static void adc_setup(void)
{
int i;
rcc_peripheral_enable_clock(&RCC_APB2ENR, RCC_APB2ENR_ADC1EN);
/* Make sure the ADC doesn't run during config. */
adc_off(ADC1);
/* We configure everything for one single timer triggered injected conversion. */
adc_disable_scan_mode(ADC1);
adc_set_single_conversion_mode(ADC1);
/* We can only use discontinuous mode on either the regular OR injected channels, not both */
adc_disable_discontinuous_mode_regular(ADC1);
adc_enable_discontinuous_mode_injected(ADC1);
/* We want to start the injected conversion with the TIM2 TRGO */
adc_enable_external_trigger_injected(ADC1,ADC_CR2_JEXTSEL_TIM2_TRGO);
adc_set_right_aligned(ADC1);
/* We want to read the temperature sensor, so we have to enable it. */
adc_enable_temperature_sensor(ADC1);
adc_set_sample_time_on_all_channels(ADC1, ADC_SMPR_SMP_28DOT5CYC);
adc_power_on(ADC1);
/* Wait for ADC starting up. */
for (i = 0; i < 800000; i++) /* Wait a bit. */
__asm__("nop");
adc_reset_calibration(ADC1);
while ((ADC_CR2(ADC1) & ADC_CR2_RSTCAL) != 0);
adc_calibration(ADC1);
while ((ADC_CR2(ADC1) & ADC_CR2_CAL) != 0);
}
void adc_setup(void) {
//ADC
rcc_peripheral_enable_clock(&RCC_AHBENR, RCC_AHBENR_ADC12EN);
rcc_peripheral_enable_clock(&RCC_AHBENR, RCC_AHBENR_IOPAEN);
//ADC
gpio_mode_setup(GPIOA, GPIO_MODE_ANALOG, GPIO_PUPD_NONE, GPIO0);
gpio_mode_setup(GPIOA, GPIO_MODE_ANALOG, GPIO_PUPD_NONE, GPIO1);
adc_off(ADC1);
adc_set_clk_prescale(ADC_CCR_CKMODE_DIV2);
adc_set_single_conversion_mode(ADC1);
adc_disable_external_trigger_regular(ADC1);
adc_set_right_aligned(ADC1);
/* We want to read the temperature sensor, so we have to enable it. */
adc_enable_temperature_sensor();
adc_set_sample_time_on_all_channels(ADC1, ADC_SMPR1_SMP_61DOT5CYC);
uint8_t channel_array[16];
channel_array[0]=16; // Vts (Internal temperature sensor
channel_array[0]=1; //ADC1_IN1 (PA0)
adc_set_regular_sequence(ADC1, 1, channel_array);
adc_set_resolution(ADC1, ADC_CFGR_RES_12_BIT);
adc_power_on(ADC1);
/* Wait for ADC starting up. */
int i;
for (i = 0; i < 800000; i++) /* Wait a bit. */
__asm__("nop");
}
static void adc_setup(void)
{
rcc_periph_clock_enable(RCC_ADC);
rcc_periph_clock_enable(RCC_GPIOA);
gpio_mode_setup(GPIOA, GPIO_MODE_ANALOG, GPIO_PUPD_NONE, GPIO0);
gpio_mode_setup(GPIOA, GPIO_MODE_ANALOG, GPIO_PUPD_NONE, GPIO1);
adc_power_off(ADC1);
adc_set_clk_source(ADC1, ADC_CLKSOURCE_ADC);
adc_calibrate_start(ADC1);
adc_calibrate_wait_finish(ADC1);
adc_set_operation_mode(ADC1, ADC_MODE_SCAN);
adc_disable_external_trigger_regular(ADC1);
adc_set_right_aligned(ADC1);
adc_enable_temperature_sensor();
adc_set_sample_time_on_all_channels(ADC1, ADC_SMPTIME_071DOT5);
adc_set_regular_sequence(ADC1, 1, channel_array);
adc_set_resolution(ADC1, ADC_RESOLUTION_12BIT);
adc_disable_analog_watchdog(ADC1);
adc_power_on(ADC1);
/* Wait for ADC starting up. */
int i;
for (i = 0; i < 800000; i++) { /* Wait a bit. */
__asm__("nop");
}
}
static void adc_setup(void)
{
int i;
rcc_peripheral_enable_clock(&RCC_APB2ENR, RCC_APB2ENR_ADC1EN);
/* Make sure the ADC doesn't run during config. */
adc_off(ADC1);
/* We configure everything for one single conversion. */
adc_disable_scan_mode(ADC1);
adc_set_single_conversion_mode(ADC1);
adc_disable_external_trigger_regular(ADC1);
adc_set_right_aligned(ADC1);
/* We want to read the temperature sensor, so we have to enable it. */
adc_enable_temperature_sensor(ADC1);
adc_set_sample_time_on_all_channels(ADC1, ADC_SMPR_SMP_28DOT5CYC);
adc_power_on(ADC1);
/* Wait for ADC starting up. */
for (i = 0; i < 800000; i++) /* Wait a bit. */
__asm__("nop");
adc_reset_calibration(ADC1);
adc_calibration(ADC1);
}
static void adc_setup(void)
{
int i;
rcc_peripheral_enable_clock(&RCC_APB2ENR, RCC_APB2ENR_ADC1EN);
/* Make sure the ADC doesn't run during config. */
adc_off(ADC1);
/* We configure everything for one single timer triggered injected conversion with interrupt generation. */
/* While not needed for a single channel, try out scan mode which does all channels in one sweep and
* generates the interrupt/EOC/JEOC flags set at the end of all channels, not each one.
*/
adc_enable_scan_mode(ADC1);
adc_set_single_conversion_mode(ADC1);
/* We want to start the injected conversion with the TIM2 TRGO */
adc_enable_external_trigger_injected(ADC1,ADC_CR2_JEXTSEL_TIM2_TRGO);
/* Generate the ADC1_2_IRQ */
adc_enable_eoc_interrupt_injected(ADC1);
adc_set_right_aligned(ADC1);
/* We want to read the temperature sensor, so we have to enable it. */
adc_enable_temperature_sensor(ADC1);
adc_set_sample_time_on_all_channels(ADC1, ADC_SMPR_SMP_28DOT5CYC);
adc_power_on(ADC1);
/* Wait for ADC starting up. */
for (i = 0; i < 800000; i++) /* Wait a bit. */
__asm__("nop");
adc_reset_calibration(ADC1);
while ((ADC_CR2(ADC1) & ADC_CR2_RSTCAL) != 0);
adc_calibration(ADC1);
while ((ADC_CR2(ADC1) & ADC_CR2_CAL) != 0);
}
static void adc_setup(void)
{
gpio_mode_setup(GPIOA, GPIO_MODE_ANALOG, GPIO_PUPD_NONE, GPIO0);
gpio_mode_setup(GPIOA, GPIO_MODE_ANALOG, GPIO_PUPD_NONE, GPIO1);
adc_off(ADC1);
adc_enable_temperature_sensor();
adc_disable_scan_mode(ADC1);
adc_set_sample_time_on_all_channels(ADC1, ADC_SMPR_SMP_480CYC);
adc_power_on(ADC1);
}
static void adc_setup(void)
{
int i;
rcc_periph_clock_enable(RCC_ADC1);
/* Make sure the ADC doesn't run during config. */
adc_power_off(ADC1);
/* We configure everything for one single timer triggered injected conversion with interrupt generation. */
/* While not needed for a single channel, try out scan mode which does all channels in one sweep and
* generates the interrupt/EOC/JEOC flags set at the end of all channels, not each one.
*/
adc_enable_scan_mode(ADC1);
adc_set_single_conversion_mode(ADC1);
/* We want to start the injected conversion with the TIM2 TRGO */
adc_enable_external_trigger_injected(ADC1,ADC_CR2_JEXTSEL_TIM2_TRGO);
/* Generate the ADC1_2_IRQ */
adc_enable_eoc_interrupt_injected(ADC1);
adc_set_right_aligned(ADC1);
/* We want to read the temperature sensor, so we have to enable it. */
adc_enable_temperature_sensor();
adc_set_sample_time_on_all_channels(ADC1, ADC_SMPR_SMP_28DOT5CYC);
/* Select the channels we want to convert.
* 16=temperature_sensor, 17=Vrefint, 13=ADC1, 10=ADC2
*/
channel_array[0] = 16;
channel_array[1] = 17;
channel_array[2] = 13;
channel_array[3] = 10;
adc_set_injected_sequence(ADC1, 4, channel_array);
adc_power_on(ADC1);
/* Wait for ADC starting up. */
for (i = 0; i < 800000; i++) /* Wait a bit. */
__asm__("nop");
adc_reset_calibration(ADC1);
adc_calibrate(ADC1);
}
void brick_init(void) {
// Wait 5ms so everything can power up
SLEEP_MS(5);
logging_init();
logsi("Booting %d\n\r", BRICK_DEVICE_IDENTIFIER);
logsi("Compiled on %s %s\n\r", __DATE__, __TIME__);
logsi("Processor family %s\n\r", IS_SAM3() ? "SAM3S" : "SAM4S");
led_init();
led_on(LED_STD_BLUE);
#ifdef LED_STD_RED
#if LOGGING_LEVEL == LOGGING_NONE
led_off(LED_STD_RED);
#else
led_on(LED_STD_RED);
#endif
#endif
logsi("LEDs initialized\n\r");
com_info.uid = uid_get_uid32();
// Add 0 at end for printing
char sn[MAX_BASE58_STR_SIZE] = {'\0'};
uid_to_serial_number(com_info.uid, sn);
set_serial_number_descriptor(sn, MAX_BASE58_STR_SIZE);
logsi("Unique ID %s (%lu)\n\r\n\r", sn, com_info.uid);
wdt_start();
logsi("Watchdog disabled\n\r");
mutex_init();
logsi("Mutexes initialized\n\r");
// Disable JTAG (Pins are needed for i2c)
#ifdef DISABLE_JTAG_ON_STARTUP
MATRIX->CCFG_SYSIO |= (CCFG_SYSIO_SYSIO12 |
CCFG_SYSIO_SYSIO4 |
CCFG_SYSIO_SYSIO5 |
CCFG_SYSIO_SYSIO6 |
CCFG_SYSIO_SYSIO7);
logsi("JTAG disabled\n\r");
#endif
com_info.current = COM_NONE;
PIO_InitializeInterrupts(15);
bricklet_clear_eeproms();
i2c_eeprom_master_init(TWI_BRICKLET);
logsi("I2C for Bricklets initialized\n\r");
usb_detect_configure();
adc_init();
adc_enable_temperature_sensor();
#ifndef NO_PERIODIC_ADC_CONVERISION
adc_start_periodic_conversion();
#endif
logsi("A/D converter initialized\n\r");
bricklet_init();
}
