/**
* @brief Configures Button GPIO and EXTI Line.
* @param Button: Specifies the Button to be configured.
* This parameter should be: BUTTON_USER
* @param ButtonMode: Specifies Button mode.
* This parameter can be one of following parameters:
* @arg BUTTON_MODE_GPIO: Button will be used as simple IO
* @arg BUTTON_MODE_EXTI: Button will be connected to EXTI line with interrupt
* generation capability
* @retval None
*/
void BSP_PB_Init(Button_TypeDef Button, ButtonMode_TypeDef ButtonMode)
{
GPIO_InitTypeDef GPIO_InitStruct;
/* Enable the BUTTON Clock */
BUTTONx_GPIO_CLK_ENABLE(Button);
__SYSCFG_CLK_ENABLE();
if(ButtonMode == BUTTON_MODE_GPIO)
{
/* Configure Button pin as input */
GPIO_InitStruct.Pin = BUTTON_PIN[Button];
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_PULLDOWN;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
HAL_GPIO_Init(BUTTON_PORT[Button], &GPIO_InitStruct);
}
if(ButtonMode == BUTTON_MODE_EXTI)
{
/* Configure Button pin as input with External interrupt */
GPIO_InitStruct.Pin = BUTTON_PIN[Button];
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Mode = GPIO_MODE_IT_RISING;
HAL_GPIO_Init(BUTTON_PORT[Button], &GPIO_InitStruct);
/* Enable and set Button EXTI Interrupt to the lowest priority */
HAL_NVIC_SetPriority((IRQn_Type)(BUTTON_IRQn[Button]), 0x0F, 0x00);
HAL_NVIC_EnableIRQ((IRQn_Type)(BUTTON_IRQn[Button]));
}
}
/**
* @brief System Clock Configuration
* @param None
* @retval None
*/
void SystemClock_Config(void)
{
RCC_ClkInitTypeDef RCC_ClkInitStruct;
RCC_OscInitTypeDef RCC_OscInitStruct;
__PWR_CLK_ENABLE();
__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
RCC_OscInitStruct.HSIState = RCC_HSI_ON;
RCC_OscInitStruct.HSICalibrationValue = 0x10;
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
RCC_OscInitStruct.PLL.PLLMUL = RCC_PLLMUL_4;
RCC_OscInitStruct.PLL.PLLDIV = RCC_PLLDIV_2;
HAL_RCC_OscConfig(&RCC_OscInitStruct);
RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1);
__SYSCFG_CLK_ENABLE();
}
/** Clock configuration
*/
void clock_init(void)
{
RCC_OscInitTypeDef RCC_OscInitStruct;
RCC_ClkInitTypeDef RCC_ClkInitStruct;
RCC_PeriphCLKInitTypeDef PeriphClkInit;
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
RCC_OscInitStruct.HSIState = RCC_HSI_ON;
RCC_OscInitStruct.HSICalibrationValue = 16;
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL12;
RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV1;
HAL_RCC_OscConfig(&RCC_OscInitStruct);
RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1;
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1);
PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USART1;
PeriphClkInit.Usart1ClockSelection = RCC_USART1CLKSOURCE_PCLK1;
//PeriphClkInit.I2c1ClockSelection = RCC_I2C1CLKSOURCE_HSI;
HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit);
__SYSCFG_CLK_ENABLE();
}
/**
* @brief Main program.
* @param None
* @retval None
*/
int main(void)
{
uint32_t i=0;
/* STM32F0xx HAL library initialization:
- Configure the Flash prefetch
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Low Level Initialization
*/
HAL_Init();
/* Copy the vector table from the Flash (mapped at the base of the application
load address 0x08007000) to the base address of the SRAM at 0x20000000. */
for(i = 0; i < 48; i++)
{
VectorTable[i] = *(__IO uint32_t*)(APPLICATION_ADDRESS + (i<<2));
}
/* Enable the SYSCFG peripheral clock*/
__SYSCFG_CLK_ENABLE();
/* Remap SRAM at 0x00000000 */
__HAL_REMAPMEMORY_SRAM();
/* Initialize LEDs */
BSP_LED_Init(LED1);
BSP_LED_Init(LED2);
BSP_LED_Init(LED3);
BSP_LED_Init(LED4);
/* Configure the system clock to have a system clock = 48 MHz */
SystemClock_Config();
/* Turn on LED1 and LED3 */
BSP_LED_On(LED1);
BSP_LED_On(LED3);
/* Infinite loop */
while (1)
{
/* Toggle LED2 and LED4 */
BSP_LED_Toggle(LED2);
BSP_LED_Toggle(LED4);
/* Insert 50 ms delay */
HAL_Delay(50);
/* Toggle LED1 and LED3 */
BSP_LED_Toggle(LED1);
BSP_LED_Toggle(LED3);
/* Insert 100 ms delay */
HAL_Delay(100);
}
}
void init_CLock()
{
__GPIOA_CLK_ENABLE();
__GPIOB_CLK_ENABLE();
__GPIOC_CLK_ENABLE();
__SYSCFG_CLK_ENABLE();
__ETH_CLK_ENABLE();
__HAL_RCC_ETHMAC_CLK_ENABLE();
}
/**
* Initializes the Global MSP.
*/
void HAL_MspInit(void)
{
__SYSCFG_CLK_ENABLE();
/* System interrupt init*/
/* SysTick_IRQn interrupt configuration */
HAL_NVIC_SetPriority(SysTick_IRQn, 0, 0);
__HAL_REMAP_PIN_ENABLE(HAL_REMAP_PA11_PA12);
}
/**
* @brief Initializes the COMP according to the specified
* parameters in the COMP_InitTypeDef and create the associated handle.
* @note If the selected comparator is locked, initialization can't be performed.
* To unlock the configuration, perform a system reset.
* @param hcomp: COMP handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_COMP_Init(COMP_HandleTypeDef *hcomp)
{
HAL_StatusTypeDef status = HAL_OK;
/* Check the COMP handle allocation and lock status */
if((hcomp == NULL) || ((hcomp->State & COMP_STATE_BIT_LOCK) != RESET))
{
status = HAL_ERROR;
}
else
{
/* Check the parameter */
assert_param(IS_COMP_ALL_INSTANCE(hcomp->Instance));
assert_param(IS_COMP_INVERTINGINPUT(hcomp->Init.InvertingInput));
assert_param(IS_COMP_NONINVERTINGINPUT(hcomp->Init.NonInvertingInput));
assert_param(IS_COMP_NONINVERTINGINPUT_INSTANCE(hcomp->Instance, hcomp->Init.NonInvertingInput));
assert_param(IS_COMP_OUTPUT(hcomp->Init.Output));
assert_param(IS_COMP_OUTPUTPOL(hcomp->Init.OutputPol));
assert_param(IS_COMP_HYSTERESIS(hcomp->Init.Hysteresis));
assert_param(IS_COMP_MODE(hcomp->Init.Mode));
assert_param(IS_COMP_BLANKINGSRCE(hcomp->Init.BlankingSrce));
assert_param(IS_COMP_BLANKINGSRCE_INSTANCE(hcomp->Instance, hcomp->Init.BlankingSrce));
if(hcomp->Init.WindowMode != COMP_WINDOWMODE_DISABLED)
{
assert_param(IS_COMP_WINDOWMODE_INSTANCE(hcomp->Instance));
}
if(hcomp->State == HAL_COMP_STATE_RESET)
{
/* Init SYSCFG and the low level hardware to access comparators */
__SYSCFG_CLK_ENABLE();
HAL_COMP_MspInit(hcomp);
}
/* Set COMP parameters */
/* Set COMPxINSEL bits according to hcomp->Init.InvertingInput value */
/* Set COMPxNONINSEL bits according to hcomp->Init.NonInvertingInput value */
/* Set COMPxBLANKING bits according to hcomp->Init.BlankingSrce value */
/* Set COMPxOUTSEL bits according to hcomp->Init.Output value */
/* Set COMPxPOL bit according to hcomp->Init.OutputPol value */
/* Set COMPxHYST bits according to hcomp->Init.Hysteresis value */
/* Set COMPxMODE bits according to hcomp->Init.Mode value */
COMP_INIT(hcomp);
/* Initialize the COMP state*/
if(hcomp->State == HAL_COMP_STATE_RESET)
{
hcomp->State = HAL_COMP_STATE_READY;
}
}
return status;
}
/**
* @brief Initializes the PCD MSP.
* @param hpcd: PCD handle
* @retval None
*/
void HAL_PCD_MspInit(PCD_HandleTypeDef *hpcd)
{
GPIO_InitTypeDef GPIO_InitStruct;
/* Enable the GPIOA clock for USB DataLines */
__GPIOA_CLK_ENABLE();
/* Enable the GPIOB clock for USB external Pull-Up */
__GPIOB_CLK_ENABLE();
/* Configure USB DM and DP pins */
GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12);
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF14_USB;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
GPIO_InitStruct.Pin = USB_DISCONNECT_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_OD;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
HAL_GPIO_Init(USB_DISCONNECT_PORT, &GPIO_InitStruct);
/* Enable USB FS Clock */
__USB_CLK_ENABLE();
/* Enable SYSCFG Clock */
__SYSCFG_CLK_ENABLE();
#if defined (USE_USB_INTERRUPT_REMAPPED)
/*USB interrupt remapping enable */
__HAL_REMAPINTERRUPT_USB_ENABLE();
#endif
#if defined (USE_USB_INTERRUPT_DEFAULT)
/* Set USB Default FS Interrupt priority */
HAL_NVIC_SetPriority(USB_LP_CAN_RX0_IRQn, 5, 0);
/* Enable USB FS Interrupt */
HAL_NVIC_EnableIRQ(USB_LP_CAN_RX0_IRQn);
#elif defined (USE_USB_INTERRUPT_REMAPPED)
/* Set USB Remapped FS Interrupt priority */
HAL_NVIC_SetPriority(USB_LP_IRQn, 5, 0);
/* Enable USB FS Interrupt */
HAL_NVIC_EnableIRQ(USB_LP_IRQn);
#endif
}
/**
* Initializes the Global MSP.
*/
void HAL_MspInit(void)
{
/* USER CODE BEGIN MspInit 0 */
/* USER CODE END MspInit 0 */
__SYSCFG_CLK_ENABLE();
/* System interrupt init*/
/* SysTick_IRQn interrupt configuration */
HAL_NVIC_SetPriority(SysTick_IRQn, 0, 0);
/* USER CODE BEGIN MspInit 1 */
/* USER CODE END MspInit 1 */
}
/**
* @brief DAC MSP Initialization
* This function configures the hardware resources used in this example:
* - Peripheral's clock enable
* - Peripheral's GPIO Configuration
* @param hdac: DAC handle pointer
* @retval None
*/
void HAL_DAC_MspInit(DAC_HandleTypeDef *hdac)
{
GPIO_InitTypeDef GPIO_InitStruct;
static DMA_HandleTypeDef hdma_dac1;
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO clock ****************************************/
DACx_CHANNEL_GPIO_CLK_ENABLE();
/* DAC Periph clock enable */
DACx_CLK_ENABLE();
/* DMA1 clock enable */
DMAx_CLK_ENABLE();
/* SYSCFG clock enable for DMA remapping */
__SYSCFG_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* DAC Channel1 GPIO pin configuration */
GPIO_InitStruct.Pin = DACx_CHANNEL_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(DACx_CHANNEL_GPIO_PORT, &GPIO_InitStruct);
/*##-3- Configure the DMA ##########################################*/
/* Set the parameters to be configured for DACx_DMA1_CHANNEL3 */
hdma_dac1.Instance = DACx_DMA_INSTANCE;
hdma_dac1.Init.Direction = DMA_MEMORY_TO_PERIPH;
hdma_dac1.Init.PeriphInc = DMA_PINC_DISABLE;
hdma_dac1.Init.MemInc = DMA_MINC_ENABLE;
hdma_dac1.Init.PeriphDataAlignment = DMA_PDATAALIGN_BYTE;
hdma_dac1.Init.MemDataAlignment = DMA_MDATAALIGN_BYTE;
hdma_dac1.Init.Mode = DMA_CIRCULAR;
hdma_dac1.Init.Priority = DMA_PRIORITY_HIGH;
HAL_DMA_Init(&hdma_dac1);
/* Associate the initialized DMA handle to the the DAC handle */
__HAL_LINKDMA(hdac, DMA_Handle1, hdma_dac1);
/*##-4- Configure the NVIC for DMA #########################################*/
/* Enable the DMA1_Channel3 IRQ Channel */
HAL_NVIC_SetPriority(DACx_DMA_IRQn, 2, 0);
HAL_NVIC_EnableIRQ(DACx_DMA_IRQn);
/*##-5- Configure the SYSCFG for DMA remapping #############################*/
__HAL_REMAPDMA_CHANNEL_ENABLE(HAL_REMAPDMA_TIM6_DAC1_CH1_DMA1_CH3);
}
void LBF_SysClkCfg(void)
{
// Derived from Cube MX Code Generator and EVAL152D USB MS example
RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
RCC_OscInitTypeDef RCC_OscInitStruct = {0};
// Enable HSE Oscillator and Activate PLL with HSE as source
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
RCC_OscInitStruct.HSEState = RCC_HSE_ON;
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL12;
RCC_OscInitStruct.PLL.PLLDIV = RCC_PLL_DIV3;
if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
{
// Error_Handler();
}
// Set Voltage scale1 as MCU will run at 32MHz
__PWR_CLK_ENABLE();
__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
// Poll VOSF bit of in PWR_CSR. Wait until it is reset to 0
// This indicates regulator has reached required voltage level
while (__HAL_PWR_GET_FLAG(PWR_FLAG_VOS) != RESET) {};
// Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers
// RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK;
RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK |
RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1) != HAL_OK)
{
// Error_Handler();
}
__SYSCFG_CLK_ENABLE();
// System Configuration Clock
// The system configuration controller is mainly used to remap the memory accessible in the
// code area, and manage the external interrupt line connection to the GPIOs.
}
/**
* Initializes the Global MSP.
*/
void HAL_MspInit(void)
{
/* USER CODE BEGIN MspInit 0 */
/* USER CODE END MspInit 0 */
__SYSCFG_CLK_ENABLE();
HAL_NVIC_SetPriorityGrouping(NVIC_PRIORITYGROUP_4);
/* System interrupt init*/
/* SysTick_IRQn interrupt configuration */
HAL_NVIC_SetPriority(SysTick_IRQn, 15, 0);
/* USER CODE BEGIN MspInit 1 */
/* USER CODE END MspInit 1 */
}
/**
* @brief COMP MSP Init
* @param hcomp : COMP handle
* @retval None
*/
void HAL_COMP_MspInit(COMP_HandleTypeDef *hcomp)
{
__SYSCFG_CLK_ENABLE();
/* GPIOB Peripheral clock enable */
__GPIOB_CLK_ENABLE();
/* Configure PB4 in analog mode: PB4 is connected to COMP2 non inverting input */
GPIO_InitStructure.Pin = GPIO_PIN_4;
GPIO_InitStructure.Mode = GPIO_MODE_ANALOG;
GPIO_InitStructure.Pull = GPIO_NOPULL;
GPIO_InitStructure.Speed = GPIO_SPEED_HIGH;
HAL_GPIO_Init(GPIOB, &GPIO_InitStructure);
/*## Configure the NVIC for COMP1 and COMP2 ###########################################*/
HAL_NVIC_SetPriority(ADC1_COMP_IRQn,0,0);
/* Enable the COMP1 and COMP2 global Interrupt */
HAL_NVIC_EnableIRQ(ADC1_COMP_IRQn);
}
//------------------------------------------------------------------------------------------------------------------------------------------------------
void Hardware_Init(void)
{
HAL_Init();
SystemClock_Config();
__GPIOA_CLK_ENABLE();
__GPIOB_CLK_ENABLE();
__GPIOC_CLK_ENABLE();
__GPIOD_CLK_ENABLE();
__GPIOE_CLK_ENABLE();
__GPIOF_CLK_ENABLE();
__GPIOG_CLK_ENABLE();
__DMA1_CLK_ENABLE(); // Для DAC1 (бикалка)
__TIM7_CLK_ENABLE(); // Для DAC1 (бикалка)
__DAC_CLK_ENABLE(); // Для бикалки
__PWR_CLK_ENABLE();
__SYSCFG_CLK_ENABLE();
HAL_NVIC_SetPriority(SysTick_IRQn, PRIORITY_SYS_TICK);
// Timer /////////////////////////////////////////////////////////////////
//RCC_PCLK1Config(RCC_HCLK_Div1);
// Таймер для мс
HAL_NVIC_SetPriority(TIM6_DAC_IRQn, PRIORITY_TIMER_TIM6);
HAL_NVIC_EnableIRQ(TIM6_DAC_IRQn);
Timer_Init();
Panel_Init();
FSMC_Init();
FSMC_SetMode(ModeFSMC_FPGA);
FDrive_Init();
}
/** System Clock Configuration
*/
void SystemClock_Config(void)
{
RCC_OscInitTypeDef RCC_OscInitStruct;
RCC_ClkInitTypeDef RCC_ClkInitStruct;
RCC_PeriphCLKInitTypeDef PeriphClkInit;
// Initialize the RCC Oscillators
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI|RCC_OSCILLATORTYPE_HSI14;
RCC_OscInitStruct.HSIState = RCC_HSI_ON;
RCC_OscInitStruct.HSI14State = RCC_HSI14_ON;
RCC_OscInitStruct.HSICalibrationValue = 16;
RCC_OscInitStruct.HSI14CalibrationValue = 16;
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI; // HSI = 8 MHz
RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL6; // PLL = 8x6 = 48 MHz
RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV1;
HAL_RCC_OscConfig(&RCC_OscInitStruct);
// Initialize the CPU, AHB and APB busses clocks
RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK;
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 48 MHz
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 48 MHz
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1; // 48 MHz
HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1);
// Initialize the RCC extended peripherals clocks
PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USART3|RCC_PERIPHCLK_USART1
|RCC_PERIPHCLK_USART2;
PeriphClkInit.Usart1ClockSelection = RCC_USART1CLKSOURCE_PCLK1;
PeriphClkInit.Usart2ClockSelection = RCC_USART2CLKSOURCE_PCLK1;
PeriphClkInit.Usart3ClockSelection = RCC_USART3CLKSOURCE_PCLK1;
HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit);
__SYSCFG_CLK_ENABLE();
/* System interrupt init*/
/* SysTick_IRQn interrupt configuration */
HAL_NVIC_SetPriority(SysTick_IRQn, 0, 0);
}
void SystemClock_Config(void) {
RCC_OscInitTypeDef RCC_OscInitStruct;
RCC_ClkInitTypeDef RCC_ClkInitStruct;
RCC_PeriphCLKInitTypeDef PeriphClkInit;
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI48;
RCC_OscInitStruct.HSI48State = RCC_HSI48_ON;
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE;
HAL_RCC_OscConfig(&RCC_OscInitStruct);
RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK;
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_HSI48;
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1);
PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USB;
PeriphClkInit.UsbClockSelection = RCC_USBCLKSOURCE_HSI48;
HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit);
__SYSCFG_CLK_ENABLE();
}
/**
* @brief Initializes the PCD MSP.
* @param hpcd: PCD handle
* @retval None
*/
void HAL_PCD_MspInit(PCD_HandleTypeDef *hpcd)
{
GPIO_InitTypeDef GPIO_InitStruct;
/* Enable the GPIOA clock for USB DataLines */
__GPIOA_CLK_ENABLE();
/* Enable the GPIOC clock for USB external Pull-Up */
__GPIOC_CLK_ENABLE();
/* Configure USB DM and DP pins */
GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12);
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF14_USB;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
GPIO_InitStruct.Pin = USB_DISCONNECT_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_OD;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
HAL_GPIO_Init(USB_DISCONNECT_PORT, &GPIO_InitStruct);
/* Enable USB FS Clock */
__USB_CLK_ENABLE();
/* Enable SYSCFG Clock */
__SYSCFG_CLK_ENABLE();
/* Set USB FS Interrupt priority */
HAL_NVIC_SetPriority(USB_LP_IRQn, 5, 0);
/* Enable USB FS Interrupt */
HAL_NVIC_EnableIRQ(USB_LP_IRQn);
}
void checkForBootLoaderRequest(void)
{
uint32_t bt;
__PWR_CLK_ENABLE();
__BKPSRAM_CLK_ENABLE();
HAL_PWR_EnableBkUpAccess();
bt = (*(__IO uint32_t *) (BKPSRAM_BASE + 4)) ;
if ( bt == 0xDEADBEEF ) {
(*(__IO uint32_t *) (BKPSRAM_BASE + 4)) = 0xCAFEFEED; // Reset our trigger
// Backup SRAM is write-back by default, ensure value actually reaches memory
// Another solution would be marking BKPSRAM as write-through in Memory Protection Unit settings
SCB_CleanDCache_by_Addr((uint32_t *) (BKPSRAM_BASE + 4), sizeof(uint32_t));
void (*SysMemBootJump)(void);
__SYSCFG_CLK_ENABLE();
SYSCFG->MEMRMP |= SYSCFG_MEM_BOOT_ADD0 ;
uint32_t p = (*((uint32_t *) 0x1ff00000));
__set_MSP(p); //Set the main stack pointer to its defualt values
SysMemBootJump = (void (*)(void)) (*((uint32_t *) 0x1ff00004)); // Point the PC to the System Memory reset vector (+4)
SysMemBootJump();
while (1);
}
}
/**
* @brief Configures I2C Interrupt.
* @param None
* @retval None
*/
static void I2Cx_ITConfig(void)
{
static uint8_t I2C_IT_Enabled = 0;
GPIO_InitTypeDef GPIO_InitStruct;
if(I2C_IT_Enabled == 0)
{
I2C_IT_Enabled = 1;
/* Enable the GPIO EXTI clock */
__GPIOI_CLK_ENABLE();
__SYSCFG_CLK_ENABLE();
GPIO_InitStruct.Pin = GPIO_PIN_2;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_FAST;
GPIO_InitStruct.Mode = GPIO_MODE_IT_FALLING;
HAL_GPIO_Init(GPIOI, &GPIO_InitStruct);
/* Set priority and Enable GPIO EXTI Interrupt */
HAL_NVIC_SetPriority((IRQn_Type)(EXTI2_IRQn), 5, 0);
HAL_NVIC_EnableIRQ((IRQn_Type)(EXTI2_IRQn));
}
}
void LBF_SysClkCfg(void)
{
// Derived from Cube MX Code Generator
RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
RCC_OscInitTypeDef RCC_OscInitStruct = {0};
RCC_PeriphCLKInitTypeDef PeriphClkInit;
// Enable HSE Oscillator and Activate PLL with HSE as source
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
RCC_OscInitStruct.HSEState = RCC_HSE_ON;
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
RCC_OscInitStruct.PLL.PLLM = 1;
RCC_OscInitStruct.PLL.PLLN = 20;
RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV7; // unused for now
RCC_OscInitStruct.PLL.PLLQ = RCC_PLLQ_DIV8; // unused for now
RCC_OscInitStruct.PLL.PLLR = RCC_PLLR_DIV2; // 8MHz*20/2 = 80MHz
if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
{
// Error_Handler();
}
__PWR_CLK_ENABLE();
// Set Voltage scale to Range 1 to allow operation up to 80MHz
// (internal regulator will provide 1.2V typical)
HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1);
// Poll VOSF bit of in PWR_CSR. Wait until it is reset to 0
// This indicates regulator has reached required voltage level
while (__HAL_PWR_GET_FLAG(PWR_FLAG_VOSF) != RESET) {};
// Select PLL as system clock source
// and configure the HCLK, PCLK1 and PCLK2 clocks dividers
RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
|RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // SYSCLK = 80MHz
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // AHBCLK (HCLK) = 80MHz to Cortex
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // APB1 periph clock = 20MHz
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV4; // APB2 periph clock = 20MHz
if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4) != HAL_OK)
// Flash Latency proposed by CubeMX
{
// Error_Handler();
}
// USB clock source
PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USB;
PeriphClkInit.UsbClockSelection = RCC_USBCLKSOURCE_PLLSAI1;
PeriphClkInit.PLLSAI1.PLLSAI1N = 12;
PeriphClkInit.PLLSAI1.PLLSAI1P = RCC_PLLP_DIV7;
PeriphClkInit.PLLSAI1.PLLSAI1Q = RCC_PLLQ_DIV2; // USB clock= 8MHz*12/2 = 48MHz
PeriphClkInit.PLLSAI1.PLLSAI1R = RCC_PLLR_DIV2;
HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit);
// SysTick clock source -
HAL_SYSTICK_Config(HAL_RCC_GetHCLKFreq()/8000);
HAL_SYSTICK_CLKSourceConfig(SYSTICK_CLKSOURCE_HCLK_DIV8);
// sets SysTick to generate 1 tick every HclkFreq/8000*8 cycle of Hclk ie. every 1ms
__SYSCFG_CLK_ENABLE();
// System Configuration Clock
// The system configuration controller is mainly used to remap the memory accessible in the
// code area, and manage the external interrupt line connection to the GPIOs.
// NOTE: RTC configuration is done separately, refer to LBF_LSE_RTC_Cfg.c
/*
HClkFqcy = HAL_RCC_GetHCLKFreq(); //NEEDED
APB1ClkFqcy = HAL_RCC_GetPCLK1Freq(); //NEEDED
APB2ClkFqcy = HAL_RCC_GetPCLK2Freq(); // NEEDED
*/
}
void Hardware_Init()
{
HAL_Init();
SystemClock_Config();
__GPIOA_CLK_ENABLE();
__GPIOB_CLK_ENABLE();
__GPIOC_CLK_ENABLE();
__GPIOD_CLK_ENABLE();
__GPIOE_CLK_ENABLE();
__GPIOF_CLK_ENABLE();
__GPIOG_CLK_ENABLE();
__DMA1_CLK_ENABLE(); // Для DAC1 (бикалка)
__TIM6_CLK_ENABLE(); // Для отсчёта миллисекунд
__TIM2_CLK_ENABLE(); // Для тиков
__TIM7_CLK_ENABLE(); // Для DAC1 (бикалка)
__DAC_CLK_ENABLE(); // Для бикалки
__PWR_CLK_ENABLE();
__SYSCFG_CLK_ENABLE();
HAL_NVIC_SetPriority(SysTick_IRQn, 0, 0);
// Timer /////////////////////////////////////////////////////////////////
//RCC_PCLK1Config(RCC_HCLK_Div1);
// Таймер для мс
HAL_NVIC_SetPriority(TIM6_DAC_IRQn, 2, 0);
HAL_NVIC_EnableIRQ(TIM6_DAC_IRQn);
if (HAL_TIM_Base_Init(&handleTIM6forTimer) != HAL_OK)
{
HARDWARE_ERROR
}
if (HAL_TIM_Base_Start_IT(&handleTIM6forTimer) != HAL_OK)
{
HARDWARE_ERROR
}
// Таймер для тиков
TIM_HandleTypeDef tim2handle =
{
TIM2,
{
0,
TIM_COUNTERMODE_UP,
0xffffffff,
TIM_CLOCKDIVISION_DIV1
}
};
if (HAL_TIM_Base_Init(&tim2handle) != HAL_OK)
{
HARDWARE_ERROR
}
if (HAL_TIM_Base_Start(&tim2handle) != HAL_OK)
{
HARDWARE_ERROR
}
Sound_Init();
#ifdef SPI_ENABLE
Panel_Init();
#endif
FSMC_Init();
ADC_Init();
FDrive_Init();
// Analog and DAC programmable SPI ////////////////////////////////////////
GPIO_InitTypeDef isGPIOG =
{
GPIO_PIN_2 | GPIO_PIN_3 | GPIO_PIN_5 | GPIO_PIN_7, // GPIO_PIN_1 - для работы с дисплеем
GPIO_MODE_OUTPUT_PP,
GPIO_NOPULL,
GPIO_SPEED_HIGH,
GPIO_AF0_MCO
};
HAL_GPIO_Init(GPIOG, &isGPIOG);
isGPIOG.Pin = GPIO_PIN_1;
isGPIOG.Mode = GPIO_MODE_OUTPUT_PP;
isGPIOG.Pull = GPIO_NOPULL;
HAL_GPIO_Init(GPIOG, &isGPIOG);
HAL_GPIO_WritePin(GPIOG, GPIO_PIN_1, GPIO_PIN_RESET); // PG1 - когда равен 1, чтение дисплея, в остальных случаях 0
RTC_Init();
}
/**
* @brief UART MSP Initialization
* This function configures the hardware resources used in this example:
* - Peripheral's clock enable
* - Peripheral's GPIO Configuration
* - NVIC configuration for UART interrupt request enable
* @param huart: UART handle pointer
* @retval None
*/
void HAL_UART_MspInit(UART_HandleTypeDef *huart)
{
GPIO_InitTypeDef GPIO_InitStruct;
switch((uint32_t)huart->Instance)
{
case (uint32_t)USART1 :
{
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO TX/RX clock */
__GPIOA_CLK_ENABLE();
/* Enable USARTx clock */
__USART1_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* UART TX GPIO pin configuration */
GPIO_InitStruct.Pin = GPIO_PIN_9 | GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF1_USART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/*##-3- Configure the NVIC for UART ########################################*/
/* NVIC for USART */
HAL_NVIC_SetPriority(USART1_IRQn, 1, 0);
HAL_NVIC_EnableIRQ(USART1_IRQn);
}
break;
case (uint32_t)USART2 :
{
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO TX/RX clock */
__GPIOD_CLK_ENABLE();
/* Enable USARTx clock */
__USART2_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* UART TX GPIO pin configuration */
GPIO_InitStruct.Pin = GPIO_PIN_6 | GPIO_PIN_5;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF0_USART2;
HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
/*##-3- Configure the NVIC for UART ########################################*/
/* NVIC for USART */
HAL_NVIC_SetPriority(USART2_IRQn, 1, 0);
HAL_NVIC_EnableIRQ(USART2_IRQn);
}
break;
case (uint32_t)USART3 :
{
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO TX/RX clock */
__GPIOD_CLK_ENABLE();
/* To allow the IT source identification */
__SYSCFG_CLK_ENABLE();
/* Enable USARTx clock */
__USART3_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* UART TX GPIO pin configuration */
GPIO_InitStruct.Pin = GPIO_PIN_8 | GPIO_PIN_9;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF0_USART3;
HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
/*##-3- Configure the NVIC for UART ########################################*/
/* NVIC for USART */
HAL_NVIC_SetPriority(USART3_8_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(USART3_8_IRQn);
}
break;
case (uint32_t)USART4 :
{
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO TX/RX clock */
__GPIOC_CLK_ENABLE();
/* To allow the IT source identification */
__SYSCFG_CLK_ENABLE();
/* Enable USARTx clock */
__USART4_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* UART TX GPIO pin configuration */
GPIO_InitStruct.Pin = GPIO_PIN_10 | GPIO_PIN_11;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF0_USART4;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
/*##-3- Configure the NVIC for UART ########################################*/
/* NVIC for USART */
HAL_NVIC_SetPriority(USART3_8_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(USART3_8_IRQn);
}
break;
case (uint32_t)USART5 :
{
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO TX/RX clock */
__GPIOB_CLK_ENABLE();
/* To allow the IT source identification */
__SYSCFG_CLK_ENABLE();
/* Enable USARTx clock */
__USART5_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* UART TX GPIO pin configuration */
GPIO_InitStruct.Pin = GPIO_PIN_3 | GPIO_PIN_4;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF4_USART5;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
/*##-3- Configure the NVIC for UART ########################################*/
/* NVIC for USART */
HAL_NVIC_SetPriority(USART3_8_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(USART3_8_IRQn);
}
break;
case (uint32_t)USART6 :
{
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO TX/RX clock */
__GPIOF_CLK_ENABLE();
/* To allow the IT source identification */
__SYSCFG_CLK_ENABLE();
/* Enable USARTx clock */
__USART6_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* UART TX GPIO pin configuration */
GPIO_InitStruct.Pin = GPIO_PIN_9 | GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF1_USART6;
HAL_GPIO_Init(GPIOF, &GPIO_InitStruct);
/*##-3- Configure the NVIC for UART ########################################*/
/* NVIC for USART */
HAL_NVIC_SetPriority(USART3_8_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(USART3_8_IRQn);
}
break;
case (uint32_t)USART7 :
{
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO TX/RX clock */
__GPIOF_CLK_ENABLE();
/* To allow the IT source identification */
__SYSCFG_CLK_ENABLE();
/* Enable USARTx clock */
__USART7_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* UART TX GPIO pin configuration */
GPIO_InitStruct.Pin = GPIO_PIN_3 | GPIO_PIN_2;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF1_USART7;
HAL_GPIO_Init(GPIOF, &GPIO_InitStruct);
/*##-3- Configure the NVIC for UART ########################################*/
/* NVIC for USART */
HAL_NVIC_SetPriority(USART3_8_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(USART3_8_IRQn);
}
break;
case (uint32_t)USART8 :
{
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO TX/RX clock */
__GPIOC_CLK_ENABLE();
/* To allow the IT source identification */
__SYSCFG_CLK_ENABLE();
/* Enable USARTx clock */
__USART8_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* UART TX GPIO pin configuration */
GPIO_InitStruct.Pin = GPIO_PIN_8 | GPIO_PIN_9;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF1_USART8;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
/*##-3- Configure the NVIC for UART ########################################*/
/* NVIC for USART */
HAL_NVIC_SetPriority(USART3_8_IRQn, 1, 0);
HAL_NVIC_EnableIRQ(USART3_8_IRQn);
}
break;
}
}
/**
* @brief Initializes the OPAMP according to the specified
* parameters in the OPAMP_InitTypeDef and create the associated handle.
* @note If the selected opamp is locked, initialization can't be performed.
* To unlock the configuration, perform a system reset.
* @param hopamp: OPAMP handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_OPAMP_Init(OPAMP_HandleTypeDef *hopamp)
{
HAL_StatusTypeDef status = HAL_OK;
/* Check the OPAMP handle allocation and lock status */
/* Init not allowed if calibration is ongoing */
if((hopamp == NULL) || (hopamp->State == HAL_OPAMP_STATE_BUSYLOCKED) \
|| (hopamp->State == HAL_OPAMP_STATE_CALIBBUSY))
{
return HAL_ERROR;
}
else
{
/* Check the parameter */
assert_param(IS_OPAMP_ALL_INSTANCE(hopamp->Instance));
/* Set OPAMP parameters */
assert_param(IS_OPAMP_FUNCTIONAL_NORMALMODE(hopamp->Init.Mode));
assert_param(IS_OPAMP_NONINVERTING_INPUT(hopamp->Init.NonInvertingInput));
if (((hopamp->Init.Mode) == OPAMP_STANDALONE_MODE) || ((hopamp->Init.Mode) == OPAMP_PGA_MODE))
{
assert_param(IS_OPAMP_INVERTING_INPUT(hopamp->Init.InvertingInput));
}
assert_param(IS_OPAMP_TIMERCONTROLLED_MUXMODE(hopamp->Init.TimerControlledMuxmode));
if ((hopamp->Init.TimerControlledMuxmode) == OPAMP_TIMERCONTROLLEDMUXMODE_ENABLE)
{
assert_param(IS_OPAMP_SEC_NONINVERTINGINPUT(hopamp->Init.NonInvertingInputSecondary));
if (((hopamp->Init.Mode) == OPAMP_STANDALONE_MODE) || ((hopamp->Init.Mode) == OPAMP_PGA_MODE))
{
assert_param(IS_OPAMP_SEC_INVERTINGINPUT(hopamp->Init.InvertingInputSecondary));
}
}
if ((hopamp->Init.Mode) == OPAMP_PGA_MODE)
{
assert_param(IS_OPAMP_PGACONNECT(hopamp->Init.PgaConnect));
assert_param(IS_OPAMP_PGA_GAIN(hopamp->Init.PgaGain));
}
assert_param(IS_OPAMP_TRIMMING(hopamp->Init.UserTrimming));
if ((hopamp->Init.UserTrimming) == OPAMP_TRIMMING_USER)
{
assert_param(IS_OPAMP_TRIMMINGVALUE(hopamp->Init.TrimmingValueP));
assert_param(IS_OPAMP_TRIMMINGVALUE(hopamp->Init.TrimmingValueN));
}
/* Init SYSCFG and the low level hardware to access opamp */
__SYSCFG_CLK_ENABLE();
/* Call MSP init function */
HAL_OPAMP_MspInit(hopamp);
/* Set OPAMP parameters */
/* Set bits according to hopamp->hopamp->Init.Mode value */
/* Set bits according to hopamp->hopamp->Init.InvertingInput value */
/* Set bits according to hopamp->hopamp->Init.NonInvertingInput value */
/* Set bits according to hopamp->hopamp->Init.TimerControlledMuxmode value */
/* Set bits according to hopamp->hopamp->Init.InvertingInputSecondary value */
/* Set bits according to hopamp->hopamp->Init.NonInvertingInputSecondary value */
/* Set bits according to hopamp->hopamp->Init.PgaConnect value */
/* Set bits according to hopamp->hopamp->Init.PgaGain value */
/* Set bits according to hopamp->hopamp->Init.UserTrimming value */
/* Set bits according to hopamp->hopamp->Init.TrimmingValueP value */
/* Set bits according to hopamp->hopamp->Init.TrimmingValueN value */
/* check if OPAMP_PGA_MODE & in Follower mode */
/* - InvertingInput */
/* - InvertingInputSecondary */
/* are Not Applicable */
if ((hopamp->Init.Mode == OPAMP_PGA_MODE) || (hopamp->Init.Mode == OPAMP_FOLLOWER_MODE))
{
MODIFY_REG(hopamp->Instance->CSR, OPAMP_CSR_UPDATE_PARAMETERS_INIT_MASK, \
hopamp->Init.Mode | \
hopamp->Init.NonInvertingInput | \
hopamp->Init.TimerControlledMuxmode | \
hopamp->Init.NonInvertingInputSecondary | \
hopamp->Init.PgaConnect | \
hopamp->Init.PgaGain | \
hopamp->Init.UserTrimming | \
(hopamp->Init.TrimmingValueP << OPAMP_INPUT_NONINVERTING) | \
(hopamp->Init.TrimmingValueN << OPAMP_INPUT_INVERTING));
}
else
{
MODIFY_REG(hopamp->Instance->CSR, OPAMP_CSR_UPDATE_PARAMETERS_INIT_MASK, \
hopamp->Init.Mode | \
hopamp->Init.InvertingInput | \
hopamp->Init.NonInvertingInput | \
hopamp->Init.TimerControlledMuxmode | \
hopamp->Init.InvertingInputSecondary | \
hopamp->Init.NonInvertingInputSecondary | \
hopamp->Init.PgaConnect | \
hopamp->Init.PgaGain | \
hopamp->Init.UserTrimming | \
(hopamp->Init.TrimmingValueP << OPAMP_INPUT_NONINVERTING) | \
(hopamp->Init.TrimmingValueN << OPAMP_INPUT_INVERTING));
}
/* Update the OPAMP state*/
if (hopamp->State == HAL_OPAMP_STATE_RESET)
{
/* From RESET state to READY State */
hopamp->State = HAL_OPAMP_STATE_READY;
}
/* else: remain in READY or BUSY state (no update) */
return status;
}
}
//------------------------------------------------------------------------------------------------------------------------------------------------------
void Hardware_Init(void)
{
HAL_Init();
SystemClock_Config();
#ifndef _MS_VS
__GPIOA_CLK_ENABLE();
__GPIOB_CLK_ENABLE();
__GPIOC_CLK_ENABLE();
__GPIOD_CLK_ENABLE();
__GPIOE_CLK_ENABLE();
__GPIOF_CLK_ENABLE();
__GPIOG_CLK_ENABLE();
__DMA1_CLK_ENABLE(); // Для DAC1 (бикалка)
__TIM7_CLK_ENABLE(); // Для DAC1 (бикалка)
__DAC_CLK_ENABLE(); // Для бикалки
__PWR_CLK_ENABLE();
__SYSCFG_CLK_ENABLE();
#endif
HAL_NVIC_SetPriority(SysTick_IRQn, PRIORITY_SYS_TICK);
// Timer /////////////////////////////////////////////////////////////////
//RCC_PCLK1Config(RCC_HCLK_Div1);
// Таймер для мс
HAL_NVIC_SetPriority(TIM6_DAC_IRQn, PRIORITY_TIMER_TIM6);
HAL_NVIC_EnableIRQ(TIM6_DAC_IRQn);
Timer_Init();
Sound_Init();
Panel_Init();
FSMC_Init();
FSMC_SetMode(ModeFSMC_FPGA);
RAM_Init();
FDrive_Init();
// Analog and DAC programmable SPI ////////////////////////////////////////
GPIO_InitTypeDef isGPIO =
{
GPIO_PIN_10 | GPIO_PIN_12, // SPI SCLK, DATA
GPIO_MODE_OUTPUT_PP,
GPIO_NOPULL,
GPIO_SPEED_HIGH,
GPIO_AF0_MCO
};
HAL_GPIO_Init(GPIOC, &isGPIO);
isGPIO.Pin = GPIO_PIN_3 | GPIO_PIN_6; // SPI select1, select2
HAL_GPIO_Init(GPIOD, &isGPIO);
isGPIO.Pin = GPIO_PIN_10 | GPIO_PIN_15; // SPI select3, select4
HAL_GPIO_Init(GPIOG, &isGPIO);
RTC_Init();
}
/**
* @brief Initializes the COMP according to the specified
* parameters in the COMP_InitTypeDef and create the associated handle.
* @note If the selected comparator is locked, initialization can't be performed.
* To unlock the configuration, perform a system reset.
* @param hcomp: COMP handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_COMP_Init(COMP_HandleTypeDef *hcomp)
{
HAL_StatusTypeDef status = HAL_OK;
uint32_t regshift = COMP_CSR_COMP1_SHIFT;
/* Check the COMP handle allocation and lock status */
if((hcomp == NULL) || ((hcomp->State & COMP_STATE_BIT_LOCK) != RESET))
{
status = HAL_ERROR;
}
else
{
/* Check the parameter */
assert_param(IS_COMP_ALL_INSTANCE(hcomp->Instance));
assert_param(IS_COMP_INVERTINGINPUT(hcomp->Init.InvertingInput));
assert_param(IS_COMP_NONINVERTINGINPUT(hcomp->Init.NonInvertingInput));
assert_param(IS_COMP_OUTPUT(hcomp->Init.Output));
assert_param(IS_COMP_OUTPUTPOL(hcomp->Init.OutputPol));
assert_param(IS_COMP_HYSTERESIS(hcomp->Init.Hysteresis));
assert_param(IS_COMP_MODE(hcomp->Init.Mode));
if(hcomp->Init.NonInvertingInput == COMP_NONINVERTINGINPUT_DAC1SWITCHCLOSED)
{
assert_param(IS_COMP_DAC1SWITCH_INSTANCE(hcomp->Instance));
}
if(hcomp->Init.WindowMode != COMP_WINDOWMODE_DISABLED)
{
assert_param(IS_COMP_WINDOWMODE_INSTANCE(hcomp->Instance));
}
if(hcomp->State == HAL_COMP_STATE_RESET)
{
/* Init SYSCFG and the low level hardware to access comparators */
__SYSCFG_CLK_ENABLE();
HAL_COMP_MspInit(hcomp);
}
/* Set COMP parameters */
/* Set COMPxINSEL bits according to hcomp->Init.InvertingInput value */
/* Set COMPxOUTSEL bits according to hcomp->Init.Output value */
/* Set COMPxPOL bit according to hcomp->Init.OutputPol value */
/* Set COMPxHYST bits according to hcomp->Init.Hysteresis value */
/* Set COMPxMODE bits according to hcomp->Init.Mode value */
if(hcomp->Instance == COMP2)
{
regshift = COMP_CSR_COMP2_SHIFT;
}
MODIFY_REG(COMP->CSR,
(uint32_t)(COMP_CSR_COMPxINSEL | COMP_CSR_COMPxNONINSEL_MASK | \
COMP_CSR_COMPxOUTSEL | COMP_CSR_COMPxPOL | \
COMP_CSR_COMPxHYST | COMP_CSR_COMPxMODE) << regshift,
(hcomp->Init.InvertingInput | \
hcomp->Init.NonInvertingInput | \
hcomp->Init.Output | \
hcomp->Init.OutputPol | \
hcomp->Init.Hysteresis | \
hcomp->Init.Mode) << regshift);
if(hcomp->Init.WindowMode != COMP_WINDOWMODE_DISABLED)
{
COMP->CSR |= COMP_CSR_WNDWEN;
}
/* Initialize the COMP state*/
if(hcomp->State == HAL_COMP_STATE_RESET)
{
hcomp->State = HAL_COMP_STATE_READY;
}
}
return status;
}
/**
* @brief Initializes the COMP according to the specified
* parameters in the COMP_InitTypeDef and create the associated handle.
* @note If the selected comparator is locked, initialization can't be performed.
* To unlock the configuration, perform a system reset.
* @param hcomp: COMP handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_COMP_Init(COMP_HandleTypeDef *hcomp)
{
HAL_StatusTypeDef status = HAL_OK;
/* Check the COMP handle allocation and lock status */
if((hcomp == HAL_NULL) || ((hcomp->State & COMP_STATE_BIT_LOCK) != RESET))
{
status = HAL_ERROR;
}
else
{
/* Check the parameter */
assert_param(IS_COMP_ALL_INSTANCE(hcomp->Instance));
if (hcomp->Instance == COMP1)
{
assert_param(IS_COMP_NONINVERTINGINPUTPULL(hcomp->Init.NonInvertingInputPull));
}
else /* if (hcomp->Instance == COMP2) */
{
assert_param(IS_COMP_INVERTINGINPUT(hcomp->Init.InvertingInput));
assert_param(IS_COMP_OUTPUT(hcomp->Init.Output));
assert_param(IS_COMP_MODE(hcomp->Init.Mode));
assert_param(IS_COMP_WINDOWMODE(hcomp->Init.WindowMode));
}
/* In window mode, non-inverting inputs of the 2 comparators are */
/* connected together and are using inputs of COMP2 only. If COMP1 is */
/* selected, this parameter is discarded. */
if ((hcomp->Init.WindowMode == COMP_WINDOWMODE_DISABLED) ||
(hcomp->Instance == COMP2) )
{
assert_param(IS_COMP_NONINVERTINGINPUT(hcomp->Init.NonInvertingInput));
}
/* Enable SYSCFG clock and the low level hardware to access comparators */
if(hcomp->State == HAL_COMP_STATE_RESET)
{
/* Enable SYSCFG clock to control the routing Interface (RI) */
__SYSCFG_CLK_ENABLE();
/* Init the low level hardware */
HAL_COMP_MspInit(hcomp);
}
/* Configuration of comparator: */
/* - Output selection */
/* - Inverting input selection */
/* - Window mode */
/* - Mode fast/slow speed */
/* - Inverting input pull-up/down resistors */
/* Configuration depending on comparator instance */
if (hcomp->Instance == COMP1)
{
MODIFY_REG(COMP->CSR, COMP_CSR_400KPD | COMP_CSR_10KPD | COMP_CSR_400KPU | COMP_CSR_10KPU,
hcomp->Init.NonInvertingInputPull );
}
else /* if (hcomp->Instance == COMP2) */
{
/* Note: If comparator 2 is not enabled, inverting input (parameter */
/* "hcomp->Init.InvertingInput") is configured into function */
/* "HAL_COMP_Start()" since inverting input selection also */
/* enables the comparator 2. */
/* If comparator 2 is already enabled, inverting input is */
/* reconfigured on the fly. */
if (__COMP_IS_ENABLED(hcomp) == RESET)
{
MODIFY_REG(COMP->CSR, COMP_CSR_OUTSEL |
COMP_CSR_WNDWE |
COMP_CSR_SPEED ,
hcomp->Init.Output |
hcomp->Init.WindowMode |
hcomp->Init.Mode );
}
else
{
MODIFY_REG(COMP->CSR, COMP_CSR_OUTSEL |
COMP_CSR_INSEL |
COMP_CSR_WNDWE |
COMP_CSR_SPEED ,
hcomp->Init.Output |
hcomp->Init.InvertingInput |
hcomp->Init.WindowMode |
hcomp->Init.Mode );
}
}
/* Configure Routing Interface (RI) switches for comparator non-inverting */
/* input. */
/* Except in 2 cases: */
/* - if non-inverting input has no selection: it can be the case for */
/* COMP1 in window mode. */
/* - particular case for PC3: if switch COMP1_SW1 is closed */
/* (by macro "__HAL_OPAMP_OPAMP3OUT_CONNECT_ADC_COMP1()" or */
/* "__HAL_RI_SWITCH_COMP1_SW1_CLOSE()"), connection between pin PC3 */
/* (or OPAMP3, if available) and COMP1 is done directly, without going */
/* through ADC switch matrix. */
if (__COMP_ROUTING_INTERFACE_TOBECONFIGURED(hcomp))
{
if (hcomp->Instance == COMP1)
{
/* Enable the switch control mode */
__HAL_RI_SWITCHCONTROLMODE_ENABLE();
/* Close the analog switch of ADC switch matrix to COMP1 (ADC */
/* channel 26: Vcomp) */
__HAL_RI_IOSWITCH_CLOSE(RI_IOSWITCH_VCOMP);
}
/* Close the I/O analog switch corresponding to comparator */
/* non-inverting input selected. */
__HAL_RI_IOSWITCH_CLOSE(hcomp->Init.NonInvertingInput);
}
/* Initialize the COMP state*/
if(hcomp->State == HAL_COMP_STATE_RESET)
{
hcomp->State = HAL_COMP_STATE_READY;
}
}
return status;
}
/**
* @brief Initializes the PCD MSP.
* @param hpcd: PCD handle
* @retval None
*/
void HAL_PCD_MspInit(PCD_HandleTypeDef *hpcd)
{
GPIO_InitTypeDef GPIO_InitStruct;
/* Enable the GPIOA clock for USB DataLines */
__GPIOA_CLK_ENABLE();
/* Enable the GPIOB clock for USB external Pull-Up */
__GPIOB_CLK_ENABLE();
/* Configure USB DM and DP pins */
GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12);
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* Enable USB FS Clock */
__USB_CLK_ENABLE();
/* Enable SYSCFG Clock */
__SYSCFG_CLK_ENABLE();
#if defined (USE_USB_INTERRUPT_REMAPPED)
/*USB interrupt remapping enable */
__HAL_REMAPINTERRUPT_USB_ENABLE();
#endif
if(hpcd->Init.low_power_enable == 1)
{
/* Enable EXTI Line 18 for USB wakeup */
__HAL_USB_EXTI_CLEAR_FLAG();
__HAL_USB_EXTI_SET_RISING_EDGE_TRIGGER();
__HAL_USB_EXTI_ENABLE_IT();
#if defined (USE_USB_INTERRUPT_DEFAULT)
/* USB Default Wakeup Interrupt */
HAL_NVIC_EnableIRQ(USBWakeUp_IRQn);
/* Enable USB Wake-up interrupt */
HAL_NVIC_SetPriority(USBWakeUp_IRQn, 0, 0);
#elif defined (USE_USB_INTERRUPT_REMAPPED)
/* USB Remapped Wakeup Interrupt */
HAL_NVIC_EnableIRQ(USBWakeUp_RMP_IRQn);
/* Enable USB Wake-up interrupt */
HAL_NVIC_SetPriority(USBWakeUp_RMP_IRQn, 0, 0);
#endif
}
#if defined (USE_USB_INTERRUPT_DEFAULT)
/* Set USB Default FS Interrupt priority */
HAL_NVIC_SetPriority(USB_LP_CAN_RX0_IRQn, 0x0F, 0);
/* Enable USB FS Interrupt */
HAL_NVIC_EnableIRQ(USB_LP_CAN_RX0_IRQn);
#elif defined (USE_USB_INTERRUPT_REMAPPED)
/* Set USB Remapped FS Interrupt priority */
HAL_NVIC_SetPriority(USB_LP_IRQn, 0x0F, 0);
/* Enable USB FS Interrupt */
HAL_NVIC_EnableIRQ(USB_LP_IRQn);
#endif
}