxByteCnt - remainTxByteCnt) < (g_spiFifoSize[instance]*2)))
{
if (spiState->sendBuffer)
{
byteToSendLow = *(spiState->sendBuffer);
++spiState->sendBuffer;
byteToSendHigh = *(spiState->sendBuffer);
++spiState->sendBuffer;
}
SPI_HAL_WriteDataLow(base, byteToSendLow);
SPI_HAL_WriteDataHigh(base, byteToSendHigh);
spiState->remainingSendByteCount -= 2; /* decrement by 2 */
spiState->transferredByteCount += 2; /* increment by 2 */
/* Update the SPI state struct volatile member variables into temporary
* non-volatile variables to allow for MISRA compliant calculations
*/
remainTxByteCnt = spiState->remainingSendByteCount;
remainRxByteCnt = spiState->remainingReceiveByteCount;
/* exit loop if send count is zero */
if (spiState->remainingSendByteCount == 0)
{
break;
}
}
}
/* Optimized for bit count = 8 */
else
{
/* Fill the fifo until it is full or until the send word count is 0 or until the difference
* between the remainingReceiveByteCount and remainingSendByteCount equals the FIFO depth.
* The reason for checking the difference is to ensure we only send as much as the
* RX FIFO can receive. Note, the FIFO depth assumes maximum data length of 16-bits,
* but since we are using 8-bit buffers, the FIFO depth is twice the reported depth.
*/
while((SPI_HAL_GetFifoStatusFlag(base, kSpiTxFifoFull)== 0) &&
((remainRxByteCnt - remainTxByteCnt) < (g_spiFifoSize[instance]*2)))
{
if (spiState->sendBuffer)
{
byteToSendLow = *(spiState->sendBuffer);
++spiState->sendBuffer;
}
SPI_HAL_WriteDataLow(base, byteToSendLow);
--spiState->remainingSendByteCount;
++spiState->transferredByteCount;
/* Update the SPI state struct volatile member variables into temporary
* non-volatile variables to allow for MISRA compliant calculations
*/
remainTxByteCnt = spiState->remainingSendByteCount;
remainRxByteCnt = spiState->remainingReceiveByteCount;
/* exit loop if send count is zero */
if (spiState->remainingSendByteCount == 0)
{
break;
}
}
}
}
/*FUNCTION**********************************************************************
*
* Function Name : SPI_DRV_MasterIRQHandler
* Description : Interrupt handler for SPI master mode.
* This handler uses the buffers stored in the spi_master_state_t structs to transfer data.
*
*END**************************************************************************/
void SPI_DRV_MasterIRQHandler(uint32_t instance)
{
/* instantiate local variable of type spi_master_state_t and point to global state */
spi_master_state_t * spiState = (spi_master_state_t *)g_spiStatePtr[instance];
SPI_Type *base = g_spiBase[instance];
/* Exit the ISR if no transfer is happening for this instance.*/
if (!spiState->isTransferInProgress)
{
return;
}
/* RECEIVE IRQ handler: Check read buffer only if there are remaining bytes to read. */
if (spiState->remainingReceiveByteCount)
{
#if FSL_FEATURE_SPI_16BIT_TRANSFERS
uint8_t byteReceivedLow, byteReceivedHigh;
spi_data_bitcount_mode_t bitCntRx = SPI_HAL_Get8or16BitMode(base);
/* If the SPI module contains a FIFO (and if it's enabled), drain the FIFO until it is empty
* or until the remainingSendByteCount reaches 0.
*/
if ((g_spiFifoSize[instance] != 0) && (SPI_HAL_GetFifoCmd(base)))
{
/* Clear the RX near full interrupt */
SPI_HAL_ClearFifoIntUsingBitWrite(base, kSpiRxNearFullClearInt);
/* Architectural note: When developing the RX FIFO drain code, it was found that to
* achieve more efficient run-time performance, it was better to first check the
* bits/frame setting and then proceed with the FIFO fill management process, rather
* than to clutter the drain process with continual checks of the bits/frame setting.
*/
/* Optimized for bit count = 16 with FIFO support */
if (bitCntRx == kSpi16BitMode)
{
/* Do this while the RX FIFO is not empty */
while (SPI_HAL_GetFifoStatusFlag(base, kSpiRxFifoEmpty) == 0)
{
/* Read the bytes from the RX FIFO */
byteReceivedLow = SPI_HAL_ReadDataLow(base);
byteReceivedHigh = SPI_HAL_ReadDataHigh(base);
/* Store read bytes into rx buffer only if a buffer pointer was provided */
if (spiState->receiveBuffer)
{
*spiState->receiveBuffer = byteReceivedLow;
++spiState->receiveBuffer;
/* If the extraByte flag is set and these are the last 2 bytes, then skip.
* This will avoid over-writing the rx buffer with another un-needed byte.
*/
if (!((spiState->extraByte) && (spiState->remainingReceiveByteCount == 2)))
{
*spiState->receiveBuffer = byteReceivedHigh;
++spiState->receiveBuffer;
}
}
spiState->remainingReceiveByteCount -= 2; /* decrement the rx byte count by 2 */
/* If there is no more data to receive, break */
if (spiState->remainingReceiveByteCount == 0)
{
break;
}
}
}
/* Optimized for bit count = 8 with FIFO support */
else
{
while (SPI_HAL_GetFifoStatusFlag(base, kSpiRxFifoEmpty) == 0)
{
/* Read the bytes from the RX FIFO */
byteReceivedLow = SPI_HAL_ReadDataLow(base);
/* Store read bytes into rx buffer only if a buffer pointer was provided */
if (spiState->receiveBuffer)
{
*spiState->receiveBuffer = byteReceivedLow;
++spiState->receiveBuffer;
}
--spiState->remainingReceiveByteCount; /* decrement the rx byte count by 1 */
/* If there is no more data to receive, break */
if (spiState->remainingReceiveByteCount == 0)
{
break;
}
}
}
/* If the remaining RX byte count is less than the RX FIFO watermark, enable
* the TX FIFO empty interrupt. Once the TX FIFO is empty, we are ensured
* that the transmission is complete and can then drain the RX FIFO.
*/
if (spiState->remainingReceiveByteCount < g_spiFifoSize[instance])
{
SPI_HAL_SetIntMode(base, kSpiTxEmptyInt, true); /* TX FIFO empty interrupt */
}
}
/* For SPI modules that do not have a FIFO (or if disabled), but have 16-bit transfer
* capability */
else
{
if (SPI_HAL_IsReadBuffFullPending(base))
{
/* For 16-bit transfers w/o FIFO support */
if (bitCntRx == kSpi16BitMode)
{
/* Read the bytes from the RX FIFO */
byteReceivedLow = SPI_HAL_ReadDataLow(base);
byteReceivedHigh = SPI_HAL_ReadDataHigh(base);
/* Store read bytes into rx buffer only if a buffer pointer was provided */
if (spiState->receiveBuffer)
{
*spiState->receiveBuffer = byteReceivedLow;
++spiState->receiveBuffer;
/* If the extraByte flag is set and these are the last 2 bytes, then skip.
* This will avoid over-writing the rx buffer with another un-needed byte.
*/
if (!((spiState->extraByte) && (spiState->remainingReceiveByteCount == 2)))
{
*spiState->receiveBuffer = byteReceivedHigh;
++spiState->receiveBuffer;
}
}
spiState->remainingReceiveByteCount -= 2; /* decrement the rx byte count by 2 */
}
/* For 8-bit transfers w/o FIFO support */
else
{
/* Read the bytes from the RX FIFO */
byteReceivedLow = SPI_HAL_ReadDataLow(base);
/* Store read bytes into rx buffer only if a buffer pointer was provided */
if (spiState->receiveBuffer)
{
*spiState->receiveBuffer = byteReceivedLow;
++spiState->receiveBuffer;
}
--spiState->remainingReceiveByteCount; /* decrement the rx byte count by 1 */
}
}
}
#else /* For SPI modules that do not support 16-bit transfers and don't have FIFO */
uint8_t byteReceived;
/* For SPI modules without 16-bit transfer capability or FIFO support */
if (SPI_HAL_IsReadBuffFullPending(base))
{
/* Read the bytes from the RX FIFO */
byteReceived = SPI_HAL_ReadData(base);
/* Store read bytes into rx buffer only if a buffer pointer was provided */
if (spiState->receiveBuffer)
{
*spiState->receiveBuffer = byteReceived;
++spiState->receiveBuffer;
}
--spiState->remainingReceiveByteCount; /* decrement the rx byte count by 1 */
}
#endif /* FSL_FEATURE_SPI_16BIT_TRANSFERS */
}
/* TRANSMIT IRQ handler
* Check write buffer. We always have to send a byte in order to keep the transfer
* moving. So if the caller didn't provide a send buffer, we just send a zero byte.
*/
uint8_t byteToSend = 0;
if (spiState->remainingSendByteCount)
{
#if FSL_FEATURE_SPI_16BIT_TRANSFERS
uint8_t byteToSendLow = 0;
uint8_t byteToSendHigh = 0;
spi_data_bitcount_mode_t bitCntTx = SPI_HAL_Get8or16BitMode(base);
/* If SPI module has a FIFO and if it is enabled */
if ((g_spiFifoSize[instance] != 0) && (SPI_HAL_GetFifoCmd(base)))
{
if (SPI_HAL_GetFifoStatusFlag(base, kSpiTxNearEmpty))
{
/* Fill of the TX FIFO with ongoing data */
SPI_DRV_MasterFillupTxFifo(instance);
}
}
else
{
if (SPI_HAL_IsTxBuffEmptyPending(base))
{
if (bitCntTx == kSpi16BitMode)
{
if (spiState->sendBuffer)
{
byteToSendLow = *(spiState->sendBuffer);
++spiState->sendBuffer;
byteToSendHigh = *(spiState->sendBuffer);
++spiState->sendBuffer;
}
SPI_HAL_WriteDataLow(base, byteToSendLow);
SPI_HAL_WriteDataHigh(base, byteToSendHigh);
spiState->remainingSendByteCount -= 2; /* decrement by 2 */
spiState->transferredByteCount += 2; /* increment by 2 */
}
else /* SPI configured for 8-bit transfers */
{
if (spiState->sendBuffer)
{
byteToSend = *(spiState->sendBuffer);
++spiState->sendBuffer;
}
SPI_HAL_WriteDataLow(base, byteToSend);
--spiState->remainingSendByteCount;
++spiState->transferredByteCount;
}
}
}
#else /* For SPI modules that do not support 16-bit transfers */
if (SPI_HAL_IsTxBuffEmptyPending(base))
{
if (spiState->sendBuffer)
{
byteToSend = *(spiState->sendBuffer);
++spiState->sendBuffer;
}
SPI_HAL_WriteData(base, byteToSend);
--spiState->remainingSendByteCount;
++spiState->transferredByteCount;
}
#endif /* FSL_FEATURE_SPI_16BIT_TRANSFERS */
}
/* Check if we're done with this transfer. The transfer is complete when all of the
* expected data is received.
*/
if ((spiState->remainingSendByteCount == 0) && (spiState->remainingReceiveByteCount == 0))
{
/* Complete the transfer. This disables the interrupts, so we don't wind up in
* the ISR again.
*/
SPI_DRV_MasterCompleteTransfer(instance);
}
}
/*!
* @brief Initiate (start) a transfer. This is not a public API as it is called from other
* driver functions
*/
static spi_status_t SPI_DRV_MasterStartTransfer(uint32_t instance,
const spi_master_user_config_t * device)
{
/* instantiate local variable of type spi_master_state_t and point to global state */
spi_master_state_t * spiState = (spi_master_state_t *)g_spiStatePtr[instance];
uint32_t calculatedBaudRate;
SPI_Type *base = g_spiBase[instance];
/* Check that we're not busy.*/
if (spiState->isTransferInProgress)
{
return kStatus_SPI_Busy;
}
/* Configure bus for this device. If NULL is passed, we assume the caller has
* preconfigured the bus using SPI_DRV_MasterConfigureBus().
* Do nothing for calculatedBaudRate. If the user wants to know the calculatedBaudRate
* then they can call this function separately.
*/
if (device)
{
SPI_DRV_MasterConfigureBus(instance, device, &calculatedBaudRate);
}
/* In order to flush any remaining data in the shift register, disable then enable the SPI */
SPI_HAL_Disable(base);
SPI_HAL_Enable(base);
#if FSL_FEATURE_SPI_16BIT_TRANSFERS
spi_data_bitcount_mode_t bitCount;
bitCount = SPI_HAL_Get8or16BitMode(base);
/* Check the transfer byte count. If bits/frame > 8, meaning 2 bytes if bits/frame > 8, and if
* the transfer byte count is an odd count we'll have to increase the transfer byte count
* by one and assert a flag to indicate to the receive function that it will need to handle
* an extra byte so that it does not inadverently over-write an another byte to the receive
* buffer. For sending the extra byte, we don't care if we read past the send buffer since we
* are only reading from it and the absolute last byte (that completes the final 16-bit word)
* is a don't care byte anyway.
*/
if ((bitCount == kSpi16BitMode) && (spiState->remainingSendByteCount & 1UL))
{
spiState->remainingSendByteCount += 1;
spiState->remainingReceiveByteCount += 1;
spiState->extraByte = true;
}
else
{
spiState->extraByte = false;
}
#endif
/* If the byte count is zero, then return immediately.*/
if (spiState->remainingSendByteCount == 0)
{
SPI_DRV_MasterCompleteTransfer(instance);
return kStatus_SPI_Success;
}
/* Save information about the transfer for use by the ISR.*/
spiState->isTransferInProgress = true;
spiState->transferredByteCount = 0;
/* Make sure TX data register (or FIFO) is empty. If not, return appropriate
* error status. This also causes a read of the status
* register which is required before writing to the data register below.
*/
if (SPI_HAL_IsTxBuffEmptyPending(base) != 1)
{
return kStatus_SPI_TxBufferNotEmpty;
}
#if FSL_FEATURE_SPI_16BIT_TRANSFERS
/* If the module/instance contains a FIFO (and if enabled), proceed with FIFO usage for either
* 8- or 16-bit transfers, else bypass to non-FIFO usage.
*/
if ((g_spiFifoSize[instance] != 0) && (SPI_HAL_GetFifoCmd(base)))
{
/* First fill the FIFO with data */
SPI_DRV_MasterFillupTxFifo(instance);
/* If the remaining RX byte count is less than the RX FIFO watermark, enable
* the TX FIFO empty interrupt. Once the TX FIFO is empty, we are ensured
* that the transmission is complete and can then drain the RX FIFO.
* Else, enable the RX FIFO interrupt based on the watermark. In the IRQ
* handler, another check will be made to see if the remaining RX byte count
* is less than the RX FIFO watermark.
*/
if (spiState->remainingReceiveByteCount < g_spiFifoSize[instance])
{
SPI_HAL_SetIntMode(base, kSpiTxEmptyInt, true); /* TX FIFO empty interrupt */
}
else
{
SPI_HAL_SetFifoIntCmd(base, kSpiRxFifoNearFullInt, true);
}
}
/* Modules that support 16-bit transfers but without FIFO support */
else
{
uint8_t byteToSend = 0;
/* SPI configured for 16-bit transfers, no FIFO */
if (bitCount == kSpi16BitMode)
{
uint8_t byteToSendLow = 0;
uint8_t byteToSendHigh = 0;
if (spiState->sendBuffer)
{
byteToSendLow = *(spiState->sendBuffer);
++spiState->sendBuffer;
/* If the extraByte flag is set and these are the last 2 bytes, then skip this */
if (!((spiState->extraByte) && (spiState->remainingSendByteCount == 2)))
{
byteToSendHigh = *(spiState->sendBuffer);
++spiState->sendBuffer;
}
}
SPI_HAL_WriteDataLow(base, byteToSendLow);
SPI_HAL_WriteDataHigh(base, byteToSendHigh);
spiState->remainingSendByteCount -= 2; /* decrement by 2 */
spiState->transferredByteCount += 2; /* increment by 2 */
}
/* SPI configured for 8-bit transfers, no FIFO */
else
{
if (spiState->sendBuffer)
{
byteToSend = *(spiState->sendBuffer);
++spiState->sendBuffer;
}
SPI_HAL_WriteDataLow(base, byteToSend);
--spiState->remainingSendByteCount;
++spiState->transferredByteCount;
}
/* Only enable the receive interrupt. This should be ok since SPI is a synchronous
* protocol, so every RX interrupt we get, we should be ready to send. However, since
* the SPI has a shift register and data buffer (for transmit and receive), things may not
* be cycle-to-cycle synchronous. To compensate for this, enabling the RX interrupt only
* ensures that we do indeed receive data before sending out the next data word. In the
* ISR we make sure to first check for the RX data buffer full before checking the TX
* data register empty flag.
*/
SPI_HAL_SetIntMode(base, kSpiRxFullAndModfInt, true);
}
#else /* For SPI modules that do not support 16-bit transfers */
/* Start the transfer by writing the first byte. If a send buffer was provided, the byte
* comes from there. Otherwise we just send a zero byte. Note that before writing to the
* data register, the status register must first be read, which was already performed above.
*/
uint8_t byteToSend = 0;
if (spiState->sendBuffer)
{
byteToSend = *(spiState->sendBuffer);
++spiState->sendBuffer;
}
SPI_HAL_WriteData(base, byteToSend);
--spiState->remainingSendByteCount;
++spiState->transferredByteCount;
/* Only enable the receive interrupt. This should be ok since SPI is a synchronous
* protocol, so every RX interrupt we get, we should be ready to send. However, since
* the SPI has a shift register and data buffer (for transmit and receive), things may not
* be cycle-to-cycle synchronous. To compensate for this, enabling the RX interrupt only
* ensures that we do indeed receive data before sending out the next data word. In the
* ISR we make sure to first check for the RX data buffer full before checking the TX
* data register empty flag.
*/
SPI_HAL_SetIntMode(base, kSpiRxFullAndModfInt, true);
#endif
return kStatus_SPI_Success;
}