Ejemplos de __UART5_RELEASE_RESET en C++ (Cpp)

Ejemplo n.º 1

Archivo: serial_device.c Proyecto: Archcady/mbed-os

void serial_free(serial_t *obj)
{
    struct serial_s *obj_s = SERIAL_S(obj);
      
    // Reset UART and disable clock
    if (obj_s->uart == UART_1) {
        __USART1_FORCE_RESET();
        __USART1_RELEASE_RESET();
        __USART1_CLK_DISABLE();
    }
    if (obj_s->uart == UART_2) {
        __USART2_FORCE_RESET();
        __USART2_RELEASE_RESET();
        __USART2_CLK_DISABLE();
    }
#if defined(USART3_BASE)
    if (obj_s->uart == UART_3) {
        __USART3_FORCE_RESET();
        __USART3_RELEASE_RESET();
        __USART3_CLK_DISABLE();
    }
#endif
#if defined(UART4_BASE)
    if (obj_s->uart == UART_4) {
        __UART4_FORCE_RESET();
        __UART4_RELEASE_RESET();
        __UART4_CLK_DISABLE();
    }
#endif
#if defined(UART5_BASE)
    if (obj_s->uart == UART_5) {
        __UART5_FORCE_RESET();
        __UART5_RELEASE_RESET();
        __UART5_CLK_DISABLE();
    }
#endif

    // Configure GPIOs
    pin_function(obj_s->pin_tx, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, 0));
    pin_function(obj_s->pin_rx, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, 0));

    serial_irq_ids[obj_s->index] = 0;
}

Ejemplo n.º 2

Archivo: serial_api.c Proyecto: antonio-salieri/mbed

void serial_free(serial_t *obj) {
    // Reset UART and disable clock
    switch (obj->uart) {
        case UART_1:
            __USART1_FORCE_RESET();
            __USART1_RELEASE_RESET();
            __USART1_CLK_DISABLE();
            break;
        case UART_2:
            __USART2_FORCE_RESET();
            __USART2_RELEASE_RESET();
            __USART2_CLK_DISABLE();
            break;
        case UART_3:
            __USART3_FORCE_RESET();
            __USART3_RELEASE_RESET();
            __USART3_CLK_DISABLE();
            break;
        case UART_4:
            __UART4_FORCE_RESET();
            __UART4_RELEASE_RESET();
            __UART4_CLK_DISABLE();
            break;
        case UART_5:
            __UART5_FORCE_RESET();
            __UART5_RELEASE_RESET();
            __UART5_CLK_DISABLE();
            break;
        case UART_6:
            __USART6_FORCE_RESET();
            __USART6_RELEASE_RESET();
            __USART6_CLK_DISABLE();
            break;
    }

    // Configure GPIOs
    pin_function(obj->pin_tx, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, 0));
    pin_function(obj->pin_rx, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, 0));

    serial_irq_ids[obj->index] = 0;
}

Ejemplo n.º 3

Archivo: serial_api.c Proyecto: Jinjeleta/gcc4mbed

void serial_free(serial_t *obj)
{
    // Reset UART and disable clock
    switch (SERIAL_OBJ(uart)) {
        case UART_1:
            __USART1_FORCE_RESET();
            __USART1_RELEASE_RESET();
            __USART1_CLK_DISABLE();
            break;
        case UART_2:
            __USART2_FORCE_RESET();
            __USART2_RELEASE_RESET();
            __USART2_CLK_DISABLE();
            break;
#if defined(USART3_BASE)
        case UART_3:
            __USART3_FORCE_RESET();
            __USART3_RELEASE_RESET();
            __USART3_CLK_DISABLE();
            break;
#endif
#if defined(UART4_BASE)
        case UART_4:
            __UART4_FORCE_RESET();
            __UART4_RELEASE_RESET();
            __UART4_CLK_DISABLE();
#if DEVICE_SERIAL_ASYNCH_DMA
            __HAL_RCC_DMA1_CLK_DISABLE();
#endif
            break;
#endif
#if defined(UART5_BASE)
        case UART_5:
            __UART5_FORCE_RESET();
            __UART5_RELEASE_RESET();
            __UART5_CLK_DISABLE();
            break;
#endif
#if defined(USART6_BASE)
        case UART_6:
            __USART6_FORCE_RESET();
            __USART6_RELEASE_RESET();
            __USART6_CLK_DISABLE();
            break;
#endif
#if defined(UART7_BASE)
        case UART_7:
            __UART7_FORCE_RESET();
            __UART7_RELEASE_RESET();
            __UART7_CLK_DISABLE();
            break;
#endif
#if defined(UART8_BASE)
        case UART_8:
            __UART8_FORCE_RESET();
            __UART8_RELEASE_RESET();
            __UART8_CLK_DISABLE();
            break;
#endif
    }
    // Configure GPIOs
    pin_function(SERIAL_OBJ(pin_tx), STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, 0));
    pin_function(SERIAL_OBJ(pin_rx), STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, 0));

    serial_irq_ids[SERIAL_OBJ(index)] = 0;
}

Ejemplo n.º 4

Archivo: serial_api.c Proyecto: AlessandroA/mbed

void serial_free(serial_t *obj)
{
    struct serial_s *obj_s = SERIAL_S(obj);
    
    // Reset UART and disable clock
    switch (obj_s->index) {
        case 0:
            __USART1_FORCE_RESET();
            __USART1_RELEASE_RESET();
            __USART1_CLK_DISABLE();
            break;
        case 1:
            __USART2_FORCE_RESET();
            __USART2_RELEASE_RESET();
            __USART2_CLK_DISABLE();
            break;
#if defined(USART3_BASE)
        case 2:
            __USART3_FORCE_RESET();
            __USART3_RELEASE_RESET();
            __USART3_CLK_DISABLE();
            break;
#endif
#if defined(UART4_BASE)
        case 3:
            __UART4_FORCE_RESET();
            __UART4_RELEASE_RESET();
            __UART4_CLK_DISABLE();
            break;
#endif
#if defined(UART5_BASE)
        case 4:
            __UART5_FORCE_RESET();
            __UART5_RELEASE_RESET();
            __UART5_CLK_DISABLE();
            break;
#endif
#if defined(USART6_BASE)
        case 5:
            __USART6_FORCE_RESET();
            __USART6_RELEASE_RESET();
            __USART6_CLK_DISABLE();
            break;
#endif
#if defined(UART7_BASE)
        case 6:
            __UART7_FORCE_RESET();
            __UART7_RELEASE_RESET();
            __UART7_CLK_DISABLE();
            break;
#endif
#if defined(UART8_BASE)
        case 7:
            __UART8_FORCE_RESET();
            __UART8_RELEASE_RESET();
            __UART8_CLK_DISABLE();
            break;
#endif
    }
    
    // Configure GPIOs
    pin_function(obj_s->pin_tx, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, 0));
    pin_function(obj_s->pin_rx, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, 0));

    serial_irq_ids[obj_s->index] = 0;
}

Ejemplo n.º 5

Archivo: serial_api.c Proyecto: Farewellly/mbed

void serial_free(serial_t *obj)
{
    // Reset UART and disable clock
    switch (SERIAL_OBJ(index)) {
        case 0:
            __USART1_FORCE_RESET();
            __USART1_RELEASE_RESET();
            __USART1_CLK_DISABLE();
            break;
        case 1:
            __USART2_FORCE_RESET();
            __USART2_RELEASE_RESET();
            __USART2_CLK_DISABLE();
#if DEVICE_SERIAL_ASYNCH_DMA
            __HAL_RCC_DMA1_CLK_DISABLE();
#endif
            break;
#if defined(USART3_BASE)
        case 2:
            __USART3_FORCE_RESET();
            __USART3_RELEASE_RESET();
            __USART3_CLK_DISABLE();
            break;
#endif
#if defined(UART4_BASE)
        case 3:
            __UART4_FORCE_RESET();
            __UART4_RELEASE_RESET();
            __UART4_CLK_DISABLE();
#if DEVICE_SERIAL_ASYNCH_DMA
            __HAL_RCC_DMA1_CLK_DISABLE();
#endif
            break;
#endif
#if defined(UART5_BASE)
        case 4:
            __UART5_FORCE_RESET();
            __UART5_RELEASE_RESET();
            __UART5_CLK_DISABLE();
            break;
#endif
#if defined(USART6_BASE)
        case 5:
            __USART6_FORCE_RESET();
            __USART6_RELEASE_RESET();
            __USART6_CLK_DISABLE();
            break;
#endif
#if defined(UART7_BASE)
        case 6:
            __UART7_FORCE_RESET();
            __UART7_RELEASE_RESET();
            __UART7_CLK_DISABLE();
            break;
#endif
#if defined(UART8_BASE)
        case 7:
            __UART8_FORCE_RESET();
            __UART8_RELEASE_RESET();
            __UART8_CLK_DISABLE();
            break;
#endif
    }
    
    // Configure GPIOs
    pin_function(SERIAL_OBJ(pin_tx), STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, 0));
    pin_function(SERIAL_OBJ(pin_rx), STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, 0));

    serial_irq_ids[SERIAL_OBJ(index)] = 0;

    DEBUG_PRINTF("UART%u: Free\n", obj->serial.module+1);
}

Ejemplo n.º 6

Archivo: serial_api.c Proyecto: AlessandroA/mbed-hal-st-stm32f4

void serial_free(serial_t *obj)
{
    // Reset UART and disable clock
    switch (obj->serial.module) {
        case 0:
            __USART1_FORCE_RESET();
            __USART1_RELEASE_RESET();
            __USART1_CLK_DISABLE();
            break;
        case 1:
            __USART2_FORCE_RESET();
            __USART2_RELEASE_RESET();
            __USART2_CLK_DISABLE();
            break;
#if defined(USART3_BASE)
        case 2:
            __USART3_FORCE_RESET();
            __USART3_RELEASE_RESET();
            __USART3_CLK_DISABLE();
            break;
#endif
#if defined(UART4_BASE)
        case 3:
            __UART4_FORCE_RESET();
            __UART4_RELEASE_RESET();
            __UART4_CLK_DISABLE();
            break;
#endif
#if defined(UART5_BASE)
        case 4:
            __UART5_FORCE_RESET();
            __UART5_RELEASE_RESET();
            __UART5_CLK_DISABLE();
            break;
#endif
        case 5:
            __USART6_FORCE_RESET();
            __USART6_RELEASE_RESET();
            __USART6_CLK_DISABLE();
            break;
#if defined(UART7_BASE)
        case 6:
            __UART7_FORCE_RESET();
            __UART7_RELEASE_RESET();
            __UART7_CLK_DISABLE();
            break;
#endif
#if defined(UART8_BASE)
        case 7:
            __UART8_FORCE_RESET();
            __UART8_RELEASE_RESET();
            __UART8_CLK_DISABLE();
            break;
#endif
    }
    // Configure GPIOs
    pin_function(obj->serial.pin_tx, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, 0));
    pin_function(obj->serial.pin_rx, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, 0));

    DEBUG_PRINTF("UART%u: Free\n", obj->serial.module+1);
}